|
Description |
Downloads |
Specs |
Ordering |
|
|
A4506 |
|
- With mains power failure the connected batteries are relay switched to the load via two 50A terminals. A sensing circuit disconnects the load when the minimum permissible discharge voltage is reached, thus preventing permanent battery damage. This charger is specifically designed for use on sealed lead acid batteries, gel technology batteries and standard vented lead acid batteries.
|
|
Ideal for PA systems & other applications requiring battery backup. This all new model incorporates a highly efficient, intelligent, multi stage switchmode battery charger ensuring optimum battery charging and performance. |
|
A4450 |
|
- 4 mic/line inputs to 4 zones
- Operates as a matrix mixer or source switcher
- Touchscreen & iOS/Android app control
- RS-485 control via rear panel serial adapter connection
- Adjustable aux level 100mV/1V
- Adjustable balanced mic/line level 3mV/0.7V
- LCD for easy selection of sources to zones
- System cabling via Cat5e UTP.
- Zone and input custom labelling
- Adjustable volume for each input to output selection
- Master & zone source selection wallplates
- 24V DC operation
|
|
This Redback 4x4 audio source matrix system is feature packed yet simple to set up and use it features 4 inputs, selectable to up to 4 zones making it ideally suited to gyms, cafes, restaurants, small clubs and function centres. |
|
A4047 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 100W RMS respectively. |
|
A4370A |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 70V, 100V and 4-16Ω outputs
- 240V AC or 24V DC operation
- 24V DC @ 1 Amp output for external devices
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
This range of booster amplifiers are ideal for installations requiring high power zone amplifiers. Simply choose a power rating according to the wattage required for each zone. |
|
A4432 |
|
- Four Mic/ Line Input channels (Inputs 1-4)
- Four switched RCA AUX Input channels
- Remote AUX source selection, volume and Local input source volume control via optional A 4433 and A 4931 wall plates
- PTT Input and 24V PTT output (limited to 120mA) on inputs 1-4
- Micro SD card based Alert/Evac/Chime/Voice-over module (In built)
- Individual level, bass and treble control on all inputs
- 3.5mm music input overrides AUX 4
- Three levels of priority
- Adjustable Vox sensitivity on inputs 1-4
- Adjustable input sensitivity 1V/100mV on inputs 1-4 and Aux inputs 1-4
- Phantom Power on inputs 1-4
- Tape out (Dual RCA)
- Balanced Output (XLR male)
- Five sets of closing contacts for message triggering (Alert/Evac/Ch1/Ch2/Cancel)
- 24V DC switched output (Limited to 120mA)
- MP3 active indicator
- Signal Present indicator
- LED VU Meter
- 24V DC operation (Plugpack Supplied)
- 24V DC battery back up terminals
|
|
Designed in conjunction with pro-sound contractors, the A 4432 is a stand alone mixer which provides a flexible way to bring multiple audio sources together. It combines many of the best features from our popular mixer and signal processing range into one compact unit. |
|
A4260B NEW
|
|
- Mixer amplifier with in-built SD/USB/FM tuner/Bluetooth music source
- 85% efficient class-D power performance
- Low power consumption & heat generation
- Compact 1RU case
- Bass & treble control
- Front panel mic input
- Protection circuitry
- LED indicators for signal, peak, protection and power
- Selectable 100V line/4-16Ω output
- Mic/Line/Phantom Power options on Mic 1-4
- 24V DC battery backup power input
- Emergency priority input (Mic 1)
- Adjustable VOX muting
|
|
This compact Class-D design amplifier offers multi source mixing plus USB/SD card/FM tuner audio playback and Bluetooth streaming functionality. |
|
A4424 NEW
|
|
- Six mic / line input channels.
- Two outputs via XLR/RCA 1V balanced.
- Level, bass and treble control on all inputs.
- Adjustable input sensitivity.
- Phantom power selection on each input.
- Route signals to each output or both outputs.
- Includes power supply
- 1RU 19” rack mount case.
