| Description | Downloads | Specs | Ordering | ||
|---|---|---|---|---|---|
 |
Windsock to suit C0361C0347 |
| Used to negate breath noise and eliminate wind or breath “pop”. Suits C 0361 shotgun microphone. | ||
 |
Windsock to suit C0375C0346 |
| Used to negate breath noise and eliminate wind or breath "pop". Size refers to inside diameter of windsock opening.7mm | ||
 |
10mm Pencil Microphone WindsockC0345 |
| Used to negate breath noise and eliminate wind or breath “pop”. | ||
 |
40mm Ball Microphone WindsockC0344 |
| Used to negate breath noise and eliminate wind or breath “pop”. | ||
 |
27mm Medium Microphone WindsockC0342 |
| Used to negate breath noise and eliminate wind or breath “pop”. | ||
 |
20mm Pencil Microphone WindsockC0340 |
| Used to negate breath noise and eliminate wind or breath 'pop' | ||
 |
8mm Windsock To Suit C8911AC0338 |
| This windsock is designed specifically to suit C8911A headband microphone and is sold as both a spare part and as a generic unit. | ||
 |
12mm Lapel Microphone WindsockC0337 |
| Used to negate breath noise and eliminate wind or breath "pop". This windsock is designed specifically to suit our lapel microphone and is sold as both a spare part and as a generic unit. | ||
 |
CB Type Microphone Mounting ClipC0336 |
| Microphone clip to suit the C 0333/C 0334 / C 0335 range of CB microphones. | ||
 |
CB Type Balanced Microphone With Bare EndsC0335 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord 2m (including switch pair). Suitable for CB''''s, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz | ||
 |
5 Pin XLR CB Type Balanced MicrophoneC0334 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord (including switch pair). Suitable for CB's, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz (C 0334), 300Hz - 6kHz (C 0335) | ||
 |
CB Type Microphone With Bare EndsC0333 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord (including switch pair). Suitable for CB's, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz (C 0334), 300Hz - 6kHz (C 0335) | ||
 |
Attenuator Volume Control 100W 100V Line W...A2339 |
| This controller has been designed to install to a double electrical flush box or wall mounting block. Massive 100 watt capacity available. 11 settings plus off. Fitted with a 24V override relay. 2 Year Warranty | ||
 |
Balanced To Unbalanced Converter XLR-RCAA2513 |
| Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control. +10dB max signal gain. Steps up input signal by factor of 16, ie 20mV in = 320mV out. | ||
 |
300mm Black Gooseneck Microphone ExtensionC0411 |
| Microphone gooseneck incorporating 5/8" thread male to female. Matching bench mount bases C 0420/21. 300mm Black. | ||
 |
Studio Quality Entertainers Handheld Unidi...C0392 |
|
| This fine quality microphone has been styled on the famous Shure&trade Bros SM58. In our opinion the reproduction is every bit as good as the genuine article. Housed in a sturdy diecast body and fitted with a silent action reed type on/off switch. | |
 |
Attenuator Volume Control 5 Zone Evac 40W ...A2347 |
|
| May be configured to either five single inputs to five outputs or one input to five outputs. Each zone has a 40W and 100W load capacity respectively, with a total panel capacity of 200W and 500W. Has 11 settings plus 'off'. The input and outputs are conn | |
 |
Guitar Pickup Lead To Suit UHF Beltpack Tr...C8909 |
| Mini 3pin XLR to Mono 6.35mm Jack Plug suitable for connecting a guitar pickup to a Redback wireless beltpack transmitter. | ||
 |
Gooseneck Shock Mount Microphone BaseC0484 |
| Flush mount friction fit gooseneck base. Suitable for C 0410-C 0413 goosenecks. Mounting hole size: 50.5mm. | ||
 |
Unbalanced to Balanced Converter RCA-XLRA2514 |
| Unbalanced 10K Ohm 2 x RCA to balanced 600 Ohm 3 pin male XLR with level control. -10dB max signal gain. |
