|
Description |
Downloads |
Specs |
Ordering |
|
 |
A4220 NEW
|
|
- Modular design allows for mix and match amplifiers within 1RU rack space.
- Class-D design with excellent performance and efficiency.
- LED indicators for protection mode, clipping condition and signal presence.
- 100V line or 8 ohm output via screw terminals.
- Stereo RCA line input.
- Balanced line input via 3 pin Euroblock pluggable terminal.
- High pass filter at 180Hz -3dB.
- Built-in short circuit, overload and high temperature protection.
- 2 year warranty.
|
|
This 120W PA zone amplifier developed by Redback, allows installers to mix and match amplifiers within a 1RU 19” rack space. |
 |
H1238 NEW
|
|
|
|
Chrome Plated Brass. Tapped to suit metric M3 machine Screws
|
 |
A4565C NEW
|
|
- Tones conform to AS 1670.4
- Standard 1U 19” rack mount case
- Interfaces with Fire Indicator Boards
- Remote operation of Alert, Evac, Chime, Fire Test, Fire Alarm & Cancel tones
- MP3 based tone playback (with backup hard coded Alert, Evac and Bell tones)
- 24V DC operation
- Auto/Manual/Isolate keyswitch
- Key switch to 003 standard
- Local operation of Alert, Evac and PA
- MP3 based Voice Over messages for Alert and Evac cycles
- Microphone socket for PA use
- Provision for BGM (back ground music)
- Provision for Auxiliary input with front volume control
- Bell chime facility
- Switched 24V DC output for override relays on volume controls
- Switched 24V DC output for strobe operation for Alert mode
- Switched 24V DC output for strobe operation for Evac mode
- Switched 24VDC output for bell mode
- On-board timer for automatic Alert to Evac switchover, adjustable from 30secs to 7.5min in 30 second increments
- Externally operated inputs are activated by switching to ground
- Auxiliary level output
- Suitable for any amplifier with an auxiliary input
- 10 Year Warranty
- Australian Designed and Manufactured
|
|
This easy to operate building alert & evacuation controller controller is designed around industry standard building requirements. When connected to a paging system amplifier, occupants can be alerted and/or evacuated in the event of an emergency eg: fire, gas leak, bomb scare, earthquake. |
 |
A4437 NEW
|
|
- 4 mic or line inputs
- Balanced line or RCA outputs
- VOX priority on input 1 and 2
- Phantom power ON/OFF for mic inputs
- Remote evacuation system muting contacts
- 24V DC operation
- Individual volume, treble and bass for all inputs
- Provision for A4573 alert evac tone generator module
- Australian designed and manufactured.
|
|
Works as a stand alone audio processor with four mic/line inputs for microphone and music sources. When the FIB operates it triggers these contacts, rending the local PA/BGM system inoperative so the main emergency evacuation system has precedence. |
 |
M8066 NEW
|
|
- Isolated design for maximum electrical safety
- Pure sine wave output
- Certified to Australian Standard AS/NZS 4763.2011
- Multi-function LCD readout
- DC/AC isolated design
- Safety authority tested for reliable & safe operation
- Over temperature, over voltage, over load and short circuit protection
- Low voltage cut off
- Excellent voltage regulation
- Binding post connection to battery
- Temperature controlled cooling fan.
|
|
This compact inverter is designed to deliver pure AC output for powering difficult loads such as appliances with switchmode power supplies (computers, displays & game consoles) and voltage sensitive devices. |
 |
C1063 NEW
|
|
- Durable and compact of cabinet PA mounting speaker.
- Industrial powdercoated steel bracket with stainless steel hardware.
- Full range of sound through 2-way driver.
- Long throw speaker system with maximum SPL at 116 dB.
- Screw terminals for loop in, loop out connection in 100V line systems.
- Extra cable gland and knock out provided for loop in, loop out wiring.
- 8 Ohm selection on power tap switch.
- IP55 moisture and dust protection rating.
- Superb sound quality for both music and speech intelligibility.
- Various power switch tapping 150W / 75W / 38W.
- Convenient U-bracket installation.
|
|
This all weather long throw PA speaker features a two-way driver, including 8-inch woofer and 1-inch tweeter for PA sound projection. |
 |
C1064 NEW
|
|
- Durable and compact of cabinet PA mounting speaker.
- Industrial powdercoated steel bracket with stainless steel hardware.
- Full range of sound through 2-way driver.
- Long throw speaker system with maximum SPL at 116 dB.
- Screw terminals for loop in, loop out connection in 100V line systems.
- Extra cable gland and knock out provided for loop in, loop out wiring.
- 8 Ohm selection on power tap switch.
- IP55 moisture and dust protection rating.
- Superb sound quality for both music and speech intelligibility.
- Various power switch tapping 150W / 75W / 38W.
