|
Description |
Downloads |
Specs |
Ordering |
|
 |
A4831 |
|
|
|
Interfaces 2 input and 4 output CSP UTP wallplates with Dante® systems |
 |
A4830 |
|
|
|
Interfaces 1 input and 1 output CSP UTP wallplates with Dante® systems. |
 |
A4816 |
|
- Four Mic/Line XLR Inputs on Front Panel
- Terminal Block for Two Audio Outputs on Rear Panel
- Converts Mic or Line Audio Signals to Dante network
- Mic or Line is Selectable for Each XLR Input
- Switchable 48V Phantom Power for Each Mic XLR Input
- Adjustable Mic/LIne Gain from ‐20 dB to +20dB for Each XLR input (Two Audio Signal Outputs from Dante Network)
- Balanced or Unbalanced Signal Outputs
- High Resolution 24 Bit for DAC and ADC
- Power over Ethernet (PoE) or 24VDC power supply
- Provides High Quality of Preamplifier for microphones
- Excellent Audio quality with low noise
|
|
Dante Interface 4 x Mic/Line Inputs, 2 x Line Outputs |
 |
A4818 |
|
- Two Mic/Line XLR Inputs and one mini-jack input on Front Panel
- Terminal Block for Two Audio Outputs on Rear Panel
- One mini-jack output on front panel
- Converts Mic or Line Audio Signals to Dante network
- Mic or Line is Selectable for Each XLR Input
- Switchable 48V Phantom Power for Each Mic XLR Input
- Adjustable Mic/LIne Gain from ‐20 dB to +20dB for Each XLR input (Two Audio Signal Outputs from Dante Network)
- Stereo/Mono switch for mini-jack input and output
- Four audio signal outputs from Dante network
- Balance or unbalanced signal outputs
- Doesn't require special software
- High Resolution 24 Bit for DAC and ADC
- Power over Ethernet (PoE) or 24VDC power supply
- Provides High Quality of Preamplifier for microphones
- Excellent Audio quality with low noise
|
|
Dante Interface 4 x Mic/Line Inputs, 4 x Outputs |
 |
C0375 |
|
- Impedance: 100Ω
- Sensitivity: -58dB ± 3dB
- Frequency response: 70Hz - 15kHz
- Cable Connection: Mini XLR
- Length: 330mm
- Polar pattern: Cardioid (unidirectional)
- Voltage: 11 - 52 Volts DC
|
|
An elegant, stylish, slimline unobtrusive desk-mount paging microphone equipped with a 3 pin balanced XLR lead. Features switchable flat or rolloff response to eliminate low frequency pickup. May also be switched to operate as push to talk or push to lock |
 |
C0357 |
|
- Uses the isolated voltage-boosting technology to effectively prevent the ground signal interference
- The built-in-low pass filter circuit design allows you to fully filter out the interference noise from the external audio equipment
- Soft start function to avoid the impulsive sound when boosting the device
- Uses two sets of balanced power supply, to balance the input and output signals which in turn makes the voltage balanced and stable
|
|
A compact single channel phantom power supply with 3 pin XLR female balanced input and 3 pin XLR male balanced 48V output.
Includes power supply.
Size: 88W x 47H x 92Dmm |
 |
A3194 |
|
- Allows digital signals to be transmitted using a single Cat5e or Cat6 cable
- Supports multichannel audio
- Select one input from Coaxial or Toslink input ports, and send S/PDIF audio signal to both Coaxial and Toslink output ports simultaneously
- 2 Emitter output connections
- Convenient IR confirmation LED
- Power receptacle with LED indicator
|
|
Allows digital signals to be transmitted using a single Cat5e or Cat6 cable. |
 |
X0705A |
|
- High Capacity Rechargeable Battery
- Low Battery Protection
- One-Button Recording
- Delete Function
- Highly Sensitive Stereo Microphone
- Password Protected
- Supports Multiple Formats
- Supports External Mic
|
|
This quality voice recorder features a sturdy diecast metal case for recording CD quality audio where ever you may need it. |
 |
A4373 |
|
- Maximum volume setting
- Minimum volume setting
- Australian designed and assembled
|
|
When fitted and used in conjunction with A 2280B wallplate to provide remote volume level adjustment. Ideal for situations where the amplifier is located in a remote rack. Plugs into the amplifier internally on the main board. |
 |
A1715 |
|
- Four MP3 audio messages available
- Micro SD Card storage of MP3 files (supplied)
- Stereo Dual RCA output
- Remote triggering of MP3 playback
- Manual playback of MP3 files
- 24V DC operation
- Supplied with 24V DC plugpack
|
|
The A 1715 is an MP3 based message player, housed in a convenient DIN rail housing. It has four independent contacts for remote triggering
of the four available MP3 audio files. |
 |
C0383 ROHS
|
|
- Polar Pattern: Unidirectional
- Housing Material: Zinc Diecast
- Impedance: 600 Ohm
- Sensitivity: -72dB ±3dB
- Frequency Response: 50Hz - 15kHz
|
|
This balanced microphone has a specially designed grill that can withstand a drop impact without losing its shape. The tough zinc diecast housing has an inbuilt 3 pin XLR male connector and on/off switch. It is supplied complete with 5m twin shielded bala |
 |
C0448 |
|
 Designed & manufactured in Australia.
- Since 1976 Redback public address products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
Dual 3pin XLR microphone connectors mounted horizontally on a dual face wall plate. "One-Shot" version with screw terminal connections for quick and easy connection on site. |
 |
CB0448 |
|
- Designed & manufactured in Australia.
