|
Description |
Downloads |
Specs |
Ordering |
|
 |
Z6428 |
|
- Low-noise analog signal path.
- 5µs output rise time in response to step input current.
- 50 kHz bandwidth.
- Total output error 1.5% at TA= 25°C, and 4% at –40°C to 85°C.
- Small footprint, low-profile SOIC8 package.
- 1.2 mΩ internal conductor resistance.
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
- 5.0 V, single supply operation.
- 66 to 185 mV/A output sensitivity.
- Output voltage proportional to AC or DC currents.
- Extremely stable output offset voltage.
- Nearly zero magnetic hysteresis.
|
|
A fully Integrated, Hall Effect-Based Linear AC/DC Current Sensor with a 5A rating. Typical applications include motor control, load detection and management, switch-mode power supplies, and over current protection Arduino projects. |
 |
K8399A |
|
- Colour: White
- Reel Weight: 1kg
- ±0.02mm tolerance
- 1.75mm filament offering excellent print quality and accuracy
- Supplied in vacuum sealed plastic bag
- 100% bubble free filament
- Offers tensile strength and fluidity
- Non Toxic filament
- Compatible with most 3D printers and 3D printing pens
|
|
1.75mm filament offering excellent print quality and accuracy. All reels 1kg. 0.02mm tolerance. Supplied in vacuum sealed plastic bag. Compatible with most 3D printers and 3D printing pens. |
 |
K2930 |
|
|
|
If you need to switch mains voltages, say from a micro's out- put or any other low voltage source, you need to isolate them from each other. That&rsquos what this project does - it's easy to build and keeps mains voltages locked away from the controller and you! Virtually any low voltage source will do - from 2.7 to 10V. |
 |
K5315 |
|
- Channels: two
- Equaliser bands: seven (63Hz, 160Hz, 410Hz, 1kHz, 2.5kHz, 6.2kHz, 16kHz)
- Boost/cut: approximately ±12.5dB (bands overlap; see Fig.1) Signal-to-noise ratio: 108dB (2V RMS), 102dB (1V RMS)
- Total harmonic distortion: <0.0005%, 20Hz-20kHz, 20Hz- 22kHz bandwidth (see Fig.2)
- Input impedance: 100kΩ
- 100pF Output impedance: 470Ω
- The power supply as supplied supports 18-24V for the DC option, not 12-24V
- Channel separation: >50dB, 20Hz-20kHz (>=80dB 20Hz-1kHz)
- Other features: compact design, uses rotary pots for easy panel mounting
|
|
This stereo version of Silicon Chip’s new equaliser is perfect for new and existing home Hi-Fi systems. It features extremely low noise and distortion, so it won’t degrade your signal. Multiple methods of powering the unit make fitting it into an existing system a breeze. |
 |
K9300 |
|
- Contactless operation
- 90-100mm detection range
- No batteries (in tags) to go flat
- Stores up to 24 tag ID codes
- Easy tag addition & removal
- Works through any non-metallic material
- Audio feedback via on-board beeper
- Tamper detection
- Arm & alarm outputs
- Electric door strike output
- Suitable for home or car use
- Requires 12V DC @ 40mA (nominal)
|
|
Essentially, the system consists of a reader module and one or more "tags". Based on RFID (Radio Frequency Identity) technology, each tag is encoded with a unique identity. When a tag is brought within range of th |
 |
K6049 |
|
- Altronics kits are premium do-it-yourself projects designed to be assembled with ease. However, basic electronics knowledge and soldering skills are essential to construct our kits. A difficulty rating is provided to help determine if your ability is sufficient to build the kit project. Please note, once assembly has been commenced we are unable to honor any warranty claims. Please see the full details here.
|
|
The Brownout Protector is designed to protect single-phase induction motors in fridges, freezers, pumps etc from burnout if they attempt to start during a brownout. It will switch off the power if the voltage falls below a set threshold.
|
 |
H8952A |
|
- Sleek minimal design
- 2 x Standard 'type A' HDMI ports
- Aluminium Alloy top for passive cooling
- Programmable 30mm fan
- Clean Power Shutdown
- Multi-function power button
- Power management modes (with Always ON)
- Magnetic top access to GPIO pins
- Colour coded GPIO pins
- Easy installation
|
|
This Raspberry Pi 4 Argon ONE V2 Case not only has brilliant passive cooling (the whole top part of the case is a heatsink) but also protects the Raspberry Pi without compromising the full functionality of the motherboard. |
 |
Z6429 |
|
- Low-noise analog signal path.
- 5µs output rise time in response to step input current.
- 50 kHz bandwidth.
