|
Description |
Downloads |
Specs |
Ordering |
|
|
A4935 |
|
- Standard dual gang wallplate
- Connects via RJ45 UTP cabling
- Mixed audio output
- Connects to A 4942 balanced UTP receiver or other Redback UTP compatible products.
- Individual & master level controls
- Stereo RCA input
- 24V DC input via Cat5 UTP cable from connected equipment
- 3 pin XLR mic/line level inputs
|
|
These local zone input wallplates allow for multiple mic/line inputs to be sent over UTP cabling back to a single receiver for connection to a zone amplifier. |
|
A3194 |
|
- Allows digital signals to be transmitted using a single Cat5e or Cat6 cable
- Supports multichannel audio
- Select one input from Coaxial or Toslink input ports, and send S/PDIF audio signal to both Coaxial and Toslink output ports simultaneously
- 2 Emitter output connections
- Convenient IR confirmation LED
- Power receptacle with LED indicator
|
|
Allows digital signals to be transmitted using a single Cat5e or Cat6 cable. |
|
A4824 |
|
- Balanced MIC XLR Input
- Selector switch MIC GAIN
- RCA Jack Audio Inputs
- XLR Goes to Pair A; L (Left) Goes to Pair B; R (Right) Goes to Pair C.
- Signal and Power Pair Pass-Through on RJ45 jack
- Power can be linked to the removable terminal
- Blue LED Indicates Module is Powered
- Daisy chain topology
- AFC Design (AFC: Auto Feedback Gain Circuitry)
|
|
This 3 pin XLR Line/Balanced and Stereo RCA input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). |
|
A4820 |
|
- Balanced MIC XLR Input
- Selector switch MIC GAIN
- Switch Selects which Pair (A, B or C) Feeds the Output
- Signal and Power Pair Pass-through on RJ45 jacks
- Power can be linked to the removable terminal
- Daisy chain topology
- AFC Design (AFC: Auto Feedback Gain Circuitry)
|
|
This 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). |
|
A4821 |
|
- Mini / RCA(MONO) Jacks Audio Inputs
- Switch Selects which Pair (A, B or C) Feeds the Output
- Signal and Power Pair Pass-through on RJ45 jacks
- Power can be linked to the removable terminal
- Blue LED Indicates Module is Powered
- Daisy chain topology
- AFC Design (AFC: Auto Feedback Gain Circuitry)
|
|
This Stereo RCA and 3.5mm Jack Wallaplate can be used in a stand-alone point to point basis, allowing signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). |
|
A4818 |
|
- Two Mic/Line XLR Inputs and one mini-jack input on Front Panel
- Terminal Block for Two Audio Outputs on Rear Panel
- One mini-jack output on front panel
- Converts Mic or Line Audio Signals to Dante network
- Mic or Line is Selectable for Each XLR Input
- Switchable 48V Phantom Power for Each Mic XLR Input
- Adjustable Mic/LIne Gain from ‐20 dB to +20dB for Each XLR input (Two Audio Signal Outputs from Dante Network)
- Stereo/Mono switch for mini-jack input and output
- Four audio signal outputs from Dante network
- Balance or unbalanced signal outputs
- Doesn't require special software
- High Resolution 24 Bit for DAC and ADC
- Power over Ethernet (PoE) or 24VDC power supply
- Provides High Quality of Preamplifier for microphones
- Excellent Audio quality with low noise
|
|
Dante Interface 4 x Mic/Line Inputs, 4 x Outputs |
|
A4825 |
|
- Two Balanced Microphone XLR Inputs
- Switch-Selectable Mic Gain and 48V Phantom Power on Side Panel
- Output Pair Selectors to go to Pair (A, B or C) for Each MIC Input
- Signal and Power Pairs Pass-Through on RJ45 jacks
- Daisy-Chain with a Single-Pair UTP Sender
- AFC Design (AFC: Auto Feedback Gain Circuitry)
|
|
This Dual 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). |
|
A4831 |
|
|
|
Interfaces 2 input and 4 output CSP UTP wallplates with Dante® systems |
|
A4834 |
|
- Transmits three balanced audio signals or 3 unbalanced line level signals
- CSP transfer protocol with Dante compatible converters available (see A 4830/31)
- Local power input (powered at one end of cable run)
|
|
This audio distribution system uses affordable UTP cabling to send up to three balanced inputs (terminal block) or mono RCA signals over long distances. |
|
A4937 NEW
|
|
- Standard dual gang wallplate
- Connects via RJ45 UTP cabling
- Mixed audio output
- Bluetooth audio streaming receiver in-built
- Connects to A 4942 balanced UTP receiver or other Redback UTP compatible products.
- Individual & master level controls
- Stereo RCA input
- 24V DC input via Cat5 UTP cable from connected equipment
- 3 pin XLR mic/line level inputs
|
|
These local zone input wallplates allow for multiple mic/line inputs to be sent over UTP cabling back to a single UTP receiver for connection to a zone amplifier. This model also features bluetooth audio streaming for local zone playback of music. |
|
A4832 |
|
- Design Transceiver and Receiver in one Module
- Provides the Power to Connected Receivers
- Sends Left and Right Audio Channels
- Unbalanced Stereo RCA Input from Audio Source
- Balanced 3.5 Jack Audio Input from Mono Source
- Audio Signal Goes to two UTP RJ45 Outputs
- CSP Receiver Compatible with all 2 pair transceiver wallplates
- Two RCA stereo unbalanced outputs
- L (Left) Output Goes to Pair B; R (Right) Goes to Pair C
- Daisy chain topology
- AFC Design (AFC: Auto Feedback Gain Circuitry)
|
|
A compact system hub for interfacing input and output wallplates together with existing zone audio amplifiers and audio sources. |
|
A5332 |
|
- Input impedance: 20KΩ (bal.)
