|
Description |
Downloads |
Specs |
Ordering |
|
|
A3043 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Microphone pre-amp gain: 40dB
- Min load: 4ohm
- Current draw: 2A max.
- Power: 12V dc
- Dimensions: 92.6L x 73.4W x 26.6H mm
- Weight: 160g
|
|
This compact amplifier is a great way to power a pair of speakers without the bulk of a full size hi-fi receiver. It provides 2x15W RMS output power - enough to power a pair of small ceiling or bookshelf speakers. |
|
A3044 |
|
- Input: 6.35mm Dynamic microphone
- Input impedance: 600Ω
- Pre-amplifier Gain: 50dB
- Signal to Noise Ratio: 80dB
- Power Source: 12V DC
- Discreet Mode: MIC 1 (Left) to RCA Left only; MIC 2 (Right) to RCA Right only.
- Mixed mode: Mixed Mono (not stereo) output (MIC 1 + MIC 2 to RCA (L+R)).
- RCA output: Line level 1Vpp~3Vpp (according to MIC Input Level).
- Microphone 6.35mm TRS mono inputs: Not suitable for connection of line level output devices like iPods etc. Mics only.
|
|
Dual microphone preamplifiers that can be mixed in stereo or operated separately. Dual inputs, Dual outputs. Includes 12V power supply. |
|
A3051 |
|
|
|
A low noise pre-amplifier with RIAA equalisation circuitry for connecting your turntable up to a standard auxillary input on a mixer or amplifier. Suitable for use with 'Moving Magnet' pickups. powered by a 9V battery. Compact design fits easily behind an |
|
A3052 |
|
- For all turntables with moving magnet (MM) cartridges or audio devices with line level (e.g. tape decks)
- External housing, reliably shielded against interference
- Top quality circuit technology and components
- Built-in low-noise phono preamp circuit conforms to the RIAA standard
- Power supply included
|
|
This phono preamp can be used to raise your turntable's output to make it compatible with modern amplifiers. At the same time, it adds standardised equalisation. Users may need this phono preamp because their turntable either doesn't have one, in which case they won't be able to play records without one. |
|
A3164 |
|
- Dante Interface for Audio Input.
- RCA output Jacks on front panel.
- Converts Dante Audio Signal to Unbalanced Line Level.
- Selectable Dante Sample Rates: 44.1 kHz ~ 96 kHz.
- High Resolution Digital to Analog Conversion
- Power over Ethernet (PoE).
- Excellent Audio quality
|
|
This device is designed to receive two channels audio signal from the Dante network, and converts to analogue RCA outputs. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to receive the low latency of signal from other devices which already connected on the same Dante network. |
|
A3165 |
|
- Dante Interface for Audio Output
- Terminal Block Input Jack on front panel
- Converts Line Audio Signal to Dante Network
- Input Gain Control on front panel
- Dante Sample Rates Support: 44.1, 48, 88.2, 96KHz
- High Resolution Analog to Digital Conversion
- Power over Ethernet (PoE)
- Excellent Audio quality
|
|
This device is designed to provide two channels audio signal to the Dante network by the Euro terminal input. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to route the low latency of signal to other devices which already connected on the same Dante network. |
|
A3194 |
|
- Allows digital signals to be transmitted using a single Cat5e or Cat6 cable
- Supports multichannel audio
- Select one input from Coaxial or Toslink input ports, and send S/PDIF audio signal to both Coaxial and Toslink output ports simultaneously
- 2 Emitter output connections
- Convenient IR confirmation LED
- Power receptacle with LED indicator
|
|
Allows digital signals to be transmitted using a single Cat5e or Cat6 cable. |
|
A3195A |
|
- Built-in high performance RTOS operating system and
- audio decoder chip; supports DTS/AC-3
- Super fast start time about 3 seconds
- Auto Switch between optical and coaxial channel input
- Auto decode AC-3/DTS (LPCM/PCM/RAW) input signal without any action
- High compatibility
- Small size
- Metal case, Anti-interference
- Headphone port output
- Supports volume adjustment
|
|
This Audio decoder can auto convert optical/coaxial channel (Support LPCM/PCM/RAW) input to 2.0 channel analog audio output, and supports decoding Dolby AC-3/DTS (included 5.1 RAW digital audio streaming). |
|
A3196 |
|
- Output impedance: 16Ω minimum
- THD: 0.05% @ 1kHz
- Power: 5V dc (via micro USB or plugpack)
- Dimensions: 97 x 64 x 30mm
|
|
This single channel headphone amplifier is ideal for systems requiring additional audio level due to impedance differences between the audio source and headphone. |
|
A4017 |
|
- To mount any of the Redback half rack products into a 19" wide racking system, the H 4990 bracket is required. If a single product is mounted into the H 4990, then a metal (H 4992) or plastic (H 4993) infill panel can be fitted for a neater finish.
|
|
Super compact with surprising performance specifications, intended for smaller PA system applications. Our engineering team based the design around a National TDA1519 monolithic IC achieving virtually "destruction proof" operation under quite severe misuse |
|
A4022 |
|
- Balanced microphone input
- Built in VOX muting circuit
- Stereo line inputs
- Bass and treble tone controls
- 240V AC operation
|
|
Designed to meet the requirements of small to medium sized professional public address installations, delivering an output power of 30W RMS. |
|
A4022A NEW
|
|
- Balanced microphone input
- Built in VOX muting circuit
- Stereo line inputs
- Bass and treble tone controls
- 240V AC operation
|
COMING SOONThis item is arriving soon. |
Designed to meet the requirements of small to medium sized professional public address installations, delivering an output power of 30W RMS. |
|
A4024 NEW
|
|
- VOX muting on input 1.
