| Description | Downloads | Specs | Ordering | ||
|---|---|---|---|---|---|
 |
10mm Pencil Microphone WindsockC0345 |
| Used to negate breath noise and eliminate wind or breath “pop”. | ||
 |
40mm Ball Microphone WindsockC0344 |
| Used to negate breath noise and eliminate wind or breath “pop”. | ||
 |
27mm Medium Microphone WindsockC0342 |
| Used to negate breath noise and eliminate wind or breath “pop”. | ||
 |
20mm Pencil Microphone WindsockC0340 |
| Used to negate breath noise and eliminate wind or breath 'pop' | ||
 |
8mm Windsock To Suit C8911AC0338 |
| This windsock is designed specifically to suit C8911A headband microphone and is sold as both a spare part and as a generic unit. | ||
 |
12mm Lapel Microphone WindsockC0337 |
| Used to negate breath noise and eliminate wind or breath "pop". This windsock is designed specifically to suit our lapel microphone and is sold as both a spare part and as a generic unit. | ||
 |
CB Type Microphone Mounting ClipC0336 |
| Microphone clip to suit the C 0333/C 0334 / C 0335 range of CB microphones. | ||
 |
CB Type Balanced Microphone With Bare EndsC0335 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord 2m (including switch pair). Suitable for CB''''s, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz | ||
 |
5 Pin XLR CB Type Balanced MicrophoneC0334 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord (including switch pair). Suitable for CB's, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz (C 0334), 300Hz - 6kHz (C 0335) | ||
 |
CB Type Microphone With Bare EndsC0333 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord (including switch pair). Suitable for CB's, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz (C 0334), 300Hz - 6kHz (C 0335) | ||
 |
4 Input Microphone MixerA2620 |
|
| This compact mono mixer allows 4 channels of audio to be mixed via 6.35mm unbalanced connections. It features 4 x 6.35mm unbalanced inputs, 1 x 6.35mm balanced master output, master volume control. Can be operated by 9V battery or 12V plugpack. Sold se | |
 |
Attenuator Volume Control 100W 100V Line W...A2339 |
| This controller has been designed to install to a double electrical flush box or wall mounting block. Massive 100 watt capacity available. 11 settings plus off. Fitted with a 24V override relay. 2 Year Warranty | ||
 |
1U Raw Aluminium 19" Rack PanelH5111 |
|
| Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel. | |
|
3U Raw Aluminium 19" Rack PanelH5113 |
|
| Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel. | |
 |
2U Black Anodised Aluminium 19" Rack PanelH5132 |
|
| Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel. | |
 |
2U XLR 24 Way Patch Panel 19" Rack PanelH5172 |
|
| Pre-punched with either 12(1U) or 24(2U). Tough black powdercoated finish. H 5170 & H 5172 suit the following connectors: P 0804 XLR 3 Pin Female P 0824 XLR 5 Pin Female P 0904 Amphenol XLR 3 Pin Female P 0924 Amphenol XLR 5 Pin Female Note: Thi | |
 |
38U 600mm Deep 19" Rack FrameH5438A |
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. | ||
 |
450mm Deep 19" Rack Frame Louvered Top PanelH5602 |
|
| A vented steel panel designed to suit the range of Black rack frames. It is louvered to allow heat to flow up and away from the cabinet but reduce the amount of dust and dirt collected on top of the equipment within the rack. | |
 |
6U 450mm Deep 19" Rack Frame Panel SetH5606 |
|
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audi | |
|
15U 450mm Deep 19" Rack Frame Panel SetH5615 |
|
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audi | |
|
18U 450mm Deep 19" Rack Frame Panel SetH5618 |
|
| This 18U panel sets provide a neat finish, concealing all enclosed equipment and prevent unauthorised access to the rack. Each set includes a solid top panel and two side panels to suit the 450mm black rack frames. To add ventilation, we suggest using the H5602 vented top panel. | |
|
30U 450mm Deep 19" Rack Frame Panel SetH5630 |
|
| These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audi | |
 |
9U Perspex 19" Rack DoorH5709A |
|
| These lockable perspex doors may be mounted on the front or rear of the rack. Note, a pop-rivet gun is required for attaching door to the rack frame. Add 30mm to the depth measurement of your rack per door. All doors are keyed alike. | |
 |
24U Steel 19" Rack DoorH5764A |
|
| These lockable vented steel doors may be mounted on the front or rear of the rack. Note, a pop-rivet gun is required for attaching door to the rack frame. Add 30mm to the depth measurement of your rack per door. All doors are keyed alike. 24U. | |
 |
Balanced To Unbalanced Converter XLR-RCAA2513 |
| Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control. +10dB max signal gain. Steps up input signal by factor of 16, ie 20mV in = 320mV out. |
Designed & manufactured in Australia.
