|
Description |
Downloads |
Specs |
Ordering |
|
 |
C0361 |
|
- Insert: BackElectret - Condenser
- Polar Pattern: Line + Gradient
- Impedance: 200 Ohm balanced
- Open Circuit Sensitivity: -60dB ±3dB
- Frequency response: 30Hz - 18kHz
- Maximum SPL: 119dB (1kHz @ 1% THD)
- Dynamic Range: 89dB (1kHz at 1Pa)
- Signal to Noise: 64dB (1kHz @ 1Pa)
- Operating Voltage: Phantom power 9V - 52V DC, 2mA typical
- Output Connector: Integral 3-pin XLR Male
- Dimensions: Ø19 x 288mm
- Included Accessories: Windscreen
|
|
This shotgun mic is designed to plug directly into a desk mount XLR socket. The line + gradient pattern provides an extremely tight unidirectional pickup and high rejection of back & side signals. It features a section of flexible gooseneck for angle adju |
 |
C8893D |
|
- Compact & lightweight
- Fitted with 3 pin mini XLR socket
- On / Off / Mute switch
- Gain control
- Requires 2 x AA batteries (either alkaline or rechargeable).
|
|
Beltpack transmitter ideal for use with the Redback 700 channel receiver unit (C 8890D). |
 |
A4940 |
|
- Connects via RJ45 UTP cabling
- Point to point connection
- 3 pin models allow mic or line level connection
- DIP switch selectable sensitivity
- Level control
- 24V DC input
|
|
Allows balanced signals to be transmitted over long distances using economical UTP data cabling. |
 |
A4942 |
|
- Connects via RJ45 UTP cabling
- Point to point connection
- 3 pin models allow mic or line level connection
- DIP switch selectable sensitivity
- Level control
- 24V DC input
|
|
The Redback® A 4942 receives audio from compatible Redback® Cat5e/6 transmitters and converts the signal to a balanced XLR output. The output level is DIP switch selectable, and the ouput volume is screwdriver adjusted via the trimpot on the front of the unit. |
 |
A4944 |
|
|
|
The Redback® A 4944 provides a convenient way to send line level RCA audio signals over long distances via Cat5/6 cabling. The unit has DIP switch selectable input sensitivities of 100mV and 1V to handle inputs of varying levels.
|
 |
A4946 |
|
|
|
The Redback A 4946 receives audio from compatible Redback Cat5e/6 transmitters, converts the signal to line level and outputs to RCA and 3.5mm connectors. |
 |
A4950 |
|
-
 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
 Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
By adding this module inline with a paging microphone pre and post announcement chimes can be added to the audio signal. |
 |
A4948 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
This compact module is designed to go inline with an audio input source like CD/Blu-Ray etc to the input of a mixer or amplifier. It maintains a constant level to the mixer/amp regardless of the amplitude of the input signal. |
 |
A4941 |
|
- Connects via RJ45 UTP cabling
- Point to point connection
- Allows mic or line level connection
- DIP switch selectable sensitivity
- Level control
- Fits into a single gang wallbox
- 24V DC input
|
|
This handy interface wallplate allows balanced signals to be transmitted over long distances using economical UTP data cabling. |
 |
A4953 |
|
- Connects via RJ45 UTP cabling
- Point to point connection
- DIP switch selectable sensitivity
- Level control
- Fits into a single gang wallbox
- 24V DC input
|
|
This handy interface wallplate allows balanced signals to be transmitted over long distances using economical UTP data cabling. |
 |
A4952 |
|
|
|
This handy interface box allows balanced signals to be transmitted over long distances using economical UTP data cabling, and provides easy local zone connection for audio sources. |
 |
A4954 |
|
|
|
The Redback® A 4954 receives audio from compatible Redback® Cat5e/6 transmitters and converts the signal to a balanced XLR output with PTT connection. |
 |
A4905 |
|
- XLR Mic input
- RCA Aux input
- XLR balanced output.
- Phantom power to Mic Input (15V DC).
- Controls for AUX, MIC and master volume.
- DIP Switch selectable AUX input sensitivity.
