|
Description |
Downloads |
Specs |
Ordering |
|
 |
Z6589 |
|
- Intuitive output: Air Quality Index
- Measures VOCs and eCO2
- A great guide to get you started
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
- Manufactured and supported in Australia by Core Electronics
|
|
PiicoDev ENS160 Air Quality Sensor. Measure indoor air-quality - sensitive to fumes, cooking smells, humans. |
 |
Z6590 |
|
- Connect new sensors to your Micro:bit
- No soldering necessary
- Crocodile clip connections are broken out again, so you can still hand wire to your Micro:bit
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
|
|
Connect your Micro:bit with the outside world using PiicoDev® Adapter for Micro:bit. With this adapter you can experiment with sensors from the PiicoDev range giving your Micro:bit new sensing abilities. |
 |
Z6591 |
|
- Rapid prototyping with solderless connections
- Other useful pins are broken out
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
|
|
The PiicoDev® Adapter for Raspberry Pi is a great way to connect sensors to your Raspberry Pi. |
 |
Z6596 |
|
- 100mm long
- Also compatible with Qwiic and STEMMA QT boards
- Reversible cable - if it fits it works!
|
|
This 100mm cable is for connecting PiicoDev modules together. |
 |
Z6597 |
|
- 200mm long
- Also compatible with Qwiic and STEMMA QT boards
- Reversible cable - if it fits it works!
|
|
This 200mm cable is for connecting PiicoDev modules together. |
 |
Z9950 |
|
|
|
Handy stickers for your Atmega328p chips. Great for reminding you of the appropriate pinouts for your DIY Arduino prototype. Printed on quality Arlon UV vinyl.
|
 |
ZA6319 NEW
|
|
- Large 3-digit display of measured temperature
- Operates in both a heating and cooling mode of operation
- Programmable settings for temp set point, temp hysteresis, compressor delay and temperature calibration.
- Waterproof NTC temperature sensor has -50 to +99.9°C measurement range with ±1°C accuracy
- Over temperature and sensor failure audible and visual alarm
- Unit temperature reading can be calibrated
- Relays switch up to 120/240VAC @ 10A or 15VDC @ 10A
- 24VDC module operation
|
|
The STC-1000 temperature controller is a self contained heating / cooling controller that operates on 24VDC and controls either AC or DC loads up to 10A max current. |
 |
ZA6421 NEW
|
|
- Ultra compact form factor
- Dual core ARM Cortex M0+ processor
- Two SPI controllers
- Two I2C controllers
- 16 PWM channels
- 26 multifunction GPIO pins
- Three analogue inputs
- On board USB controller
- In-built temperature sensor
- Castellated module allows soldering direct to carrier boards
- Drag-and-drop programming using mass storage over USB
- Low-power sleep and dormant modes
- Accurate on-chip clock
- Accelerated integer and floating-point libraries on-chip
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2350, a brand new microcontroller chip designed by Raspberry Pi in the UK. From controlling appliances to operating a light display, Raspberry Pi Pico puts the technology that underpins countless everyday operations into your hands. |
 |
ZB6319 NEW
|
|
- Large 3-digit display of measured temperature
- Operates in both a heating and cooling mode of operation
- Programmable settings for temp set point, temp hysteresis, compressor delay and temperature calibration.
- Waterproof NTC temperature sensor has -50 to +99.9°C measurement range with ±1°C accuracy
- Over temperature and sensor failure audible and visual alarm
- Unit temperature reading can be calibrated
- Relays switch up to 120/240VAC @ 10A or 15VDC @ 10A
|
|
The STC-1000 temperature controller is a self contained heating / cooling controller that operates on 110-220V AC and controls either AC loads up to 10A max current. |
 |
ZR6302G |
|
- On board on/off power button
- Integrated fan control forthermal management
- Dual-display support
- Two micro-HDMI ports
- Supports display resolutions up to 4K @ 60hz (1 x 2K up to 1440P@60, 1 x 4K 2.0 up to 4k@60)
- Multiple connectivity capabilities so less add on hardware required, including Bluetooth 5.0 with BLE, Gigabit Ethernet & Wireless LAN
- A 40P GPIO expansion header provides extensive compatibility with a wide range of accessories
- Get more multiple memory options, including 4GB RAM and a speed eMMC socket
- Compatible with most R-Pi 4 accessories, including cases, cameras and HAT modules
|
|
The OKdo ROCK 4C+ is a reliable, multifunctional and high-performing single-board computer based on a robust Rockchip RK3399T SoC, Dual Cortex® A72 CPU and Arm Mali™ T860MP4 GPU. |
 |
ZR6474 |
|
- Cable Type: MIPI CSI Adapter Cable
- Cable Length: 0.1m
- Colour: Orange
|
|
Connect your ROCK board to a camera module with this MIPI CSI Camera Adapter Cable. |
 |
ZR6479 |
|
- Cable Type: MIPI DSI Adapter Cable
- Cable Length: 0.1m
- Colour: Orange
|
|
Connect a MIPI display to a ROCK single board computer with this MIPI DSI Display Adapter Cable. |
 |
ZW6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- HID support for keystrokes and mouse movement.
- Wi-FI and Bluetooth connectivity on board.
- Qwiic connector for I2C compatible sensors and actuators.
- LED matrix on board.
- Supports battery powered RTC.
|
|
The Funduino UNO R4 with WiFi is an Arduino compatible board integrating the powerful RA4M1 microcontroller with the robust wireless capabilities of the ESP32-S3 from Espressif. Additionally, it features an on-board 12x8 LED matrix, a Qwiic connector, a VRTC, and an OFF pin, making it an ideal choice for all your maker projects. |
