|
Description |
Downloads |
Specs |
Ordering |
|
 |
Q0203B NEW
|
|
- 2 Channel Digital Oscilloscope + Arbitrary/Function Waveform Generator + Synchronising Signal + External Trigger
- Easy to use button layout
- Large and clear 7” true colour 24-bit display
- Oscilloscope: 1GSa/s Sample Rate, 100MHz Bandwidth
- Huge selection of auto measurement functions
- Powerful trigger functions: Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC
- Arbitrary/Function Waveform Generator: 25MHz, 12 bits resolution, 200MHz DDS, Arbitrary wave/square wave/sine wave/triangle wave/trapezoidal wave/pulse wave/DC
- Integrated USB host, support USB disk storage, USB interface system update
|
|
Perfect for those in R&D, product development or service of complex electronic equipment. This compact bench top oscilloscope features 2 channels with real-time sampling modes of 1GSa/s (25GS/s equivalent sampling rate). |
 |
A3607 NEW
|
|
- 1080p @ 60Hz wireless video and audio
- Casts a HDMI source device to a monitor or television up to 50m away
- Operates on 5GHz 802.11ac band
- HDMI 1.4 compliant
- HDCP compliant
- Fully automatic pairing for near instant signal connection
- No drivers, software, manual casting or set up needed.
|
|
These wireless extension cables provide a simple way to send 1080p 60Hz signals from a HDMI source device to TV or monitor in another room up to 50m away (line-of-sight). |
 |
Z6302K NEW
|
|
- Broadcom BCM2712 quad-core Arm Cortex A76 processor @ 2.4GHz
- RAM variants up to 8GB
- Interchangeable Camera and DSI display connectors
- Dual 4Kp60
- Real-time clock
- Power button
- UART debug port
|
|
The Raspberry Pi 5 8GB single board computer. The bandwidth speed and performance of the new Raspberry Pi 5 is a step up from earlier models. |
 |
P8166 NEW
|
|
- 240V AC 10A outputs.
- 7 x Australian Sockets (AS/NZS 3112:2017 conforming).
- Electrical authority outlet device approved (AS/NZS 3105:2014 conforming).
- High surge protection.
- Overload protection.
- Power cord located at the rear for less interference.
- 19” rack ear mounting.
|
|
The neat solution to supplying mains power to your mounted equipment. |
 |
Q2007 NEW
|
|
- Suitable for 50V, 70V and 100V line speaker systems up to 5kW
- Also suitable for measuring low Impedance speaker loads of 4 -16Ω
- OLED display shows Impedance and Wattage of the load
- 1Ω to 20KΩ test range
- Auto ranging
- Display accuracy +/-10%
- Push button operation
- System Check Mode (20, 60 or unlimited minutes)
- 5V Rechargeable Lithium Polymer internal battery
- Low battery indication
- Buzzer and Haptic feedback option via Menu access
- USB Charging lead supplied
- Silicon Test Leads supplied
- Soft Carry Case Included
- Rugged yet easy to hold compact hand held case
|
|
An absolute necessity for all PA system installers. This impedance meter for ‘dummies’ designed and manufactured by Altronics calculates and displays speaker loads in watts. Lithium rechargeable version. |
 |
S9721A NEW
|
|
- USB to RS485 communication
- Adopt original FT232RL and SP485EEN, fast communicating, stable and reliable, better compatibility
- Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightning-proof & anti-electrostatic
- Onboard self-recovery fuse and protection diodes, ensures the current/voltage stable outputs, provides over-current/over-voltage proof, improves shock resistance
- 3 LEDs for indicating the power and transceiver status
|
|
The USB TO RS485 is very easy to use, allows automatic transceiving. Due to its fast communication, stability, reliability, and safety, it is an ideal choice for industrial control equipments and/or applications with high communication requirement. |
 |
Z6317 NEW
|
|
- 3-digit display of temperature
- Module can operate in a heating or cooling mode of operation
- Multiple parameters can be set such as temp trip point, hysteresis and delay.
