Signal Processors
Description | Downloads | Specs | Ordering | ||
---|---|---|---|---|---|
2 Channel Microphone Mixer Pre-AmplifierA3044 |
|
| Dual microphone preamplifiers that can be mixed in stereo or operated separately. Dual inputs, Dual outputs. Includes 12V power supply. | ||
Phono Pre-AmplifierA3051 |
| A low noise pre-amplifier with RIAA equalisation circuitry for connecting your turntable up to a standard auxillary input on a mixer or amplifier. Suitable for use with 'Moving Magnet' pickups. powered by a 9V battery. Compact design fits easily behind an | |||
Phono Preamp with AUX inputA3052 |
|
| This phono preamp can be used to raise your turntable's output to make it compatible with modern amplifiers. At the same time, it adds standardised equalisation. Users may need this phono preamp because their turntable either doesn't have one, in which case they won't be able to play records without one. | ||
Audio Over IP Dante POE ReceiverA3164 |
|
| This device is designed to receive two channels audio signal from the Dante network, and converts to analogue RCA outputs. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to receive the low latency of signal from other devices which already connected on the same Dante network. | ||
Audio Over IP Dante POE TransmitterA3165 |
|
| This device is designed to provide two channels audio signal to the Dante network by the Euro terminal input. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to route the low latency of signal to other devices which already connected on the same Dante network. | ||
Digital Audio Cat5 Extender BoxA3194 |
|
| Allows digital signals to be transmitted using a single Cat5e or Cat6 cable. | ||
5.1CH Digital Audio ConverterA3195A |
|
| This Audio decoder can auto convert optical/coaxial channel (Support LPCM/PCM/RAW) input to 2.0 channel analog audio output, and supports decoding Dolby AC-3/DTS (included 5.1 RAW digital audio streaming). | ||
Headphone AmplifierA3196 |
|
| This single channel headphone amplifier is ideal for systems requiring additional audio level due to impedance differences between the audio source and headphone. | ||
4x8 Stereo Audio Switcher SystemA4460 |
|
| Designed to distribute 4 stereo audio input sources to 8 stereo output zones, this system is ideal for use in function centres, hotels, meeting rooms and domestic homes etc. It sends audio sources from one room to another with total ease. | ||
Dante Mic/Line 4 Input, 2 Output Dual Wall...A4816 |
|
| Dante Interface 4 x Mic/Line Inputs, 2 x Line Outputs | ||
Dante Mic/Line 4 Input, 4 Output Dual Wall...A4818 |
|
| Dante Interface 4 x Mic/Line Inputs, 4 x Outputs | ||
3 Pin XLR Line/Balanced Input UTP Balun Wa...A4820 |
|
| This 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | ||
Stereo RCA and 3.5mm Jack Input UTP Balun ...A4821 |
|
| This Stereo RCA and 3.5mm Jack Wallaplate can be used in a stand-alone point to point basis, allowing signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | ||
Stereo RCA Input UTP Balun WallplateA4822 |
|
| This Stereo RCA input wallplate can be used in a stand-alone point to point basis, allowing signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | ||
3 Pin XLR & Stereo RCA Input UTP Balun Wal...A4824 |
|
| This 3 pin XLR Line/Balanced and Stereo RCA input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | ||
Dual 3 Pin XLR Input UTP Balun WallplateA4825 |
|
| This Dual 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | ||
3 Pin XLR Balanced & Stereo RCA Output UTP...A4826 |
|
| This 3 pin XLR Balanced and Stereo RCA output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | ||
3 Pin XLR Line/Balanced Output UTP Balun W...A4827 |
|
| This 3 pin XLR Balanced Output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | ||
Stereo RCA Jack Output UTP Balun WallplateA4828 |
|
| This Stereo RCA Jack output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | ||
Dante Input/Output Converter Interface BoxA4830 |
| Interfaces 1 input and 1 output CSP UTP wallplates with Dante® systems. | |||
Dante 2 Input 4 Output Converter Interface...A4831 |
| Interfaces 2 input and 4 output CSP UTP wallplates with Dante® systems | |||
Local Input/Output Hub Interface BoxA4832 |
|
| A compact system hub for interfacing input and output wallplates together with existing zone audio amplifiers and audio sources. | ||
Active Three Pair Audio Signal Distributio...A4834 |
|
| This audio distribution system uses affordable UTP cabling to send up to three balanced inputs (terminal block) or mono RCA signals over long distances. | ||
Active Three Pair Audio Signal Distributio...A4835 |
|
| This audio distribution system uses affordable UTP cabling to send up to three balanced inputs (terminal block) or mono RCA signals over long distances. | ||
100V Line to Low Level AdapterA4903A |
|
| This small adaptor receives a 100V signal from one amplifier and reduces the level down to either balanced mic level or auxiliary level to feed into the input of a second amplifier. |