- 24VDC operation via 2.1mm DC power jack.
|
|
This line pre-amp will accept either a microphone or auxiliary input and convert it to a balanced high level signal suitable for distribution up to 500M without interference with up to 3V of output level available. Volume controls are provided for both inputs plus a master volume control. The microphone is a balanced XLR input whilst the auxiliary |
 |
C0327 |
|
- All metal casing and grille.
- PTT pair for muting auxiliary inputs.
- Heavy duty bare end cord.
- 450mm gooseneck with screw fit base.
- Ideal for supermarkets, fast food restaurants etc.
|
|
This incredibly sturdy all metal microphone is built to survive the rigours of supermarkets & fast food restaurants. |
 |
A4489A |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 45 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
The A4489A zone relay unit may be installed remotely and has been designed to switch either low level inputs or amplifier outputs and interfaces the A4660 paging console with existing PA systems. Suits for line level or 100V line zone switching. |
 |
A4469 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 45 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
The A4469 zone relay unit may be installed remotely and has been designed to switch either low level inputs or amplifier outputs and interfaces the A4660 paging console with existing PA systems. |
 |
A6507 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 45 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
This compact module includes a seven step 100V line speaker attenuator/volume control which can be remotely adjusted via RS 485 serial control. |
 |
C0356 |
|
- Impedance: 250Ω
- Sensitivity: -65dB ±2dB
- Frequency Response: 30Hz-20KHz
- Pattern: Cardioid
- Cable Length: 6m
|
|
This cardioid microphone is designed to be mounted from ceilings in installations such as churches where greater noise isolation is required. Low profile design and flexible cable hanger provide for diverse mounting options and minimum visibility. Phant |
 |
C0351A |
|
- Insert: Electret
- Impedance: 250Ω balanced
- Sensitivity: -52dB ±3dB
- Frequency response: 30Hz - 18kHz
- Polar pattern: Cardioid/Fig 8/Omni/Variable
- Dimensions: 100L x 93W x 26Hmm
|
|
This boundary microphone is designed to be surface mounted and is fitted with a high sensitivity electret insert. The sturdy diecast case and steel grille offers robust protection, while the rubber base plate minimises vibration pickup. A front panel on/o |
 |
A4568 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
Designed to interface the A4567 Line monitoring unit with a fire indicator board. The addition of the A4568 enables you to monitor the status of each individual zone. |
 |
A4931 |
|
- Input Mic Level Sensitivity: 3mV
- Input Line Level Sensitivity: 1V
- Music Input Level Sensitivity: 500mV
- Output Connector: RJ45 8P8C
- Input Connectors: Audio: 3 pin XLR balanced 2 x RCA, 3.5mm JACK
|
|
This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. |
 |
A5138 |
|
- Input Mic Level Sensitivity: 3mV
- Output Connector: RJ45 8P8C
- Input Connector: 5 pin XLR balanced
|
|
The A5138 UTP wall plate has a standard 5 Pin XLR connector for connection of microphones with PTT switches. |
 |
A4931V |
|
- Input Mic Level Sensitivity: 3mV
- Input Line Level Sensitivity: 1V
- Music Input Level Sensitivity: 500mV
- Output Connector: RJ45 8P8C
- Input Connectors: Audio: 3 pin XLR balanced 2 x RCA, 3.5mm JACK
|
|
This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. |
 |
C8893B |
|
- Compact & lightweight
- Fitted with 3 pin mini XLR socket
- On / Off / Mute switch
- Gain control
- Switchable impedance between mic & instrument pickup
- Requires 2 x AA batteries (either alkaline or rechargeable).
- Note: Beltpacks are not supplied with a mic. Lapel mic to suit is C 8907.
|
|
Beltpack transmitter ideal for use with the Redback 700 channel receiver unit (C 8890B). |
 |
A4932 |
|
- Input Mic Level Sensitivity: 3mV
- Input Line Level Sensitivity: 1V
- Music Input Line Level Sensitivity: 200mV
- Output Connector: RJ45 8P8C
- Input Connectors (Audio): 3 pin XLR balanced, 2 x RCA, 3.5mm JACK
- Dimensions: ~133W x 65D x 44H
- Weight: ~0.2 kg
|
|
This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. |