- Waterproof NTC temperature sensor has -30 to +110°C measurement range with 0.1°C accuracy
- Relay switches up to 120VAC @ 10A or 14VDC @ 10A
- 12V module operation
|
|
This high precision temperature control module is a highly functional self-contained temperature controller module for both heating and cooling applications. |
 |
T1345 NEW
|
|
- Remove dust and debris from your car.
- Get dirt and dust from nooks and crannies around your home.
- Easy USB C recharging for up to 1.5 hours use per charge.
- Adjustable fan speeds for delicate tasks or heavy duty cleaning.
- Great for cleaning keyboards, removing dust from PC's and other equipment.
- Pairs with T1346 for vacuum function.
- Removeable nozzle with 32mm thread.
- Can be used as an inflator when paired with well fitted nozzle (see sizes in specifications).
|
|
This lithium USB rechargeable jet blower fan makes cleaning a breeze! The lightweight aluminium housing delivers a blast of wind for cleaning and inflating tasks. |
 |
A3245 NEW
|
|
- Extend both HDMI signal plus USB peripherals.
- Transmission up to 70m over Cat6/6a UTP cabling.
- Ideal for remote operation of PC equipment.
- HDMI 2.0b, HDCP 2.2 compliant.
- 18Gbps video bandwidth.
- EDID management.
- Includes transmitter & receiver.
- Supports USB 1.1 KVM pass-through.
|
|
This product is designed to extend HDMI signals over distances up to 70m using Cat6/6a cabling. In addition it also allows USB peripherals to control a connected computer from the receiver end. |
 |
T1285A NEW
|
|
- Power: 320W
- Voltage: 220-240V 50Hz
- Air pump: Diaphragm pump
- Capacity: 24L/min (max)
- Hot air temperature: 160-480°C
- Sensor: K thermocouple
|
|
This re-work station provides a quick and easy way to rework boards fitted with surface mount devices. |
 |
C9021B NEW
|
|
- Hybrid Active Noise Cancelling
- Be heard loud and crystal clear with FutureTour. The device is shielded with proprietary technology that continuously monitors and measures outside noise and cancels it with the opposite signal. The advanced audio signal processing smartly eliminates the need for a mic arm and reduces background noises.
- Long Play Battery
- FutureTour never kills your vibe. Offering you 40 hours of continuous playtime and amazes you with quick charging to continue listening all day.
- Crystal-Clear Call
- FutureTour features an advanced mic system with HD Voice that provides clarity in conversation.
- All-Day Comfort with Soft Fit Foam Cover
- Enjoy your music in comfort with a beautifully finished newly developed foam cover. FutureTour has the highest quality soft material that provides less pressure on the ears while keeping out external sounds.
- Built Better Sound
- FutureTour headphones deliver carefully balanced, high-fidelity audio for a quality listening experience.
- Faster connection and enhanced connection
- Experience faster and more stable connections with our wireless 5.2 technology, so you can move freely without any interruptions for an unparalleled wireless listening experience.
- Auxiliary Cable
- Running out of battery and you're almost on the way to reaching the finish line? FutureTour gives you an add-on feature of aux cable connection so you can continue listening.
