| Description | Downloads | Specs | Ordering | ||
|---|---|---|---|---|---|
 |
8mm Windsock To Suit C8911AC0338 |
| This windsock is designed specifically to suit C8911A headband microphone and is sold as both a spare part and as a generic unit. | ||
 |
12mm Lapel Microphone WindsockC0337 |
| Used to negate breath noise and eliminate wind or breath "pop". This windsock is designed specifically to suit our lapel microphone and is sold as both a spare part and as a generic unit. | ||
 |
CB Type Microphone Mounting ClipC0336 |
| Microphone clip to suit the C 0333/C 0334 / C 0335 range of CB microphones. | ||
 |
CB Type Balanced Microphone With Bare EndsC0335 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord 2m (including switch pair). Suitable for CB''''s, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz | ||
 |
5 Pin XLR CB Type Balanced MicrophoneC0334 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord (including switch pair). Suitable for CB's, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz (C 0334), 300Hz - 6kHz (C 0335) | ||
 |
CB Type Microphone With Bare EndsC0333 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord (including switch pair). Suitable for CB's, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz (C 0334), 300Hz - 6kHz (C 0335) | ||
 |
4 Input Microphone MixerA2620 |
|
| This compact mono mixer allows 4 channels of audio to be mixed via 6.35mm unbalanced connections. It features 4 x 6.35mm unbalanced inputs, 1 x 6.35mm balanced master output, master volume control. Can be operated by 9V battery or 12V plugpack. Sold se | |
 |
Attenuator Volume Control 100W 100V Line W...A2339 |
| This controller has been designed to install to a double electrical flush box or wall mounting block. Massive 100 watt capacity available. 11 settings plus off. Fitted with a 24V override relay. 2 Year Warranty | ||
 |
1U Raw Aluminium 19" Rack PanelH5111 |
|
| Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel. | |
|
3U Raw Aluminium 19" Rack PanelH5113 |
|
| Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel. | |
 |
2U Black Anodised Aluminium 19" Rack PanelH5132 |
|
| Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel. | |
 |
2U XLR 24 Way Patch Panel 19" Rack PanelH5172 |
|
| Pre-punched with either 12(1U) or 24(2U). Tough black powdercoated finish. H 5170 & H 5172 suit the following connectors: P 0804 XLR 3 Pin Female P 0824 XLR 5 Pin Female P 0904 Amphenol XLR 3 Pin Female P 0924 Amphenol XLR 5 Pin Female Note: Thi | |
 |
38U 600mm Deep 19" Rack FrameH5438A |
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. | ||
 |
450mm Deep 19" Rack Frame Louvered Top PanelH5602 |
|
| A vented steel panel designed to suit the range of Black rack frames. It is louvered to allow heat to flow up and away from the cabinet but reduce the amount of dust and dirt collected on top of the equipment within the rack. | |
 |
6U 450mm Deep 19" Rack Frame Panel SetH5606 |
|
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audi | |
|
15U 450mm Deep 19" Rack Frame Panel SetH5615 |
|
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audi | |
|
18U 450mm Deep 19" Rack Frame Panel SetH5618 |
|
| This 18U panel sets provide a neat finish, concealing all enclosed equipment and prevent unauthorised access to the rack. Each set includes a solid top panel and two side panels to suit the 450mm black rack frames. To add ventilation, we suggest using the H5602 vented top panel. | |
|
30U 450mm Deep 19" Rack Frame Panel SetH5630 |
|
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audi | |
 |
9U Perspex 19" Rack DoorH5709A |
|
| These lockable perspex doors may be mounted on the front or rear of the rack. Note, a pop-rivet gun is required for attaching door to the rack frame. Add 30mm to the depth measurement of your rack per door. All doors are keyed alike. | |
 |
24U Steel 19" Rack DoorH5764A |
|
| These lockable vented steel doors may be mounted on the front or rear of the rack. Note, a pop-rivet gun is required for attaching door to the rack frame. Add 30mm to the depth measurement of your rack per door. All doors are keyed alike. 24U. | |
 |
Balanced To Unbalanced Converter XLR-RCAA2513 |
| Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control. +10dB max signal gain. Steps up input signal by factor of 16, ie 20mV in = 320mV out. | ||
