|
Description |
Downloads |
Specs |
Ordering |
|
|
Q1134A |
|
- New type holster, streamlined design, comfortable handle
- Large LCD display makes reading clear
- Strong antimagnetic and anti‐ interferential performance
- Auto power off when there is no measurement in 15 minutes
- Full function protection
- Unit symbol display, easy to read
- True RMS, non‐ contact voltage detect (NCV) and data hold function
- Lighting function, backlight display.
|
|
An affordable, versatile multimeter designed for the electronics enthusiast or handyman. |
|
Q1135 |
|
- Large easy read 19999 count screen
- Auto ranging
- True RMS measurement
- Data hold, min/max and relative modes
- Continuity buzzer
- Diode test
- Non contact AC voltage detection
- 2x AA battery included
|
|
This professional digital multimeter offers extended resolution to 4 digits! |
|
Q1150B |
|
- High accuracy inductance & capacitance ranges
- Jumbo 1999 count readout
- Battery included
- Supplied with quality silicon rubber test leads, rubber holster.
|
|
This dedicated LC meter offers wider inductance and capacitance ranges than other "do-it-all" meters available on the market. |
|
Q1242A |
|
- 200MΩ and 2000MΩ ranges
- Backlit LCD readout
- “Push to test” activation
- Auto power off
- Rubber holster
- Data hold
- High quality PVC leads
- Alligator clip lead adaptors
- Battery included
- Cat II 600V
|
|
Digital insulation testers measure the electrical insulation strength between two conductors by applying a high voltage across them and measuring any current that flows. This is to test for "leakage" paths and insulation breakdown in electrical circuits. |
|
Q1255A |
|
- Use on wood, wall board, sheet rock, cardboard, plaster, concrete, mortar and more
- Big backlit LCD display
- Replaceable electrode pins
- 2-in1 Digital LCD readout and analog bargraph
- Simultaneous measurement, display of moisture and temperature readings
- Materials selection measurements
- MAX/MIN/DATA hold
- Auto power off
|
|
Designed to measure moisture in wood and building materials this handheld meter can test levels in sawn timber, plaster, concrete, mortar and many other hard materials. |
|
Q1264A
|
|
- Ranges: Lo: 30 - 80dB
- Hi: 80 - 130dB
- Resolution: ±0.1dB
- Freq. range: 31.5Hz - 8000Hz
- Dynamic range: 50dB
- Freq. weighting: A & C
- Accuracy: ±1.4dB
- Microphone: Electret condenser
- Dimensions: 252H x 66W x 33D mm
|
|
A must for the serious audio installer or enthusiast. This quality sound pressure level meter gives a digital readout of the ambient noise level at its microphone. Features two ranges: Low (30 to 80dB) and High (80 to 130dB), with two built-in weighting curves. A and C weighting. Response can be switched between slow (1s) or fast (125ms). Features |
|
Q1266 |
|
- Ranges: 40-130dB
- Resolution: ±0.1dB
- Freq. range: 31.5Hz - 8000Hz
- Freq. weighting: A
- Accuracy: ±3.5dB
- Microphone: Electret condenser
- Battery: 9V (included)
- Dimensions: 130H x 52W x 32D mm
|
|
Compact pocket sized SPL meter for general purpose sound level measurement. The wide 40 to 130dB range is ideal for occupational health and safety testing in venues, industrial environments, car audio and home theatres. Fast response time with min/max function. LCD backlight switches on automatically when working in dark areas. Includes threaded in |
|
Q1278B NEW
|
|
|
|
A handy fast reading digital thermometer suitable for a wide array of uses such as monitoring liquids in laboratory, kitchen or BBQ use - great for roasting meats home brew setups and more! |
|
Q1283A |
|
- IR temperature range: -50 to 580°C
- IR resolution: 0.1 deg up to 580°C
- Emissivity: Adjustable 0.1-1.0
- Basic accuracy: ±2% of reading
- Distance-to-spot ratio (optical resolution): 13:1
- Spectral response: 8-14μm
- Dimensions: 155H x 98W x 27Dmm
|
|
This handheld IR thermometer offers laser pointer guide and excellent accuracy between -50°C and 580°C. |
|
Q1300 NEW
|
|
- Adjustable alarms for high/low pressure, temperature
- Leak detection
- Temperature monitoring
- Solar powered dash display
- Sticky dash mount allows for mounting anywhere
- Includes 4 matched sensors, USB cable, valve stem nuts and fitment wrench
|
|
This wireless monitoring system displays tyre pressure and temperature for your vehicle or trailer. The wireless sensors screw onto the valve stems of your tyres and transmit back to the solar powered dash monitor. |
|
Q1302 NEW
|
|
|
|
This signal booster for the Q1300 wireless TPMS allows you to increase range by relaying the sensors from your caravan or other trailer back to the internal monitoring unit in the vehicle. Requires 12V DC power. Bare end connection provided. |
|
Q1340B NEW
|
|
- Single way to test plug crimping quality
- Wire tracing & cable mapping at the same time
- Easily locate the port with a flashing signal