|
|
The Hifuture Futuretour headphones provide excellent noise canceling performance, allowing you to work and listen without interference from outside sources of noise. |
 |
T1534B NEW
|
|
- Crimps copper lug and non-insulated terminals
- Crimps Anderson plug terminals
- Designed with long handles for added leverage on thick walled terminals
- Removable handles for compact storage
- Rotating jaws for changing between crimp sizes
- Chrome plated finish prevents corrosion and protects against wear and tear
- Produces professional quality crimp work
|
|
Rugged cast steel crimper designed for uninsulated cable lugs and Anderson plugs. 6mm2 to 50mm2. Commonly used for making high current battery leads in solar installations. 387mm length. |
 |
S8864A NEW
|
|
- Sturdy adjustable back stand
- 1280x800 resolution
- USB PVR recording support
- HDMI input
- AV input
- HD tuner
- Headphone output
- SD card slot
- IR Remote control
|
|
A must have for your next caravan, boating or camping trip. This portable 14 inch TV allows you to enjoy high definition entertainment on the go thanks to its in-built lithium battery. |
 |
S8866 NEW
|
|
- HDMI input
- AV input
- 1080p Full HD tuner
- 1080p Full HD resolution 23.6” LED panel
- 3.5mm headphone output
- USB PVR recording support
- IR Remote control
- Ideal for 4WD’s caravans, boats and camper vans
- 240V AC (plugpack) or 12V DC operation
- VESA 75 x 75mm compatible mounting
|
|
This 23.6” wide screen TV is designed for 12V vehicles, 4WDs, caravans and campers. Full HD 1080p. |
 |
T5099 NEW
|
|
- Pre-wired for simple installation
- 6 rocker switches
- 3 car accessory sockets
- Dual USB. (2.1A/1A) charging ports
- Voltmeter
- 6 Way fuse lock with spare fuses
- Dual Anderson SB50 Style sockets for solar panel & battery
- 6 Cable entries
- Fused Input and output (30A)
- Durable ABS case
- Includes switch icons and word labels
|
|
A complete central power hub for your 4WD, caravan or camping remote power set up. This box contains 6 contura style illuminated switches, 3 car accessory sockets (12V), USB charger, LED volt meter, all protected by a 6 way weatherproof fuse block. |
|
Z6302J NEW
|
|
- Broadcom BCM2712 quad-core Arm Cortex A76 processor @ 2.4GHz
- RAM variants up to 8GB
- Interchangeable Camera and DSI display connectors
- Dual 4Kp60
- Real-time clock
- Power button
- UART debug port
|
|
The Raspberry Pi 5 4GB single board computer. The bandwidth speed and performance of the new Raspberry Pi 5 is a step up from earlier models. |
 |
X0235 NEW
|
|
- 3W 190 lumen main LED beam with 40m range.
- Adjustable focus beam.
- 80 lumen lantern light on side.
- Provides 2 hours use from 2 x AAA batteries.
- Anodized aluminium body.
- Built in pocket clip.
- Shock resistant design for drops up to 1m.
- Weighs just 45 grams!
|
|
Need a torch for your pocket while you work? This handy pen light provides all the light you might need with a powerful 3W, 190 lumen beam with up to 40m range. The front of the torch can be rotated to a focus and adjust the light beam as needed. |
 |
X7100 NEW
|
|
- Jumbo clock digits - read up to 30m away!
- Calendar display.
- Day of the week display.
- Temperature & humidity display.
- Programmable alarm with snooze function.
|
|
This handy jumbo LCD 12/24 hour clock, thermometer and calendar is great for around the home or office. The extra large clock digits allow it to be read up to 30m away. The screen also provides date, day of the week, temperature and humidity readings. |
 |
T1463 NEW
|
|
- Sturdy steel base with recesses for dry tip cleaner, rosin flux and cleaning sponge.
- LED magnifier provides a crisp clear view.
- Non-slip rubber feet on industrial powdercoated metal base.
- Powered by USB C - cable included.
- Solder reel holder in-built.
- 4 segmented arms which stay in place when positioned.
- Rubber tipped spring clamps secure your parts in place while working.
- Includes dry tip cleaner, container of rosin tip flux, cleaning sponge and USB A to C power cable.
|
|
This handy bench top helper features an LED magnifying lamp, plus 4 flexible arms for keeping items in position when working on them, making it ideal for soldering cables, PCBs and a range of hobbyist uses. |
 |
Z6296 NEW
|
|
|
|
Get your brand new Raspberry Pi Zero 2 W with most of the essentials in this kit. |
 |
X2920 NEW
|
|
- Compact, low profile design
- Rugged aluminium housing
- Weatherproof IP68 rated
- Suitable for both 12V and 24V applications
- 3 x 5W high brightness LED chips
|
|
DC vehicle lighting for 4WD's, boats, trucks and trailers. Rugged aluminium casing and ultra bright light output. |
 |
M8196 NEW
|
|
- 83Wh internal lithium-ion battery (22.5Ah @ 3.7V)
- Light weight yet sturdy design with carry handle
- Micro USB recharge port
- USB C PD 18W output
- Dual QC3.0 18W USB A outputs
- 5W max hand crank recharging
- Torch with SOS mode
- Three brightness lantern/reading lamp
- Recharge time 4.5hrs (QC3.0).