- Since 1976 Redback public address products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
Dual 3pin XLR microphone connectors mounted horizontally on a dual face wall plate. "One-Shot" version with screw terminal connections for quick and easy connection on site. |
 |
A4825 |
|
- Two Balanced Microphone XLR Inputs
- Switch-Selectable Mic Gain and 48V Phantom Power on Side Panel
- Output Pair Selectors to go to Pair (A, B or C) for Each MIC Input
- Signal and Power Pairs Pass-Through on RJ45 jacks
- Daisy-Chain with a Single-Pair UTP Sender
- AFC Design (AFC: Auto Feedback Gain Circuitry)
|
|
This Dual 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). |
 |
C7281A |
|
- Dual channel 96 UHF frequencies in 520 - 544MHz UHF Band
- Range up to 100m
- Provides balanced mic or line level outputs
- 3 pin XLR or 6.35mm jack connection
- Hi/low impedance selector
- Compatible with Okayo beltpack and handheld transmitters sold separately
|
|
A dual channel receiver designed to integrate with the C 7282A Okayo transmitter system or Okayo UHF equipped portable PA systems. |
 |
A3043 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Microphone pre-amp gain: 40dB
- Min load: 4ohm
- Current draw: 2A max.
- Power: 12V dc
- Dimensions: 92.6L x 73.4W x 26.6H mm
- Weight: 160g
|
|
This compact amplifier is a great way to power a pair of speakers without the bulk of a full size hi-fi receiver. It provides 2x15W RMS output power - enough to power a pair of small ceiling or bookshelf speakers. |
 |
A6514 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
 Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
These compact modules are designed to remotely alter the volume of any low level signal source over serial control. |
 |
C0354 |
|
- Impedance: 500Ω balanced, dynamic
- Sensitivity: -80dB ±3dB
- Frequency response: 60Hz - 12KHz
- Length: ≈460mm
- Polar pattern: Cardioid (unidirectional)
- Switch: Momentary PTT
|
|
A high performance dynamic microphone with in-built PTT switch in the head for paging systems. Complete with flexible gooseneck and built in 3 pin male XLR connector, it is ideal for paging consoles and general announcing requirements in factories, warehouses, food outlets and venues. |
 |
C0373 |
|
- Insert: Dynamic
- Impedance: 500 Ohm balanced
- Sensitivity: -77dB ±3dB
- Frequency Response: 100Hz - 12kHz
- Length: 420mm
- Directivity: Unidirectional (Cardioid)
|
|
This microphone features outstanding speech intelligibility, feedback rejection and user sound insolation. Complete with flexible gooseneck and built in 3 pin male XLR connector, this is ideal for lecterns, custom paging consoles, church pulpits and some |
 |
C0363 |
|
- Impedance: 500Ω
- Sensitivity: -76dB ±3dB
- Frequency Response: 100Hz-10KHz
- Length: ≈325mm
- Directivity: Unidirectional
|
|
This elegant gooseneck microphone features smooth, brilliant sound with excellent ambient noise control and feedback rejection. It's screw base is suitable for mounting on equipment or permanent desk mounting . The slimline design of this mic makes it id |
 |
C0361 |
|
- Insert: BackElectret - Condenser
- Polar Pattern: Line + Gradient
- Impedance: 200 Ohm balanced
- Open Circuit Sensitivity: -60dB ±3dB
- Frequency response: 30Hz - 18kHz
- Maximum SPL: 119dB (1kHz @ 1% THD)
- Dynamic Range: 89dB (1kHz at 1Pa)
- Signal to Noise: 64dB (1kHz @ 1Pa)
- Operating Voltage: Phantom power 9V - 52V DC, 2mA typical
- Output Connector: Integral 3-pin XLR Male
- Dimensions: Ø19 x 288mm
- Included Accessories: Windscreen
|
|
This shotgun mic is designed to plug directly into a desk mount XLR socket. The line + gradient pattern provides an extremely tight unidirectional pickup and high rejection of back & side signals. It features a section of flexible gooseneck for angle adju |
 |
A4597 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
This remote wallplate interfaces with a building fire evacuation control board to offer simple fire alarm test triggering. |
 |
A2096 |
|
- Selectable line impedance 600Ω or 4.7kΩ
- Separate speaker for call tone
- Simple two wire connection
- Designed to comply with AS2220.1
- Includes wall mounting bracket
- 80db call tone
- 73mm overall height with the spacer and bracket removed
|
|
Designed specifically for use in emergency warning systems. Warden intercom points (WIPs) are used to communicate between floor wardens and the main emergency evacuation panel. When the handset is lifted the firephone automatically rings the emergency evacuation panel. When the emergency evacuation panel calls the WIP, the call tone sounds through |
 |
A4930 |
|
- Connects to A 4931 transmitter wallplate or other Redback UTP transmitter (see connection matrix)
- Connect up to four audio zones together.
- Easy Cat5e/6 UTP data cabling connection.
- Up to 300m cable runs out to zones.
- Balanced Euro terminal block connections.
- Balanced mic or line level operation.
- 24V DC operation.
- Australian designed & assembled.
|
|
This Microphone/Line Hub is designed to accept audio from up to four A 4931 Mic/Line Preamp wallplates. The Hub has a dedicated output for each wall plate, with front mounted volume controls for each output. |
 |
A2501 ROHS
|
|
|
|
Spare globe to suit the A 2499 and A 2500 gooseneck lights. 12VDC 5W |