- PoE switches & STP wire tracing up to 3KM
- Telephone line status/polarity indication
- Cable mapping & status indication up to 300M for continuity, shorts, opens and crossover
- Fast/slow scan function
- Display cable status and troubleshoot wiring
- Non- contact voltage detecting
|
|
This Noise-Filtering Network PoE Toner & Probe allows users to quickly locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45, Lan cable Cat5, 5e, 6 (UTP/STP), RJ11/12 telephone cable Cat. 3 (2/4/6 pin) & normal solid/stranded wire by alligator clips patch cord. |
|
Q1341 |
|
- Headphone socket (earphones included)
- Adjustable buzzer volume
- Tests network and phone circuit voltage
- LED light on probe
- Single or dual tone
- Verifies short, open or crossed pairs in UTP cables
- Confirms integrity of patch leads and field wiring
- Includes RJ45 lead & croc clip test lead
|
|
Combines the functionality of a cable tracer and network cable tester in one convenient unit. The main unit can be connected to an unidentified pair which injects an audible signal down the line. |
|
Q1344 |
|
- Cable length measurement, accurate to ±3%
- Short circuit, open, split pair detection
- UTP cable conductor verification
- Includes USB charging lead
- Internal lithium ion battery in main unit
- Bright display backlighting
- Auto power off
- Confirms integrity of patch leads and field wiring
- Suits RJ11 and RJ45 cabling
- Adjustable buzzer volume
|
|
This compact handheld cable verifier features a USB rechargeable lithiumion battery for easy recharge on the go. It verifies the length and integrity of coaxial and UTP data/telephone cabling. It's wiremap system detects short circuits, split pairs and cable length up to 350m. |
|
Q1346 |
|
- POE test
- PING test
- Perform crosstalk test on network cable
- Test open, short or cross connection
- Measure length of telephone, network cabling up to 2000m
- Log data and measurements to internal Micro SD card
- Locate breakages
- Voltage detector in receiver end (50-1000V)
- Includes 8 remote units
- Voltage presence detection
- Includes carry case, charging lead and adaptors.
|
|
This comprehensive cable testing kit consists of three units. The main tester with 2.8" LCD screen, cable "sniffer" receiving unit and 8 remote identifiers. It is capable of measuring cable length, tracing cable location, continuity testing, PoE and Ping testing. It can be used with LAN, telephone cabling. |
|
Q1347A |
|
- Test open, short or cross connection
- Measure length of telephone, network cabling up to 1000m
- Detect length with or without remote units connected
- 3% accuracy (±0.5m)
- Locate breakages
- Includes 8 remote units
- Includes carry case, 2 x 9V batteries, earphones, charging lead and adaptors
|
|
This comprehensive cable testing kit consists of three units. The main tester with 4 x 16 character screen, cable ‘sniffer’ receiving unit and 8 remote identifiers. |
|
Q1360 |
|
|
|
This pocket tester detects DC continuity and short circuits in coaxial leads and cable runs. It provides LED and audible feedback when testing is complete ensuring connection integrity. Fitted with male F connector, may be combined with many other adaptor |
|
Q2007 NEW
|
|
- Suitable for 50V, 70V and 100V line speaker systems up to 5kW
- Also suitable for measuring low Impedance speaker loads of 4 -16Ω
- OLED display shows Impedance and Wattage of the load
- 1Ω to 20KΩ test range
- Auto ranging
- Display accuracy +/-10%
- Push button operation
- System Check Mode (20, 60 or unlimited minutes)
- 5V Rechargeable Lithium Polymer internal battery
- Low battery indication
- Buzzer and Haptic feedback option via Menu access
- USB Charging lead supplied
- Silicon Test Leads supplied
- Soft Carry Case Included
- Rugged yet easy to hold compact hand held case
|
|
An absolute necessity for all PA system installers. This impedance meter for ‘dummies’ designed and manufactured by Altronics calculates and displays speaker loads in watts. Lithium rechargeable version. |
|
Q2014 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
|
|
Compact and portable, this handheld battery powered 1KHz tone generator has been designed to test PA systems and in particular hearing loop induction sound systems. The unit produces a 1KHz tone which is fed into the input of the amplifier under test. Two output levels are provided, 100mV and 1V. Includes 9V battery. Size: 79W x 117H x 24Dmm. |
|
Q2022A NEW
|
|
- All metal construction
- Portable design runs off 9V battery (sold separately)
- Easy to use cable integrity checker for PA and AV installers
- New model supports Powercon and 3.5mm jacks
|
|
Compatible with 3.5mm jack, 6.35mm jack, 3/5/7/8 pin DIN, RCA, 3/5 pin XLR, 4P Speakon, Powercon, banana plugs, RJ45 and USB. A quick and easy way to confirm lead integrity. |
|
Q2100 |
|
- Connect any way round.