- Battery capacity readout
|
|
Great for camping and hiking getaways, this compact portable charging solution keeps your devices powered up while also providing a handy lamp and torch. |
 |
K8600A NEW
|
|
- Simple set up - get printing within 20 minutes.
- Worry free automatic levelling.
- Easy to understand user interface with colour display.
- Auto filament loading and unloading.
- Direct extrusion for most common filament types.
- Ultra stable design with rigid dual Z-axis.
- Compact design fits easily on the workbench.
- Standard 0.4mm nozzle.
- 220 x 220 x 250mm build volume.
|
|
The Ender-3 V3 SE 3D printer is an enhanced and upgraded version of Creality's hugely popular Ender 3 platform. Creality have built in more features and optimisation for an intuitive and efficient FDM 3D printing experience. This Ender 3 has been tailored for those wanting a no compromises approach to features. |
 |
D0520 NEW
|
|
- High 65W output for high capacity devices such as laptops
- 20,000mAh capacity
- 74Wh capacity - OK for air travel
- USB type A and type C outputs on front panel
- Study aluminium casing.
|
|
This 20,000mAh battery bank offers high output Power Delivery (PD) allowing users the ablity to charge a range of devices. It features an aluminium casing with power capacity LCD readout. Dual USB type A outputs as well as dual USB C PD outputs. |
 |
Z6433 NEW
|
|
- XTensa dual-core 32-bit LX7 CPU, frequency up to 240MHz
- 2.4 GHz Wi-Fi, EEE 802.11 b/g/n-compliant
- Bluetooth, LE: Bluetooth 5, Bluetooth mesh
- 16 MByte(64Mbit) SPI Flash
- 384 KByte ROM
- 512 KByte SRAM
- 8 MByte(64Mbit) SPI PSRAM
- 16 KB SRAM in RTC
- Communication Interfaces: 2 x I2C, 2 x I2S, 4 x SPI, 3 x UART, 1 x USB OTG
- Security: 4096 bit OTP, AES, SHA, RSA, ECC and RNG, Secure boot, Flash encryption, Digital signature, HMAC module
- Dual Type-C USB connectors
- Reset and User/Firmware buttons
- RGB WS2812 User LED
- Power LED
- Virtual USB port provided by CP2102 for debugging and firmware upgrade
- Compact size of 50.1 x 13mm
- Supply Voltage: 5V via USB
- Circuit Voltage: 3.0 to 3.6V Circuit Operation
|
|
The ESP32-S3 development board is assembled with an original ESP32-S3-WROOM-1 module from Espressif, with 16MB Flash and 8MB PSRAM(ESP32-S3-WROOM-1-N16R8). It is a general-purpose Wi-Fi + Bluetooth® LE MCU module that integrates complete Wi-Fi and Bluetooth LE functions. |
 |
Z6319 NEW
|
|
- Large 3-digit display of measured temperature
- Operates in both a heating and cooling mode of operation
- Programmable settings for temp set point, temp hysteresis, compressor delay and temperature calibration.
- Waterproof NTC temperature sensor has -50 to +99.9°C measurement range with ±1°C accuracy
- Over temperature and sensor failure audible and visual alarm
- Unit temperature reading can be calibrated
- Relays switch up to 120/240VAC @ 10A or 15VDC @ 10A
- 12VDC module operation
|
|
The STC-1000 temperature controller is a self contained heating / cooling controller that operates on 12VDC and controls either AC or DC loads up to 10A max current. |
 |
T2125 NEW
|
|
- 5000 to 25000 RPM in 5K RPM steps.
- Ideal for crafts, hobbies and odd jobs around the house.
- Compact design fits easily in the hand.
- USB type C recharging.
- Up to 1 hour use per charge.
- Spindle lock for easy change over of accessories.
- 42 accessories included.
