Projects

The Altronic projects range includes a huge array of Raspberry Pi, Arduino, robotic and specialist kit designs for enthusiast builders and STEM learning.

Toys

View as Grid List

Sort by

Display per page

These simple kits are a great introduction to the world of electronics. Basic principles are covered and assembly is completely solderless using a series of spring loaded terminals.

K2204

30 In 1 Electronics Lab Kit

These simple kits are a great introduction to the world of electronics. Basic principles are covered and assembly is completely solderless using a series of spring loaded terminals.

i h

K2222

This Electronic Science Lab will teach you about electronics from A to Z. You will learn about electronic parts, how to read schematics, and wiring diagrams. All this, while building up to 300 different projects.

i h

Single-sided, copper clad. 300 x 300mm +/- 5mm. Ideal for prototyping and one off PCB's.

H0755

300 x 300mm Single Sided Blank Fibreglass PCB

Single-sided, copper clad board. 300 x 300mm +/- 5mm. Ideal for prototyping and one off PCB's.

i h

A fully Integrated, Hall Effect-Based Linear AC/DC Current Sensor with a 30A rating. Typical applications include motor control, load detection and management, switch-mode power supplies, and over current protection Arduino projects.

Z6429

30A Current Sensor Module for Arduino

A fully Integrated, Hall Effect-Based Linear AC/DC Current Sensor with a 30A rating. Typical applications include motor control, load detection and management, switch-mode power supplies, and over current protection Arduino projects.

i h

Transform the pins of the micro bit motherboard into female headers allowing you to easily connect leads and build circuits. With the addition of a power module the breakout board can directly provide power for the micro bit board and load the capability of the breakout board.

Z6468

310 Tie Breadboard Shield for BBC Microbit

Transform the pins of the micro bit motherboard into female headers allowing you to easily connect leads and build circuits. With the addition of a power module the breakout board can directly provide power for the micro bit board and load the capability of the breakout board.

i h

Multi-colour reusable leads for prototyping and working
with breadboards. Assorted lengths in a handy
plastic case with separate compartments. P 1014A is
the perfect size for students. Includes 350 piece

P1018A

350pc Prototyping Wire Kit For Solderless Breadboards

Multi-colour reusable leads for prototyping and working with breadboards. Assorted lengths in a handy plastic case with separate compartments. P 1014A is the perfect size for students. Includes 350 piece

i h

A huge array of sensors for building into your Arduino project design. All feature standard pin headers for easy connection. The kit includes boards such as 1 channel relay, joystick, temp/humidity sensor, rotary encoder, microphones, hall effect sensor and much more!

Z6311

37 In 1 Arduino Compatible Sensor Module Kit

A huge array of sensors for building into your Arduino project design. All feature standard pin headers for easy connection. The kit includes boards such as 1 channel relay, joystick, temp/humidity sensor, rotary encoder, microphones, hall effect sensor and much more!

i h

Standard replacement 0.4mm nozzle for Creality Ender 3 3D Printer, suitable for use on other brands/types of 3D FDM printers also.

K-8600B

3D Printer Nozzle 0.4mm

Standard replacement 0.4mm nozzle for Creality Ender 3 3D Printer, suitable for use on other brands/types of 3D FDM printers also.

i h

Replacement pneumatic connectors to suit Creality Ender 3. Includes extruder and hot end threaded fittings and tube clips.

K-8600C

3D Printer Pneumatic Bowden Tube Connectors

Replacement pneumatic connectors to suit Creality Ender 3. Includes extruder and hot end threaded fittings and tube clips.

i h

Replacement teflon bowden tubing to suit Creality Ender and other brands/types of 3D printer. 1m length.

K-8600D

3D Printer Teflon Bowden Tubing 1m

Replacement teflon bowden tubing to suit Creality Ender and other brands/types of 3D printer. 1m length.

i h

A 13,500RPM flat top & bottom hobby motor commonly found in slot cars, robotics kits, toys and much more! 8.64gcm torque @ max efficiency.

J0024

3V Low Torque F130 Hobby Motor

A 13,500RPM flat top & bottom hobby motor commonly found in slot cars, robotics kits, toys and much more! 8.64gcm torque @ max efficiency.

i h

Ideal for adding nigh vision to a pi camera or other surveillance or monitoring application. Provides 3W of infra red light. Requires 5V DC input. Sold in a pair.

Z6471

3W Infra Red LED Module Pair For Cameras

Ideal for adding nigh vision to a pi camera or other surveillance or monitoring application. Provides 3W of infra red light. Requires 5V DC input. Sold in a pair.

i h

This is a 5V 4-Channel Relay interface board, Be able to control various appliances, and other equipments equipment with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
5V 4-Channel Relay interface board, and each one needs 15-20mA Driver Current
Equiped

Z6327

4 Channel 5V Relay Control Board Module/Shield

This is a 5V 4-Channel Relay interface board, Be able to control various appliances, and other equipments equipment with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). 5V 4-Channel Relay interface board, and each one needs 15-20mA Driver Current

i h

This control board features 4 x 3A 120V AC/24V DC rated relays for building in device control, and trigger other systems in your design.

