|
Description |
Downloads |
Specs |
Ordering |
|
 |
S9268 ROHS
|
|
- Connector Type: 1x BNC
- Cable Type: 75-ohm RG59, RG6, or RG11 video-grade coaxial cable
- Max. Transmission Distance: 600m (2000ft.) for the RG6 coaxial cable
- Ethernet Connector: 1x RJ-45 with LEDs on Connector
- Cable Type: Straight through or cross-over Cat5 Cable, Auto MDI/MDIX
- Rate: IEEE 802.3x, Auto-Detection for 10/100Base-T and full / half duplex
- Output Voltage: IEEE 802.3af/at PSE@ RJ45 Port
- LED Indicators: Coaxial Data Signal Strength, Green: GOOD (Link speed > 60Mbps) / Amber: MEDIUM (Link speed 20~60Mbps), Red: BAD (Link speed < 20Mbps) / Off: NO LINK
- Push Button: Reset / Pairing
- Input Operating Voltage: DC 56V / 0.03 - 1.6A
- Power Consumption: 1.5W (w/o power forwarding)
- Operation Temperature: -20°C ~ 60°C
- Humidity: 20% to 85% RH. (non-condensing)
- Storage Temperature: -30°C ~ 80°C
- Dimensions (W×D×H) mm: 38 x 120 x 33
- Weight: 176g
-
-
| Transmission Distance with Power Delivered: COAXIAL Cable |
-
-
-
Power Delivered
- & Power Source
|
-
Not using
- PoE output
|
-
| 5.5W |
-
| 7W |
-
| 9W |
-
| 12W |
-
| 17W |
-
-
-
| Maximum Coax RG6. Data Link Distance |
-
-
-
| DC56V Power Supplied |
-
| 2000m |
-
| 600m |
-
| 500m |
-
| 400m |
-
| 300m |
-
| 200m |
-
-
-
-
| Transmission Distance with Power Delivered: UTP Cable |
-
-
-
Power Delivered
- & Power Source
|
-
Not using
- PoE output
|
-
| 16W |
-
| 18W |
-
| 19.5W |
-
| 20W |
-
| 22W |
-
-
-
| Maximum Cat.5 (4-Pair) UTP Cable. Data Link Distance |
-
-
-
| DC56V Power Supplied |
-
| 600m |
-
| 600m |
-
| 500m |
-
| 400m |
-
| 300m |
-
| 200m |
-
|
|
A 10/100 ethernet over coax transceiver for sending ethernet only (no power) over
coaxial cabling. Two units are required to form a link. Alternatively, it can be used with S 9267 4 way splitter cable to four S 9268 transceivers. Requires 12V DC from either M 9273A or existing 12V supply using P 6715. Maximum coaxial length 2000m. |
 |
S9269 ROHS
|
|
|
|
These PoE transceiver units allow ethernet
and power to be sent along coaxial cabling.
The 48-56V power supply (M 8976A)
can be added for powering a 802.3at
PoE device (such as an IP camera) at the
receiving end. A master transceiver and
camera transceiver are required to make
a link. Alternatively, a transceiver unit
may be used with the S |
 |
S9270 |
|
|
|
These PoE transceiver units allow ethernet and power to be sent along coaxial cabling.
|
 |
S9271 |
|
|
|
Say goodbye to electricians and costly drilling and climbing through roof cavities to power your network devices with this network switch. The switch has Power over Ethernet (PoE) that is built-in to it. |
 |
S9274 |
|
- 1 LAN-In (Data + Power) +1 LAN-Out (Data Only)
- Take Power from PSE
- 5v 12v 24v 48v Passive POE
- 5v 12v 24v 48v Cheap price of cable type passive POE splitter
- Splitter: RJ45 Female to RJ45 Male + Power Out
- Passive PoE - means that input and output voltage are equal.
- Works with all DC powered non-PoE devices
- Supports 5V, 12V, 24V, 48V
- Power supply required for power input - simply use the power supply (wall transformer) that is provided with the device you are trying to power.
- Uses industry standard 5.5mm x 2.1mm power plugs
- Can work up to 150ft (depending on the quality of the cable and the power draw of the device)
|
|
These camera joiners come as a pair and have a transmission distance of under 70m. The input power of the joiners is 12V-48V. The joiners add to a professional appearance for IP camera power cabling. The joiners also make IP camera installation easier by saving time plus creating a more secure cable connection.
|
 |
S9722A |
|
- Gain: +5 dB
- Connector: SMA Male
- Operating frequency: 2.4Ghz
- Impedance: 50Ω
- Dimensions (mm): 12.5 x 195
- Weight: 30g
|
|
5dB omni antenna to suit 2.4GHz cameras and equipment.