- Snap lid carry case.
|
|
Drills, cuts, sharpens, cleans, polishes and engraves most surfaces, this rotary tool is ideal for enthusiasts, craft & hobby makers, or just odd jobs around the house. |
 |
A3608 NEW
|
|
- 1080p @ 60Hz wireless video and audio
- Casts from a USB type C device to a monitor or television up to 50m away
- Operates on 5GHz 802.11ac band
- HDMI 1.4 compliant
- HDCP compliant
- Fully automatic pairing for near instant signal connection
- No drivers, software, manual casting or set up needed.
|
|
HDMI wireless sender capable of sending 1080p 60Hz signals from your device to a TV or monitor in another room up to 50m away (line-of-sight). |
 |
D0521 NEW
|
|
- High 100W outputs for high capacity devices such as laptops
- 30,000mAh capacity
- 111Wh capacity (check with your airline for suitability for travel with carry on)
- USB type A and type C outputs on front panel
- Study aluminium casing.
- Torch with 3 modes on back panel
|
|
This 30,000mAh battery bank offers high output Power Delivery (PD) allowing users the ablity to charge a range of devices. It features an aluminium casing with power capacity LCD readout. Dual USB type A outputs as well as dual USB C PD outputs. |
 |
S4345 NEW
|
|
- Max DC switching: 75V @ 100A / 1400W
- Contact material: Silver alloy
- Coil resistance: 60Ω
- Max coil power: 2.4W
- Insulation resistance: >100MΩ @ 500V DC
- Dielectric strength (for 1 min): 500V AC between open contacts
- 750V AC between coil & contact
- Connection: (Coil 6.3mm & M6 bolt for contact load)
- Life: 100,000 operations electrical, 10 million mechanical
- Dimensions: ≈46W x 46L x 77H mm
|
|
Suitable for high current DC automotive applications. Not suitable for AC use. M6 bolt for contact load connection. 6.3mm spade terminals for contact coil connection. |
 |
X6017 NEW
|
|
- Reads trouble codes on most vehicles
- Displays general and vehicle specific codes
- View vehicle information
- View real-time data streams
- An essential automotive diagnostic tool
|
|
This OBDII code reader is used to check engines of all vehicles that comply with OBD II, 12V voltage with standardized 16-Pin connector. This OBDII scanner tool provides a complete solution for reading vehicle data on OBDII equipped vehicles. |
 |
P7780A NEW
|
|
|
|
A 3 pole DC plug in the style of the SB50 Anderson connector. |
 |
Q2022A NEW
|
|
- All metal construction
- Portable design runs off 9V battery (sold separately)
- Easy to use cable integrity checker for PA and AV installers
- New model supports Powercon and 3.5mm jacks
|
|
Compatible with 3.5mm jack, 6.35mm jack, 3/5/7/8 pin DIN, RCA, 3/5 pin XLR, 4P Speakon, Powercon, banana plugs, RJ45 and USB. A quick and easy way to confirm lead integrity. |
 |
Q1068A NEW
|
|
- Auto ranging with manual override
- Min/max & data hold
- Non contact AC voltage detector
- Frequency/duty cycle measurement
- Temperature measurement
- Backlit LCD screen with bargraph
- Diode test
- Continuity buzzer
- 3 x AAA Batteries included
- Auto power off
- Cat II 1000V, Cat III 600V
- 2 year warranty.
|
|
With in-built AC mains detection. This is one of the best digital multimeters we have evaluated when it comes to build quality and feature set. Its perfect for the serious enthusiast or tradesperson. LCD bargraph. 3.75 digit display. Mode assistance indicators. |
 |
A3605 NEW
|
|
- Supports 4K @ 60Hz.
- As low as 100ms latency.
- Supports 20-60KHz IR remote extension.
- Supports USB KVM function.
- Up to 150m transmission line of sight.
- Auto channel selection.
- Equipped with 802.11ac 2T2R WiFi MIMO module.
- High-security protection.
- Supports one transmitter to multiple receivers.