Z6462

4 Relay Control Board for BBC Microbit

This control board features 4 x 3A 120V AC/24V DC rated relays for building in device control, and trigger other systems in your design.

i h

10,000RM rated hobby motor commonly found in robotics kits, toys and much more! 3-12VDC operation. 4.5V constant nominal operating voltage. 22.42gcm torque @ max efficiency.

J0026

4.5V Low Torque F260 Hobby Motor

10,000RM rated hobby motor commonly found in robotics kits, toys and much more! 3-12VDC operation. 4.5V constant nominal operating voltage. 22.42gcm torque @ max efficiency.

i h

Standard 0.1 inch spacings. Accepts all ICs, transistors, diodes, leds and passives. Uses solid hook up wire for interconnections. Boards are keyed to enable easy expansion.

P1002

400 Tie Point Interlocking Solderless Breadboard

Standard 0.1 inch spacings. Accepts all ICs, transistors, diodes, leds and passives. Uses solid hook up wire for interconnections. Boards are keyed to enable easy expansion.

i h

These German designed pre-built amplifier modules are a quick cost effective
solution for custom audio projects. All you need to do is connect a
power supply, speaker and an input. Each module is encapsulated in epoxy
resin, offering excellent durabili

A0705

40W Mono Amplifier Module

These German designed pre-built amplifier modules are a quick cost effective solution for custom audio projects. All you need to do is connect a power supply, speaker and an input. Each module is encapsulated in epoxy resin, offering excellent durability and reliability.

i h

Utilises the 44E hall effect sensor for contactless magnetic switching. Output drops to ground when triggered. 3.3-5V input. 2 mounting screws. Size: 15x18x7mm

Z6367A

44E Hall Effect Magnetic Sensor Breakout Module

Utilises the 44E hall effect sensor for contactless magnetic switching. Output drops to ground when triggered. 2 mounting screws. Size: 15x18x7mm

i h

Allows easier access to SD card slots in custom cases and enclosures for Pi, 3D printers & IoT boards.

Z6483

46cm Micro SD Card Extender Cable

Allows easier access to SD card slots in custom cases and enclosures for Pi, 3D printers & IoT boards.

i h

A geared motor with lightweight plastic housing. 5mm double flat shaft. 0.8kg/cm torque. Suits J 0101 rubber wheel. Max 130rpm no load. 1.5A stall.

J0016

48:1 Geared Motor With Plastic Housing

A geared motor with lightweight plastic housing. 5mm double flat shaft. 0.8kg/cm torque. Suits J 0101 rubber wheel. Max 130rpm no load. 1.5A stall.

i h

Available in either 2WD or 4WD configuration this robotic vehicle chassis features individual motors for each wheel, fitted with encoding wheels for integration with control sensors. It&rsquos the ideal base for your own Arduino powered robo-car design.

K1092

4WD Robot Builders Motorised Base

Available in either 2WD or 4WD configuration this robotic vehicle chassis features individual motors for each wheel, fitted with encoding wheels for integration with control sensors. It&rsquos the ideal base for your own Arduino powered robo-car design.

i h

A fun LED cube featuring 64 blue LEDs for creating cool lighting effects. This kit has been designed to be easier to construct by using pre-made LED module strips and is housed with the Arduino control board and USB FTDI interface inside a laser cut acrylic case.

K8109

4x4x4 Arduino Based Blue LED Acrylic Cube Kit

A fun LED cube featuring 64 blue LEDs for creating cool lighting effects. This kit has been designed to be easier to construct by using pre-made LED module strips and is housed with the Arduino control board and USB FTDI interface inside a laser cut acrylic case.

i h

This tiny and lightweight servo can rotate 360 degrees, and works just like the standard servo. You can use any servo code, hardware or library to control these servos.

Z6393

55g 360º Continuous Metal Servo Motor

This tiny and lightweight MG995 style servo motor can rotate 360 degrees, and works just like the standard servo. You can use any servo code, hardware or library to control these servos.

i h

A fully Integrated, Hall Effect-Based Linear AC/DC Current Sensor with a 5A rating. Typical applications include motor control, load detection and management, switch-mode power supplies, and over current protection Arduino projects.

Z6428

5A Current Sensor Module for Arduino

A fully Integrated, Hall Effect-Based Linear AC/DC Current Sensor with a 5A rating. Typical applications include motor control, load detection and management, switch-mode power supplies, and over current protection Arduino projects.

i h

This 5mm tubing is made of silicone rubber which is flexible, resistant to high temperatures and does not deteriorate outdoors.

J0083

5mm Silicon Tubing 1m Length - Suits J0080 Pump

This 5mm tubing is made of silicone rubber which is flexible, resistant to high temperatures and does not deteriorate outdoors.

NEW

i h

Shop Products

Projects

Follow us