 |
Microphone Tie Clip Lavalier for C7195A/B/...C7197A |
| Lapel microphone to suit C7195A, C7195B and C7195C beltpack. | ||
 |
Half Rack 19" Rack BracketH4990 |
|
| H 4990 allows the mounting of two "half rack" units into a 19" 1RU space on a rack frame. Depth: 90mm. Note: Pictured with product. | |
 |
Black Nylon Washer Pk 100H5401 ROHS |
| Nylon washer black suit M6 Pack Qty: 100 | ||
 |
1U Cable Support 19" Rack PanelH4605 |
| This 19" cable support bar is great for organising and supporting all your interconnect cables to the patch panels. Cables can be anchored to the panel by using cable ties to secure the cables to the supports. Black powdercoated finish. | ||
 |
300mm Black Gooseneck Microphone ExtensionC0411 |
| Microphone gooseneck incorporating 5/8" thread male to female. Matching bench mount bases C 0420/21. 300mm Black. | ||
 |
Studio Quality Entertainers Handheld Unidi...C0392 |
|
| This fine quality microphone has been styled on the famous Shure&trade Bros SM58. In our opinion the reproduction is every bit as good as the genuine article. Housed in a sturdy diecast body and fitted with a silent action reed type on/off switch. | |
 |
Attenuator Volume Control 5 Zone Evac 40W ...A2347 |
|
| May be configured to either five single inputs to five outputs or one input to five outputs. Each zone has a 40W and 100W load capacity respectively, with a total panel capacity of 200W and 500W. Has 11 settings plus 'off'. The input and outputs are conn | |
|
9U Steel 19" Rack DoorH5750A |
|
| These lockable vented steel doors may be mounted on the front or rear of the rack. Note, a pop-rivet gun is required for attaching door to the rack frame. Add 30mm to the depth measurement of your rack per door. All doors are keyed alike. | |
|
24U 450mm Deep 19" Rack Frame Panel SetH5624 |
|
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audi | |
|
9U 450mm Deep 19" Rack Frame Panel SetH5609 |
|
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audi | |
|
18U 450mm Deep 19" Rack FrameH5518A |
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equi | ||
|
12U 450mm Deep 19" Rack FrameH5512A |
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. | ||
|
6U 450mm Deep 19" Rack FrameH5506 |
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. | ||
|
4U 450mm Deep 19" Rack FrameH5504 |
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. | ||
|
38U 600mm Deep 19" Rack Frame Panel SetH5478 |
|
| Panel sets provide a neat finish, concealing all enclosed equipment and prevent unauthorised access to the rack. Each set includes a solid top panel and two side panels. 38U. 600mm deep. To add ventilation, we suggest using the H5603 vented top panel. | |
|
30U 600mm Deep 19" Rack Frame Panel SetH5470 |
|
| Panel sets provide a neat finish, concealing all enclosed equipment and prevent unauthorised access to the rack. Each set includes a solid top panel and two side panels. 30U. 600mm deep. To add ventilation, we suggest using the H5603 vented top panel. | |
 |
Rack Frame Castor Wheel Pk 4H5295 |
| Includes 2 free wheeling and 2 with locking mechanisms. Suits all rack frames. | ||
 |
Guitar Pickup Lead To Suit UHF Beltpack Tr...C8909 |
| Mini 3pin XLR to Mono 6.35mm Jack Plug suitable for connecting a guitar pickup to a Redback wireless beltpack transmitter. | ||
 |
50W Portable PA Cover To Suit Okayo C 71XX...C7199 |
| Bag to suit 50 Okayo portable PA models, C7180-C7185B. | ||
 |
Gooseneck Shock Mount Microphone BaseC0484 |
| Flush mount friction fit gooseneck base. Suitable for C 0410-C 0413 goosenecks. Mounting hole size: 50.5mm. | ||
|
2U Raw Aluminium 19" Rack PanelH5112 |
|
| Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel. | |
|
30U Steel 19" Rack DoorH5770A |
|
| These lockable vented steel doors may be mounted on the front or rear of the rack. Note, a pop-rivet gun is required for attaching door to the rack frame. Add 30mm to the depth measurement of your rack per door. All doors are keyed alike. 30U. | |
 |
Unbalanced to Balanced Converter RCA-XLRA2514 |
| Unbalanced 10K Ohm 2 x RCA to balanced 600 Ohm 3 pin male XLR with level control. -10dB max signal gain. | ||
 |
Protective Pouch To Suit C7195A/B BeltpackC7200 |
| Protective poromeric pouch to suit C7195A or C7195B beltpack lavalier transmitter. |
Designed & manufactured in Australia.