- Supports HDCP2.2
|
|
This 4K wireless HDMI extender system supports 4K 60Hz resolutions with super smooth playback and low latency. You can now watch TV in your bedroom, study or any other room without messy cables. |
 |
M8534B NEW
|
|
- Short circuit and reverse polarity protected
- Suitable for use with lead acid, LiFePO4, AGM/EFB batteries.
- Overheating protection
- Includes car accessory socket lead, battery clamps and ring terminal lead
- Suits 6V and 12V cells
- Defective cell detection
- Trickle charge function
- 12V DC 6A power supply mode
- IP65 rated
|
|
This compact charger is suitable for all lead acid type and Lithium (LiFePO4) type batteries. It will charge 6V/12V cells using a 6-stage charging circuit. |
 |
A0724 NEW
|
|
- Operating voltage: 12 V/DC (11 - 14 V)
- Power consumption: approx. 2 mA/35 mA (relay off/on)
- Relay contact: 1 x SWITCH OVER, loading capacity max. 25 V, 3 A
- Operating temperature range: approx. -15 to +50°C
- Luminous intensity switching-on: approx. 25 lux ±20%
- Luminous intensity switching-off: approx. 45 lux ±20%
- Switching delay: approx. 3 - 4 seconds
- Dimensions: approx. 72 x 50 x 32mm (without fastening straps, with sensor)
|
|
Kemo M122 switch allows users to switch lamps or other electric devices on or off at dusk or daybreak. The sensitivity of the luminous intensity may be changed by partially covering the sensor mechanically. |
 |
S4343 NEW
|
|
- Max DC switching: 75V @ 200A / 1500W
- Contact material: Silver alloy
- Coil resistance: 120Ω
- Max coil power: 4.8W
- Insulation resistance: >100MΩ @ 500V DC
- Dielectric strength (for 1 min): 500V AC between open contacts
- 750V AC between coil & contact
- Connection: (Coil 6.3mm & M6 bolt for contact load)
- Life: 100,000 operations electrical, 10 million mechanical
- Dimensions: ≈46W x 46L x 77H mm
|
|
Suitable for automotive applications such as alarms, driving lights, horns, fog lights etc. |
 |
S4737A NEW
|
|
- Nominal Capacity: 3500mAh (0.2C, 2.75V discharge)
- Minimum Capacity: 3350mAh(0.2C, 2.75V discharge)
- Charging Voltage: 4.2 ±0.05 V
- Nominal Voltage: 3.7V
- Charging Method: CC-CV (constant voltage with limited current)
- Charging Current: Standard charge: 1700mA
- Charging Time: Standard charge : 4hours
- Max. Charge Current: 2000mA (ambient temperature 25°C)
- Max. Discharge Current: 8A (continuous discharge)
- Discharge Cut-off Voltage: 2.65V
- Cell Weight: 50.0g max
- Cell Dimension: Height: 65.25mm max, Diameter: 18.55mm max,
- Operating Temperature: Charge: 0 to 45°C, Discharge: -10 to 60°C
- Storage Temperature 1 year: -20~25°C, 3 months: -20~45°C, 1 month: -20~60°C
|
|
These high performance 18650 lithium ion 3.7V batteries offer high performance and long life from a compact package. They are 18.6mm in diameter and 65mm long. |
 |
A0328 NEW
|
|
- Easy to install
- One receiver can pair with 8 transmitters
- One transmitter can pair many receivers, theres no limit
- Battery Operated
- 200m Operating Range: 200M in open air
- 52 melodies available
- 4-Level Volume Control
- LED Indicator
- IP56 Waterproof Push Button
- Auto Learning code
|
|
Provides up to 200m wireless range and 52 doorbell tunes so you always know when visitors arrive. 4 level volume control. IP56 rated doorbell button. Requires 23A battery for transmitter and 3 x AAA batteries for receiver. 433.92MHz frequency. |
 |
ZW6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- HID support for keystrokes and mouse movement.
- Wi-FI and Bluetooth connectivity on board.
- Qwiic connector for I2C compatible sensors and actuators.
- LED matrix on board.