- Convenient U-bracket installation.
|
|
This all weather long throw PA speaker features a two-way driver, including 8-inch woofer and 1-inch tweeter for PA sound projection. |
 |
M8002 NEW
|
|
- Isolated design for maximum electrical safety
- Pure sine wave output
- Automatic AC transfer
- RCD Safety Switch
- Certified to Australian Standard AS/NZS 4763.2011
- DC/AC isolated design
- Safety authority tested for reliable & safe operation
- Over temperature, over voltage, over load and short circuit protection
- Low voltage cut off
- Excellent voltage regulation
- Binding post connection to battery
- Temperature controlled cooling fan.
|
COMING SOONThis item is arriving soon. |
This Powerhouse BlackMax inverter delivers a pure sine wave AC output, ideal for powering demanding loads. Fitted with integrated automatic AC transfer switch ensures seamless switching between mains and inverter power, providing uninterrupted operation for connected appliances. |
 |
D0889 NEW
|
|
- Offering the best protection in its class, protecting against damaging surges
- Modern, stylish LCD display indicates voltage in/out, amount of load and remaining capacity
- The AVR automatically bucks/boosts unstable fluctuating utility voltages, bringing them within 10% of nominal voltage range and thereby protecting valuable equipment
- Compact design at just 300mm deep
- Intelligent slot for SNMP communications card
- Battery is easily hot swappable and user replaceable
- Designed to run cool without fans
- After an extended power outage the UPS will turn back on and resume equipment functionality once power has returned
- Allows for orderly shutdown without software
- Free, downloadable NetGuard software provides complete power monitoring
- The plugged in UPS will continue to charge internal batteries whether the unit is on or off
- Comes standard with 5 Australian sockets and 2 IEC outlets.
- The UPS can turn on equipment when it is off, simply by connecting equipment and turning the UPS on
- Plug and play on any computer or NAS drive
|
|
The Defender Rackmount 1500VA UPS expands the successful Defender Range by building the popular features into a Rack Mount style. At 300mm deep, this is the perfect UPS for shallow, wall mounted Comms cabinets. |
 |
K8610 NEW
|
|
|
|
This high performance 3D printer with a more aesthetic, streamlined design, features a brand new nozzle made of brass that can stand up to +300°C printing temperature and is compatible with PLA, ABS, PVA, TPU, PA, PETG and wood. |
 |
A4222 NEW
|
|
- Modular design allows for mix and match amplifiers within 1RU rack space.
- Class-D design with excellent performance and efficiency.
- LED indicators for protection mode, clipping condition and signal presence.
- 100V line or 8 ohm output via screw terminals.
- Stereo RCA line input.
- Balanced line input via 3 pin Euroblock pluggable terminal.
- High pass filter at 180Hz -3dB.
- Built-in short circuit, overload and high temperature protection.
- 2 year warranty.
|
|
This 240W PA zone amplifier developed by Redback, allows installers to mix and match amplifiers within a 1RU 19” rack space. |
 |
A4423 NEW
|
|
- 1 microphone/ 4 line inputs (mono mixed internally)
- Front 3.5mm music input (overrides rear input 4 input)
- Bluetooth audio connection (overrides input 4 front and rear inputs)
- 2 outputs via XLR/RCA 1V balanced
- Level controls for all inputs
- Separate bass and treble controls on all inputs
- Adjustable input sensitivity on all RCA line inputs
- Phantom power selection on Mic inputs (12V DC)
- Route signals to each output or both outputs
- 24V DC input
- 24V DC battery back up terminals
- 1RU 19” rack mount case
- 10 Year Warranty
- Australian designed & assembled
|
|
The Redback® mixer delivers a flexible and installer-friendly solution with one microphone/line input and three additional line inputs (all internally mixed to mono), plus a front-panel 3.5mm music input and integrated Bluetooth® receiver.
|
 |
A4221 NEW
|
|
- Modular design allows for mix and match amplifiers within 1RU rack space.
- Class-D design with excellent performance and efficiency.
- LED indicators for protection mode, clipping condition and signal presence.
- 100V line or 8 ohm output via screw terminals.
- Stereo RCA line input.
- Balanced line input via 3 pin Euroblock pluggable terminal.
- High pass filter at 180Hz -3dB.
- Built-in short circuit, overload and high temperature protection.
- 2 year warranty.
|
|
This 2 x 120W PA zone amplifier developed by Redback, allows installers to mix and match amplifiers within a 1RU 19” rack space. |
 |
H1242 NEW
|
|
|
|
Chrome Plated Brass. Tapped to suit metric M3 machine Screws
Pack of 1000pcs. M3 x 20mm. |
 |
A4424 NEW
|
|
- Six mic / line input channels.
- Two outputs via XLR/RCA 1V balanced.
- Level, bass and treble control on all inputs.
- Adjustable input sensitivity.
- Phantom power selection on each input.
- Route signals to each output or both outputs.
- Includes power supply
- 1RU 19” rack mount case.
- Australian designed & assembled
|
|
New to the Redback mixer stable, this model incorporates six inputs which can be routed to 1 of 2 outputs or both as the installation requires. Inputs can be configured for either RCA line level signals or 3 pin XLR balanced mic signals. |
 |
C2035 NEW
|
|
|
|
A durable weather resistant horn speaker designed for use in conjunction with the Merlaud IP communicator PA system. It features an in-built amplifier and can be powered by 12-24V DC power supply or PoE as required. The sturdy mounting bracket is u shaped and secured with stainless steel hardware. |
 |
A4660A NEW
|
|
- Standard Features:
- Touch control paging with pre and post announcement chime options.