- Total output error 1.5% at TA= 25°C, and 4% at –40°C to 85°C.
- Small footprint, low-profile SOIC8 package.
- 1.2 mΩ internal conductor resistance.
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
- 5.0 V, single supply operation.
- 66 to 185 mV/A output sensitivity.
- Output voltage proportional to AC or DC currents.
- Factory-trimmed for accuracy.
- Extremely stable output offset voltage.
- Nearly zero magnetic hysteresis.
|
|
A fully Integrated, Hall Effect-Based Linear AC/DC Current Sensor with a 30A rating. Typical applications include motor control, load detection and management, switch-mode power supplies, and over current protection Arduino projects. |
 |
K8610 NEW
|
|
|
|
This high performance 3D printer with a more aesthetic, streamlined design, features a brand new nozzle made of brass that can stand up to +300°C printing temperature and is compatible with PLA, ABS, PVA, TPU, PA, PETG and wood. |
 |
K5532 |
|
- 9-36VDC power supply, with polarity protection.
- Fixed inverting gains of 1, 10 & 100 for single ended signals.
- Fixed gain of 100 for differential signal.
- Precision adjustable gain of 10±2%.
- 2 51Ω impedance outputs.
|
|
If you’ve ever tried to view a microphone signal on an oscilloscope and lost it in the noise, then you’ll know just how handy a signal amplifier can be. This kit provides a breakout for the high-performance AD4625-1 opamp with provision for a number of fixed gains, suitable for working with audio signals. |
 |
Z6583 |
|
- Small size, millimetre precision
- Can be protected behind many cover-window materials.
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
The PiicoDev® Distance Sensor is a long-distance laser-ranging sensor that uses Time-of-Flight (ToF) to accurately measure distances up to 4m. |
 |
Z6391A |
|
- 3 magnetic field channels and 3 acceleration channels
- From ±1.3 to ±8.1 gauss magnetic field full scale
- ±2g/±4g/±8g/±16g linear acceleration full scale
- 16-bit data output
- I2C serial interface
- Analog supply voltage 2.16 V to 3.6 V
- Power-down mode / low-power mode
- 2 independent programmable interrupt generators for free-fall and motion detection
- Embedded temperature sensor
- Embedded FIFO
- 6D/4D-orientation detection
|
|
Add the power of orientation to your next project with this triple-axis accelerometer/magnetometer compass module. |
 |
K2112 |
|
|
|
(SC July '94) Designed to compliment the K 2115 Champ Amplifier When it comes to simplistic but effective circuitry design, you can't beat the pre-champ. It has been designed to compliment the CH-AMP kit which when |
 |
K5310 |
|
- Channels: one
- Equaliser bands: seven (63Hz, 160Hz, 410Hz, 1kHz, 2.5kHz, 6.2kHz, 16kHz)
- Boost/cut: approximately ±12.5dB (bands overlap; see Fig.1) Signal-to-noise ratio: 108dB (2V RMS), 102dB (1V RMS)
- Total harmonic distortion: <0.0005%, 20Hz-20kHz, 20Hz- 22kHz bandwidth (see Fig.2)
- Input impedance: 100kΩ
- 100pF Output impedance: 470Ω
- The power supply as supplied supports 18-24V for the DC option, not 12-24V.
- Other features: compact design, uses rotary pots for easy panel mounting
|
|
This mono version of Silicon Chip’s new equaliser is perfect for instrument boxes or PA systems. It features extremely low noise and distortion, so it won’t degrade your signal. Multiple methods of powering the unit make fitting it into an existing system a breeze. |
 |
P1016 |
|
|
|
Multi-colour reusable leads for prototyping and working with development shields. Pin to pin (male to male) type. 65 pieces. |
 |
Z6421A |
|
- Ultra compact form factor
- Dual core ARM Cortex M0+ processor
- Two SPI controllers
- Two I2C controllers
- 16 PWM channels
- 26 multifunction GPIO pins
- Three analogue inputs
- On board USB controller
- In-built temperature sensor
- Castellated module allows soldering direct to carrier boards
- Drag-and-drop programming using mass storage over USB
- Low-power sleep and dormant modes
- Accurate on-chip clock
- Accelerated integer and floating-point libraries on-chip
- Includes headers
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2040, a brand new microcontroller chip designed by Raspberry Pi in the UK. From controlling appliances to operating a light display, Raspberry Pi Pico puts the technology that underpins countless everyday operations into your hands. |
 |
H8965 |
|
- High-quality, two-part ABS construction
- Cut-outs for the dual micro HDMI, Audio/Video, USB and Ethernet ports, as well as the USB-C power connector and access to the microSD card.