- Maximum input level: ≥16dB
- Connections: Balanced XLR, 6.35mm jack
- Output impedance: 100Ω
- Maximum output level: ≥15dB
- Equaliser control 31 band (1/3 octave)
- High pass filter: 40Hz 12dB/octave
- Feedback threshold LED: ≥-22dB
- Peak sensitivity: Lit 3dB before clip point
- Frequency response: 20Hz - 20KHz (±0.5dB)
- THD + S/N %: <0.1% (20Hz - 20KHz @ 0dB)
- S/N ratio: ≥90dB
- Power supply: 240VAC
- Dimensions: ≈482W x 230D x 132Hmm
- Weight: 5.4kg
|
|
This professional unit delivers outstanding equalisation both in live or studio applications. Invaluable
for counteracting poor room or venue acoustics. The design employs ultra low noise audio amplifiers
with high quality components for outstanding sou |
|
A4826 |
|
- XLR / RCA Audio Output,
- Gain Switch XLR only
- Signals from Pair A(XLR), Pair B(L) and Pair C(R).
- Power can be linked to the removable terminal
- Blue LED Indicates Module is Powered
|
|
This 3 pin XLR Balanced and Stereo RCA output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates).
|
|
A4835 |
|
- CSP transfer protocol with Dante compatible converters available (see A 4830/31)
- Local power input (powered at one end of cable run)
- Maximum distance over Cat6 cable: 1200 metres.
|
|
This audio distribution system uses affordable UTP cabling to send up to three balanced inputs (terminal block) or mono RCA signals over long distances. |
|
A4942 |
|
- Connects via RJ45 UTP cabling
- Point to point connection
- 3 pin models allow mic or line level connection
- DIP switch selectable sensitivity
- Level control
- 24V DC input
|
|
The Redback® A 4942 receives audio from compatible Redback® Cat5e/6 transmitters and converts the signal to a balanced XLR output. The output level is DIP switch selectable, and the ouput volume is screwdriver adjusted via the trimpot on the front of the unit. |
|
A4827 |
|
- Balanced MIC XLR Output
- Selector switch MIC GAIN
- Switch Selects which Pair (A, B or C) Feeds the Output
- Signal and Power Pair Pass-through on RJ45 Jacks
- Power can be linked to the removable terminal
- Blue LED Indicates Module is Powered
- Daisy chain topology
- AFC Design (AFC: Auto Feedback Gain Circuitry)
|
|
This 3 pin XLR Balanced Output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). |
|
A2516 NEW
|
|
- Frequency response: 20 Hz - 20kHz +/- 3dB
- Input level: 0.775Vrms
- Output level: 0.19Vrms (measured at 1kHz with volume control set to max).
- Maximum output level before distortion: +18dBm
- Note the RCA input sockets are in parallel
|
|
Unbalanced 10K Ohm 2 x RCA to balanced 600 Ohm 3 pin male XLR (or optional screw terminal connections) with level control. |
|
A4940 |
|
- Connects via RJ45 UTP cabling
- Point to point connection
- 3 pin models allow mic or line level connection
- DIP switch selectable sensitivity
- Level control
- 24V DC input
|
|
Allows balanced signals to be transmitted over long distances using economical UTP data cabling. |
|
A4816 |
|
- Four Mic/Line XLR Inputs on Front Panel
- Terminal Block for Two Audio Outputs on Rear Panel
- Converts Mic or Line Audio Signals to Dante network
- Mic or Line is Selectable for Each XLR Input
- Switchable 48V Phantom Power for Each Mic XLR Input
- Adjustable Mic/LIne Gain from ‐20 dB to +20dB for Each XLR input (Two Audio Signal Outputs from Dante Network)
- Balanced or Unbalanced Signal Outputs
- High Resolution 24 Bit for DAC and ADC
- Power over Ethernet (PoE) or 24VDC power supply
- Provides High Quality of Preamplifier for microphones
- Excellent Audio quality with low noise
|
|
Dante Interface 4 x Mic/Line Inputs, 2 x Line Outputs |
|
A4822 |
|
- RCA Jack Audio Inputs
- L (Left) Output Goes to Pair B; R (Right) Output Goes to Pair C
- Signal and Power Pair Pass-Through on RJ45 jacks
- Power can be linked to the removable terminal
- Blue LED Indicates Module is Powered
- Daisy chain topology
- AFC Design (AFC: Auto Feedback Gain Circuitry)
|
|
This Stereo RCA input wallplate can be used in a stand-alone point to point basis, allowing signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). |
|
A0642B |
|
|
|
By law any radio, amplifier etc connected to a telephone system (for background music or paging applications) must be isolated with a line isolation unit (LIU). Adjustable output level suits all telephone systems. |
|
A4828 |
|
- Stereo RCA Jack Audio Outputs
- Signals from Pair B(L) and Pair C(R).
- Source Loop
- Power can be linked to the removable terminal
- Blue LED Indicates Module is Powered
- Daisy chain topology
|
|
This Stereo RCA Jack output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). |
|
A4950 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
By adding this module inline with a paging microphone pre and post announcement chimes can be added to the audio signal. |
|
A2515 NEW
|
|
- Frequency response: 20 Hz - 20kHz +/- 3dB
- Input level: 0.775Vrms
- Output level: 1.97Vrms (measured at 1kHz with volume control set to max).
- Maximum output level before distortion: +24dBm
- Note the RCA output sockets are in parallel
|
|
Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control (or optional screw terminal connections). |
|
A4948 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
This compact module is designed to go inline with an audio input source like CD/Blu-Ray etc to the input of a mixer or amplifier. It maintains a constant level to the mixer/amp regardless of the amplitude of the input signal. |