- Automatic component type identification.
- Automatic pinout identification.
- Transistor gain measurement.
- MOSFET gate threshold measurement.
- PN junction characteristics measurements.
- Leakage current measurement.
- Auto power on and power off.
- Ultra-slim and compact design.
|
|
An amazingly versatile piece of test equipment that could save you hours in looking up transistor, diode and FET specifications!
Once you've used the Atlas Component Analyser, you'll wonder how you ever did without it. |
|
Q2105 |
|
- Measure ESR (even in-circuit).
- Measure capacitance (from 0.3μF to 90,000μF).
- Automatically starts analysis when the ESR70 is connected.
- Audible alerts with different tones for various ESR levels.
- ESR resolution down to 0.01Ω.
- Polarity free due to bi-directional low voltage (500mV) test span.
- Low DC resistance checking measurement (even in-circuit).
- Supplied complete with 2mm male test leads and 2mm compatible gold plated crocs.
- Test leads are ultra-durable and 45cm (18") long with 2mm plugs.
- Enhanced software compensation of cable resistance.
- Enhanced compensation for leakage or parallel resistance.
- Improved LCD with better backlight.
- 10x faster capacitance measurement for large capacitors.
- Enhanced user options system.
- New triple-slope measurement system to vastly reduce the influence of parallel resistance and/or leakage current on capacitance measurements.
- Much wider capacitance measurement range now 0.3μF to 90,000μF (was 1μF to 22,000μF).
|
|
Measuring a capacitor's ESR (equivalent series resistance) is a great indicator of capacitor condition. The Atlas ESR offers instant results. Just connect the probes and press test - no need to worry about polarity! You can even use the Atlas ESR in circu |
|
Q2112 |
|
- Resistance: 1Ω-2MΩ (±0.1Ω/1%)
- Capacitance: 0pF-10,000µF ( ±0.1pF/1.5%)
- Inductance: 0µH-10H ( ±0.1µH/1.5%)
- Peak test voltage (OC): -1.05V / +1.05V
- Peak test current (Silicon Chip Magazine): - 3.25mA / +3.25mA
- Test frequency accuracy: ±1%
- Sine purity: Typically -60dB 3rd harmonic
- Dimensions: 100 x 70 x 20mm
|
|
The Atlas LCR analyser is an advanced tester which greatly simplifies the testing of passive components. Simply connect the hook probes to the component legs and press test. In seconds the Atlas LCR will identify the type of component (inductor, cap |
|
Q2115 |
|
- The DCA Pro is an advanced new design that includes a graphics display, USB port, PC Software and an enhanced component recognition library.Transistors (including Darlingtons and "digital" transistors), Silicon and Germanium types. Measures gain, VBE and leakage.
- MOSFETs, enhancement mode and depletion mode types. Measure on-threshold (at 5mA) and approx transconductance (for span of 3mA-5mA).
- JFETs, including normally off SiC types. Measures pinch-off voltage (at 1uA) and approx transconductance (for span of 3mA-5mA).
- IGBTs (insulated gate bipolar transistors). Measures on-threshold (at 5mA).
- Diodes and Diode networks.
- LEDs and bicolour LEDs (2 lead and 3 lead types).
- Zener Diodes with measurement of zener voltage up to 9V at 5mA.
- Voltage regulators (measures regulation voltage <8V, drop-out voltage, quiescent current). Note that some regulators are not stable without their decoupling caps and/or minimum load and cannot be tested by the DCA75.
- Triacs and Thyristors that require less than 10mA of gate current and holding current.
|
|
Our all new Peak Advanced Semiconductor Analyser will
Automatically identify part type (eg, Transistor, JFET, IGBT, Regulator, Zener, Diodes, etc). Automatically identify pinout (connect any way round).
|
|
Q2118 NEW
|
|
- Large easy to read LCD display with backlighting.
- Tests battery CCA, voltage, internal resistance, battery health and charge status.
- Provides "Good Battery", "Good Recharge", "Charge Retest", "Replace", "Bad Cell Replace" condition statuses.
- Supports all battery standards, JIS, DIN, IEC, EN, SAW, CA, CCA, GB, BCI, MCA.
- Short circuit and reverse polarity protection.
- Test history display.
- Tests batteries in-situ in vehicle or out of vehicle.
- Quick test function via AH input.
|
|
Detects and analyses battery voltage, cold cranking amperes (CCA), resistance (mΩ) and battery cell condition. |