|
|
A compact, snap together black and grey case to suit the Raspberry Pi 4 Model B development board. Designed with all connection recesses and venting. |
 |
K5842 |
|
- RCA input and output connectors
- Audio and Video scanning
- Pause button
- Adjustable scan rate
- LED position indicators
|
|
(SC June '01) If your home or business has more than one CCTV security camera you will want an automatic scanner that switches between the cameras so you can see what's happening, all on a single monitor. |
 |
K2620 |
|
- Shows two voltages, two currents and one temperature reading on a 16x2 LCD
- In alternative USB mode, ASCII text from virtual serial port is written directly to 20x4 LCD
- Panel meter input range: 5 x 0-4.096V
- Panel meter scaling: 2 x 0-4.096V -> 0-60V, 2 x 0-4.096V -> 0-9A, 1 x 0-3V -> 0-100°C
- Panel meter resolution: 58.6mV for voltages, 8.79mA for currents
- Panel meter update rate: 5Hz
|
|
This simple and cheap device has many uses, but it’s mainly intended to replace multiple panel meters. It can also be used as a small additional text screen for PC, Raspberry Pi or any other computer with USB. |
 |
K8612 NEW
|
|
- 300°C high temp nozzle.
- 300 x 300 x 400mm build volume.
- HD monitor camera in-built.
- Wi-Fi, Bluetooth and Ethernet connectivity.
- Trapezoidal design for added stability on large volume prints.
- Wide compatability with a variety of filament including PLA, ABS, PVA, TPU, PA, PETG and wood.
- Full-metal dual gear direct extruder.
- CR Touch 16 point automatic levelling sensor or manual levelling as desired.
- LED light bar.
- Spring steel flexible magnetic build plate.
- Silent main board - no noisy stepper motors!
- Filament sensor.
- Pause/resume printing.
- Creality Cloud Printing with iOS/Android app support.
- Supplied mostly assembled to get you printing faster (assembles in under 30 mins).
|
|
The 7 module design of this high performance 3D printer enables assembly within 10 minutes. |
 |
K9800 |
|
- Altronics kits are premium do-it-yourself projects designed to be assembled with ease. However, basic electronics knowledge and soldering skills are essential to construct our kits. A difficulty rating is provided to help determine if your ability is sufficient to build the kit project. Please note, once assembly has been commenced we are unable to honor any warranty claims. Please see the full details here.
|
|
This 3 state logic probe design includes power connection leads and utilises the LM339N chip to provide logic states when checking circuits, output pins on boards etc. |
 |
Z6516A NEW
|
|
- 7’’ standard display, 1024x600 resolution
- Capacitive touch screen, maximum support 5 point touch
- Supports backlight control, the backlight can be turned off to save power
- Supports standard HDMI interface input.
- Can be used as general-purpose-use HDMI monitor, for example: connect with a computer HDMI as the sub-display (resolution of the output has to be able to adjust to 800X480)
- Used as a Raspberry Pi display that supports Raspbian, Ubuntu, Kodi, win10 IOT, single-touch, free drive etc.
- Works as a PC monitor, support win7, win8, win10 system 5 point touch (XP and older version system: single-point touch), free drive.
|
|
A 1024x600 touchscreen for Raspberry Pi that supports standard HDMI interface input which can be directly connected to Raspberry Pi. |
 |
Z6345 |
|
|
|
A 16x2 black character screen with green backlight. Push buttons are provided for up, down, left, right and select. Ideal for scrolling and selecting menu options. Works with the LiquidCrystal library in Arduino IDE allowing control with only 6 digital I/O lines. Standard Arduino shield dimensions and pinouts. |
 |
K9700 |
|
- Altronics kits are premium do-it-yourself projects designed to be assembled with ease. However, basic electronics knowledge and soldering skills are essential to construct our kits. A difficulty rating is provided to help determine if your ability is sufficient to build the kit project. Please note, once assembly has been commenced we are unable to honor any warranty claims. Please see the full details here.
|
|
(Designed by Altronics) This 4 digit common anode driver board is ideal for building an Arduino controlled clock or counter. It features two on board 74HC595 chips which can be easily driven using Arduino ShiftOut. It utilises all through hole components for easy construction. |
 |
K5117 |
|
- Altronics kits are premium do-it-yourself projects designed to be assembled with ease. However, basic electronics knowledge and soldering skills are essential to construct our kits. A difficulty rating is provided to help determine if your ability is sufficient to build the kit project. Please note, once assembly has been commenced we are unable to honor any warranty claims. Please see the full details here.
|
|
This is the recommended power supply for the K5116 Amplifier Module Kit. |