Standard SMA connection. |
 |
S9738 |
|
- Built-in 9dBi 2x2 dual-polarized directional MIMO antenna
- Adjustable transmission power from 0 to 27dBm/500mw
- System-level optimizations for >5km long range wireless transmission (up to 15km depending on installation conditions)
- TP-LINK Pharos MAXtream TDMA (Time-Division-Multiple-Access) technology improves product performance in throughput, capacity and latency performance, ideal for PTMP applications
- Centralized Management System – Pharos Control
- AP / Client / Repeater / AP Router / AP Client Router (WISP) operation modes
- Passive PoE Adapter supports up to 60 meter (200 feet) Power over Ethernet deployment and allows the device to be reset remotely
|
|
TP-LINK's 2.4GHz 300Mbps 9dBi Outdoor CPE, the CPE210 is dedicated to cost effective solutions for outdoor wireless networking applications. With its centralized management application, it is flexible and ideal for point-to-point, point-to-multipoint and outdoor Wi-Fi coverage applications. |
 |
S9740 |
|
- Built-in 13dBi 2x2 dual-polarized directional MIMO antenna
- Adjustable transmission power from 0 to 27dBm/500mw
- System-level optimizations for more than 15km long range wireless transmission
- TP-LINK Pharos MAXtream TDMA (Time-Division-Multiple-Access) technology improves product performance in throughput, capacity and latency performance, ideal for PTMP applications
- Centralized Management System – Pharos Control
- AP / Client / Repeater / AP Router / AP Client Router (WISP) operation modes
- Passive PoE Adapter supports up to 60 meter (200 feet) Power over Ethernet deployment and allows the device to be reset remotely
|
|
TP-LINK's 2.4GHz 300Mbps 9dBi Outdoor CPE, the CPE210 is dedicated to cost effective solutions for outdoor wireless networking applications. With its centralized management application, it is flexible and ideal for point-to-point, point-to-multipoint and outdoor Wi-Fi coverage applications. |
 |
S9745 |
|
- EAP Controller Software enables administrators to easily manage hundreds of EAPs
- Support Passive PoE for convenient and affordable installation
- Simple mounting design to easily mount to a wall or ceiling
- 300Mbps wireless data rate for uninterrupted wireless connection
- Captive portal provides one convenient method of authentication for Wi-Fi guests
- Rate limit on per SSID to restrict the bandwidth of each client
- Access Control restricts or allows the client to access the specified network segment
- Reboot Schedule enables all the APs to be rebooted automatically within a specified time
- WPA/WPA2-enterprise, 802.1X with RADIUS secure authentication and rogue access point detection ensure the security of WLAN
- Multi-SSID divides multiple wireless network for different users
- Load balance ensures large numbers of users have smooth network experiences in large business networks
- Compatible with 802.11 b/g/n products
- Multiple operating modes satisfy different application conditions including managed AP and standalone AP modes
- QoS function prioritizes data, voice, and video applications to ensure time-sensitive traffic takes priority over all other traffic
- Prevents dust from dropping onto the PCB through bypass louver, which ensures long-term, unhindered operation.
|
|
As a long range indoor wireless device, the EAP110 is designed to provide a multiple connection and long distance wireless networking solution. It operates seamlessly in the 2.4GHz frequency spectrum and provides wireless data transfer rates of up to 300Mb |
 |
S9747 |
|
- Fast Dual-Band Wi-Fi: Simultaneous 450 Mbps on 2.4 GHz and 867 Mbps on 5 GHz totals 1317 Mbps Wi-Fi speeds.
- Integrated into Omada SDN: Zero-Touch Provisioning (ZTP), Centralised Cloud Management, and Intelligent Monitoring.
- Centralised Management: Cloud access and Omada app for ultra convenience and easy management.
- Seamless Roaming: Even video streams and voice calls are unaffected as users move between locations.
- PoE Support: Support both standard 802.3af/at and Passive PoE (PoE adapter included) for flexible installations.
- Secure Guest Network: Along with multiple authentication options (SMS/Facebook Wi-Fi/ Voucher, etc.) and abundant wireless security technologies.
- Advanced Wireless Tech: Optimize network performance with MU-MIMO, Band Steering, Airtime Fairness and Beamforming technologies.
|
|
As a long range indoor wireless device, the EAP225 is designed to provide a multiple connection and long distance wireless networking solution. It operates seamlessly in the 2.4GHz and 5GHz frequency spectra and provides wireless data transfer rates of up to 1200Mb |
 |
S9749A NEW
|
|
- Ultra-Fast Wi-Fi 6 Speeds
- 4× increased capacity to connect more devices simultaneously
- Integrated into Omada SDN
- Cloud access and Omada app for ultra convenience and easy management.
- Seamless Roaming
- PoE+ Support
- Along with multiple authentication options (SMS/Facebook Wi-Fi/ Voucher, etc.) and abundant wireless security technologies.
|
|
This high performance ceiling mount wireless access point for general corporate Wi-Fi features the latest 802.11ax technologies like 1024 QAM and Long OFDM Symbol, which allows the EAP to boost overall speeds up to 1775 Mbps (1201 Mbps on a 5 GHz band and 574 Mbps on a 2.4 GHz band) |