- Australian designed & assembled
|
|
New to the Redback mixer stable, this model incorporates six inputs which can be routed to 1 of 2 outputs or both as the installation requires. Inputs can be configured for either RCA line level signals or 3 pin XLR balanced mic signals. |
|
A4210 |
|
- Designed to meet AS60118.4-2007
- Coverage up to 180m2
- XLR line & mic inputs
- Aux input via stereo RCA
- EWIS signal connection (RCA)
- Short circuit proof
- Compressor for added speech intelligibility
- Adjustable VOX sensitivity
- Compatible with single loop designs
|
|
Hearing induction loop amplifiers are installed to greatly enhance the listening experience of people using hearing aids. They are commonly installed in public areas which are generally noisy, making it difficult for hearing impaired users to hear clearly. |
|
A4043 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 100W RMS respectively. |
|
C8846B |
|
|
|
Ideal for use with multiple radio microphone systems. This antenna divider eliminates the need for a set of antennas for each system. It utilises a single set of antennas which splits into separate outputs allowing up to four receiver units to operate. T |
|
A4255A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- 3.5mm Jack Input (Front Mounted)
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V AC / 24V DC operation
- Australian designed & manufactured
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation. |
|
A4435A |
|
- Four input channels
- SD card message player for audio announcements
- Individual level, bass and treble control on all inputs
- 3.5mm music input
- Adjustable input sensitivity on mic or line
- 24V DC battery back up terminals
- Four sets of closing contacts for message triggering
- 24V DC switched output
- Message active indicators
- Adjustable Vox sensitivity
|
|
This unique mixer features four input channels which are user selectable for either balanced mic, line or auxiliary use. It incorporates a four channel SD card based message player making it an excellent choice for retail, supermarkets and hardware stores. |
|
A4437 NEW
|
|
- 4 mic or line inputs
- Balanced line or RCA outputs
- VOX priority on input 1 and 2
- Phantom power ON/OFF for mic inputs
- Remote evacuation system muting contacts
- 24V DC operation
- Individual volume, treble and bass for all inputs
- Provision for A4573 alert evac tone generator module
- Australian designed and manufactured.
|
|
Works as a stand alone audio processor with four mic/line inputs for microphone and music sources. When the FIB operates it triggers these contacts, rending the local PA/BGM system inoperative so the main emergency evacuation system has precedence. |
|
A4565A |
|
- Tones conform to AS 1670.4
- Standard 1U 19” rack mount case
- Interfaces with Fire Indicator Boards
- Remote operation of Alert, Evac, Chime, Fire Test, Fire Alarm & Cancel tones
- MP3 based tone playback (with backup hard coded Alert, Evac and Bell tones)
- 24V DC operation
- Auto/Manual/Isolate keyswitch
- Key switch to 003 standard
- Local operation of Alert, Evac and PA
- MP3 based Voice Over messages for Alert and Evac cycles
- Microphone socket for PA use
- Provision for BGM (back ground music)
- Provision for Auxiliary input with front volume control
- Bell chime facility
- Switched 24V DC output for override relays on volume controls
- Switched 24V DC output for strobe operation for Alert mode
- Switched 24V DC output for strobe operation for Evac mode
- Switched 24VDC output for bell mode
- On-board timer for automatic Alert to Evac switchover, adjustable from 30secs to 7.5min in 30 second increments
- Externally operated inputs are activated by switching to ground
- Auxiliary level output
- Suitable for any amplifier with an auxiliary input
- 10 Year Warranty
- Australian Designed and Manufactured
|
|
This easy to operate building alert & evacuation controller controller is designed around industry standard building requirements. When connected to a paging system amplifier, occupants can be alerted and/or evacuated in the event of an emergency eg: fire, gas leak, bomb scare, earthquake. |
|
A4411 |
|
- 2 microphone inputs
- Phantom power on MIc inputs (15V DC)
- 2 line inputs
- Separate tone controls for line and microphones
- Stereo outputs
- 1RU 19” rack mount case
- Master volume on rear panel
- Adjustable line muting
- Front panel mount microphone and line input
- Subwoofer output
- LED VU meter
- VOX active indicator
- Signal Present indicator
- 24V DC input
- 24V DC battery back up terminals
- 10 Year Warranty
- Australian designed & assembled
|
|
This 4 Channel Stereo Mixer has been designed to meet the growing demands of PA systems utilising high power stereo amplifiers, it features 2 balanced microphone and 2 auxiliary inputs. Perfect for aerobics use, bars, bistros, sporting clubs. |
|
A4037 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output (note: this model cannot be converted to 70V line as per others in the series)
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 40W RMS respectively. |
|
A4245A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- 3.5mm Jack Input (Front Mounted)
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V AC / 24V DC operation
- Australian designed & manufactured
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation. |
|
A4567C |
|
- This unit is designed for “loop in loop out” serial wiring to loudspeakers with a 47KΩ terminating resistor at the end of the line. Star wiring or tee offs are prohibited. Each loudspeaker requires a series connected 22µf bipolar capacitor for correct operation. A delay of 10 seconds is provided before registering a fault to minimise false alarms.