- Supports battery powered RTC.
|
|
The Funduino UNO R4 with WiFi is an Arduino compatible board integrating the powerful RA4M1 microcontroller with the robust wireless capabilities of the ESP32-S3 from Espressif. Additionally, it features an on-board 12x8 LED matrix, a Qwiic connector, a VRTC, and an OFF pin, making it an ideal choice for all your maker projects. |
 |
Q1089 NEW
|
|
- True RMS Auto Range.
- Large easy to read reverse backlit screen.
- Simple push button operation.
- Large multifunction display.
- Indicates correct connection jacks.
|
|
This compact true RMS digital multimeter provides in depth functionality for technicians troubleshooting devices and circuits. |
 |
P8064 NEW
|
|
|
|
A handy gland cable entry point for caravans, campers and vehicles with roof mounted solar panels. Can be surface mounted using silastic or similar weatherproof adhesive. PG13.5 cable gland with 7.5mm cable entry (prior to tightening). Size: 60W x 112D x 35Hmm. |
 |
D2208A NEW
|
|
- Qi Wireless Charging
- Motorised to fit your phone automatically
- Comes with a USB Type C lead
- Safely use navigation apps in the car
- Air vent spring mount
- Suction cup mount
|
|
This 15 Watt Qi Wireless Charging Universal Phone Car Mount will not only charge your phone with its wireless fast charge feature but it will also allow you to safely use navigation apps in the car. |
 |
Q1058 NEW
|
|
- Large easy to read 20000 count screen
- Folding design stays stable on any surface
- Use it on the bench top or in the field
- Autoranging
- Handy automotive testing functions
- Non-contact AC voltage detection >90V AC
- Data hold, min/max relative modes
- In-built lithium battery pack - no batteries required!
- USB C rechargeable
- Temperature measurement (sensor included)
|
|
This folding autoranging digital multimeter provides in depth functionality for technicians troubleshooting devices and circuits. |
 |
S2692A NEW
|
|
- Continuous Rating: 275A at 12VDC (200A at max 50VDC)
- Cranking Rating: 1250Amps at 12VDC (1000A at max 50VDC)
- Terminal Size: M10
- Electrical Life: >10000 cycles
- Dimensions: 68 x 68 x 75 mm
|
|
Rotary on/off master switch for high current DC circuits and battery banks. |
 |
D2362A NEW
|
|
|
|
A handy 7 port USB 3.0 hub for those with lots of peripherals! Each connection has a dedicated on/off switch. USB type C power input with type A connection to your computer. |
 |
M8536B NEW
|
|
- Short circuit and reverse polarity protected
- Suitable for use with lead acid, LiFePO4, AGM/EFB batteries.
- Overheating protection
- Includes car accessory socket lead, battery clamps and ring terminal lead
- Suits 6V and 12V cells
- Defective cell detection
- Trickle charge function
- 12V DC 10A power supply mode
- IP65 rated
|
|
This compact charger is suitable for all lead acid type and Lithium (LiFePO4) type batteries. It will charge 6V/12V cells using a 6-stage charging circuit. |
 |
Z6316 NEW
|
|
- Easy to set up and pair - Android app available for direct control.
- Onboard Bluetooth status indicator and relay indicator.
- With 2 optocoupler isolation, strong anti-interference ability.
- Onboard N76E003/STM8S003 and SPP-C Bluetooth 2.1 module.
- Compact board design.
- Module with diode effusion protection short response time
|
|
A combined relay and control board with the ability to switch on and off connected loads using an App on your phone via Bluetooth. The eWeLink app offers seamless power switching using your device when in range of the relay board (typically 10m). |
 |
M8561A NEW
|
|
- 88% efficient switchmode power supply design.
- Protections: overload / over voltage / short circuit / under voltage / reverse polarity.
- 5A max connected load. 650mA battery charging circuit.
- LEDs provide quick status indication.
- Fits a standard size 7.2Ah 12V SLA battery.
- Patented design with simple wall mount installation.
- 100% full load burn-in tested.
- 2 year warranty.
|
|
A complete 12V DC power supply and UPS battery backup in one compact enclosure. When operating from 240V, it automatically charges the internal battery (available separately) and powers the connected load (max 5A). |