- Adjustable microphone automatic gain control (AGC).
- High quality electret microphone with high ambient noise control and feedback rejection.
- Adjustable backlight brightness and dimmed brightness levels with selectable timeout period.
- All glass front bezel for a stylish finish for any room.
- Connects via economical Cat5e UTP cabling.
- For long cable runs (approx. 200m+) we recommend using our A 4658 Power Injector.
|
|
This paging console is designed to provide general paging to zones when connected to a variety of Redback products. It provides a visual indication of the status of all audio sources and zones within the system at a glance, sharing a common screen with the master wallplates available for use with these systems. |
 |
A4427A NEW
|
|
- Eight input channels
- Micro SD card message player for audio announcements
- Individual level, bass and treble control on all inputs
- Six levels of VOX priority
- Adjustable VOX sensitivity
- Alert and Evacuation override mode
- 3.5mm music input
- Adjustable input sensitivity on line inputs
- 24V DC battery back up terminals
- In built Alert/Evac/Chime functionality
- 24V DC output
- MP3 active indicator
- LED VU meter
- 10 Year Warranty
- Australian Designed and Manufactured
|
|
This unique Redback PA mixer features four input channels which are user selectable for either balanced mic, line or auxiliary use. In addition it incorporates a four channel SD card based message player making it an excellent choice for retail, supermarkets, hardware stores and more. |
 |
SL4578BT NEW
|
|
|
|
This 12.8V 120Ah lithium battery (LiFePO4) is compatible in size with traditional 90-130Ah SLA batteries (check dimensions), but with all the benefits of cutting edge lithium technology with Bluetooth. |
 |
H1245 NEW
|
|
|
|
Chrome Plated Brass. Tapped to suit metric M3 machine Screws
Pack of 1000pcs. M3 x 25mm. |
 |
A4223 NEW
|
|
- Modular design allows for mix and match amplifiers within 1RU rack space.
- Class-D design with excellent performance and efficiency.
- LED indicators for protection mode, clipping condition and signal presence.
- 100V line or 8 ohm output via screw terminals.
- Stereo RCA line input.
- Balanced line input via 3 pin Euroblock pluggable terminal.
- High pass filter at 180Hz -3dB.
- Built-in short circuit, overload and high temperature protection.
- 2 year warranty.
|
|
This 2 x 240W PA zone amplifier developed by Redback, allows installers to mix and match amplifiers within a 1RU 19” rack space. |
 |
A4224 NEW
|
|
- Modular design allows for mix and match amplifiers within 1RU rack space.
- Class-D design with excellent performance and efficiency.
- LED indicators for protection mode, clipping condition and signal presence.
- 100V line or 8 ohm output via screw terminals.
- Stereo RCA line input.
- Balanced line input via 3 pin Euroblock pluggable terminal.
- High pass filter at 180Hz -3dB.
- Built-in short circuit, overload and high temperature protection.
- 2 year warranty.
|
|
This 480W PA zone amplifier developed by Redback, allows installers to mix and match amplifiers within a 1RU 19” rack space. |
 |
K8615 NEW
|
|
- 7.9" 4K mono LCD
- Self-developed integral light source
- High performance mainboard
- Z-axis with dual linear rails
- 5" HD touch screen
- Air filtration system
- Multiple slicing software
- Supports Creality Cloud APP
- Supports OTA updates
- Compatible with HALOT-BOX Lychee and CHITUBOX
|
|
The large 7.9" 4k mono LCD screen with a resolution of 4320*2560, vividly prints out every detail. With an upgraded 172 x 102 x 160mm build volume, it has a 73% volume increase compared to the 6" LCD and supports both smaller or larger models. |
 |
C0897 NEW
|
|
- Nominal Power (100V): 20W
- Maximum Power: 30W
- Frequency response: 80- 20000Hz
- SPL (max)1W@1m: 92-(105) dB
- Impedance: 0,5/1/2KΩ
- Power Selection (100V): 20/10/5W
- Connection: Terminal
- Dimensions: 170W x 280H x 160D mm
|
|
This speaker and microphone system is designed as a complete IP based communications package for the classroom with Bluetooth audio connectivity and 2.4GHz wireless microphone capability. |
 |
M8004 NEW
|
|
- Isolated design for maximum electrical safety
- Pure sine wave output
- Automatic AC transfer
- RCD Safety Switch
- Certified to Australian Standard AS/NZS 4763.2011
- DC/AC isolated design
- Safety authority tested for reliable & safe operation
- Over temperature, over voltage, over load and short circuit protection
- Low voltage cut off
- Excellent voltage regulation
- Binding post connection to battery
- Temperature controlled cooling fan.
|
COMING SOONThis item is arriving soon. |
This Powerhouse BlackMax inverter delivers a pure sine wave AC output, ideal for powering demanding loads. Fitted with integrated automatic AC transfer switch ensures seamless switching between mains and inverter power, providing uninterrupted operation for connected appliances.
|