- Balanced microphone inputs.
- Output muting circuit.
- Stereo line inputs & tape output.
- Bass and treble tone controls.
- Output terminals for 100V line and 8 - 16Ω loads
- Over-voltage, over current, thermal run-away and short circuit load protection.
- Muting Features: VOX Muting Via Input 1, Switch Contacts and Output Muting
|
|
A staple of the Redback range since we first started, the 30W amplifier meets the requirements of small to medium public address installations. |
|
A4026 NEW
|
|
- 19" rack system mountable.
- Push to talk (PTT) muting on microphone 1.
- Balanced microphone inputs.
- VOX muting circuit.
- Stereo line inputs & tape output.
- Bass and treble tone controls.
- Output terminals for 100V line and 8 - 16Ω loads
- Over-voltage, over current, thermal run-away and short circuit load protection.
|
|
A staple of the Redback range since we first started, the 30W amplifier meets the requirements of small to medium public address installations. Rack mount version of Redback A 4024. |
|
A4037 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 40W RMS respectively. |
|
A4043 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 100W RMS respectively. |
|
A4047 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 100W RMS respectively. |
|
A4116 |
|
- 15W RMS per channel
- 1 music input (3.5mm)
- 1 auxiliary input
- 4-16Ω output
- 240V ac operation
- Includes Power Supply
|
|
Packed with features, this super compact stereo amp is ideally suited to classrooms, boardrooms, boutiques, reception areas or anywhere a small functional stereo system is required. Designed in close consultation with several leading AV installation compa |
|
A4155 |
|
- Output Power (Stereo 8Ω): 150W + 150W
- TA 1KHz THD≤1% (4Ω): 220W + 220W
- Bridge 8Ω: 440W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <440W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 8.5kg
- Gross Weight: 10.5kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
|
A4157 |
|
- Output Power (Stereo 8Ω): 250W + 250W
- TA 1KHz THD≤1% (4Ω): 370W + 370W
- Bridge 8Ω: 740W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <740W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 9kg
- Gross Weight: 10kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
|
A4159 |
|
- Output Power (Stereo 8Ω): 350W + 350W
- TA 1KHz THD≤1% (4Ω): 500W + 500W
- Bridge 8Ω: 1000W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <440W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 9.5kg
- Gross Weight: 11.5kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
|
A4173 |
|
- Rugged heavy duty construction
- 19” rack mount
- Bridgeable, parallel or two channel stereo operation
- Earth lift switch
- 3 pin XLR and 6.35mm inputs.
- Short circuit protection with indicator
- Overload protection with indicator
- Clipping prevention circuitry with indicator
- Variable speed fan forced cooling
- Muting circuit for switch on/off
|
|
This range is designed to function as a stereo or high power single channel amplifier for use in foreground sound reinforcement ie: pubs, clubs, cinemas and multi-function venues. |
|
A4173A |
|
- Rugged heavy duty construction
- 19” rack mount
- Bridgeable, parallel or two channel stereo operation
- Earth lift switch
- 3 pin XLR inputs.
- Short circuit protection with indicator
- Overload protection with indicator
- Clipping prevention circuitry with indicator
- Variable speed fan forced cooling
- Muting circuit for switch on/off
|
|
This new series dubbed the "Apple" range have been completely redesigned by Biema to offer vastly improved cooling, efficiency and circuit protection. This range is designed to function as a stereo or high power single channel amplifier for use in foreground sound reinforcement ie: pubs, clubs, cinemas and multi-function venues. |
|
A4198 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Headphone output: 105mW RMS per channel
- Headphone distortion: 0.05%
- Min load: 4Ω
- Current draw: 9A max.
- Power: 12V dc
- Dimensions: 205W x 108D x 26Hmm
- Weight: 0.5kg
|
|
Excellent for multi-room audio distribution, this 12V powered four zone amplifier produces 30W RMS per zone (15W RMS per channel) - all from a case just 200mm across! One input source may be connected on the front panel via stereo RCA sockets. |
|
A4199 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Headphone output: 105mW RMS per channel
- Headphone distortion: 0.05%
- Min load: 4Ω
- Current draw: 9A max.
- Power: 12V DC
- Dimensions: 285W x 128D x 43Hmm
- Weight: 0.8kg
|
|
Ideal for small businesses or simple multi-zone home audio systems. Switch between up to 4 different audio sources - connect up to 8 speakers. Toslink digital audio input for TV audio. Great for background music use. Also fitted with 6.35mm microphone connection. |