|
|
Specifically designed to monitor the condition of 100V line speaker systems in emergency paging and fire evacuation installations. Many large commercial installations have speaker circuits in excess of 250W. |
|
A4250A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- Phantom power
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V AC / 24V DC operation
- Australian designed & manufactured
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation. |
|
A4461 |
|
- Simple touchscreen control selection of zone inputs and level control.
- Changes in selections are reflected on the relevant zone wall plates & main Redback units.
- Adjust custom labelling of zones and inputs on screen.
- Choose button colour theme.
- Fits standard double gang electrical wall box with mounting plate included.
- All glass front bezel for a stylish finish for any room.
- Adjustable screen sleep mode.
- Connects via economical Cat5e UTP cabling.
|
|
These 7" touchscreen control wall plates allow for remote source selection and level control in Redback source control systems (currently compatible with A4450, A4460 and A4650 systems). |
|
A4463 NEW
|
|
- Simple touchscreen control selection of zone inputs and level control.
- Changes in selections are reflected on the relevant zone wall plates & main Redback units.
- Adjust custom labelling of zones and inputs on screen.
- Choose button colour theme.
- Fits standard double gang electrical wall box with mounting plate included.
- All glass front bezel for a stylish finish for any room.
- Adjustable screen sleep mode.
- Connects via economical Cat5e UTP cabling.
|
|
These 7" touchscreen control wall plates allow for remote source selection and level control in Redback source control systems (currently compatible with A4450, A4460 and A4650 systems). |
|
A1937 |
|
- Powered by 24V DC
- 100V line audio output
- Line level audio input
- Short circuit, overload and thermal cutout protection
- Bolt-in chassis construction
|
|
These modules are designed for use in emergency evacuation systems and are powered by an external 24V DC source. They accept a line level audio input and produce a 100V line output via a transformer. The modules feature short circuit, overload and therm |
|
A4235 |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- Overload limiting
- Over voltage limiting
- On demand fan cooling
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V ac / 24V dc operation
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation.
All models include a choice of |
|
A4235A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- Overload limiting
- Over voltage limiting
- On demand fan cooling
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V ac / 24V dc operation
|
|
This compact 30W 1RU rack mount amplifiers is suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. Operates on 240V ac or 24V dc for battery backup operation. |
|
A6530 NEW
|
|
- User programmable buttons & icons
- Multiple screen pages (12 max)
- Tandem operation
- Event splash screens
- Icon library for commonly used buttons
- Infra-red control output
- RS-232 or RS-485 serial outputs
- PIR motion trigger
- Haptic & audible button feedback options
- U/UTP Cat5 cable connection
- Multi-command macros
- IR learning facility
- SD card configuration upload
- Easy to program
|
|
This universal 7" touchscreen wallplate is the perfect control system for commercial and domestic automation. Its stylish low profile design lends itself to installation in new modern homes, classrooms, lecture theatres or corporate boardrooms. |