|
Description |
Downloads |
Specs |
Ordering |
|
 |
A0306A |
|
- Power Rating: 220V - 240VAC
- Power Handling: 2400W
- Max. Load Current: 10AMP
- Pin diameter: 4.76mm per pin
- WARNING: This adapter does NOT convert voltages. For use with 240VAC only.
|
|
On your next holiday don't forget a travel power adaptor to keep you devices fully charged while you're away. This Bali power adapter also works across most parts of Europe. Australia / NZ (Type I) to EU (Type F) plug conversion. |
 |
N2089 |
|
- Heavy duty aluminium case and mounting bracket
- Microchip monitoring and control
- Fully automatic high frequency multi stage charging
- PV solar regulator input
- Compatible with vehicles fitted with smart alternators
- Pulse mode technology that reduces oxidation, evens electrolyte consistency and minimises temperature equating to longer battery life
- Easy push button chemistry select: AGM/Gel, Calcium, LiON, Deep Cycle, VRLA and conventional flooded Lead-Acid batteries
- Internal charger temperature monitoring and power output control
- LED indicators showing state of charge
- Over charging, short circuit and over temperature protection
- Reverse polarity protection: Input reverse polarity protection and Output reverse polarity protection
- Thermal overload protection
- Solar input overload protection
- Power cut memory function; once selected, the charger will remain on this battery type until it is changed
|
|
This 40A DC to DC battery charger with solar charger has been designed for in-vehicle use where auxiliary batteries are required to be charged from solar panels or the vehicles main battery. |
 |
M8936D |
|
- Australian standards compliant
- Suitable for a range of electronic devices
- Compatible with Australian mains power point
|
|
12V DC Switchmode Plugpack Supplied with fixed 2.1mm DC tip (tip positive). Compact design with high current regulated output. Energy authority approved. MEPS approved.
12VDC @ 2A. |
 |
M8561 |
|
- Output short-circuit protection (Auto reset when short circuit is removed)
- Output current-limiting and over-voltage protection
- Separate standby battery circuit with fast changeover
- Standby battery voltage shutdown below 10.8V DC
|
|
A complete 12V dc power supply and battery backup in one compact enclosure. When operating from 240V, it automatically charges the internal battery (available separately) and powers the connected load (max 5A). When mains fails, the load switches and is p |
 |
M8937D |
|
- Australian Standards Compliant
- Suitable for a range of electronic devices
- Compatible with Australian mains power point
|
|
12V DC Switchmode Plugpack Supplied with fixed 2.1mm DC positive tip. Compact design with high current regulated output. Energy authority approved. MEPS approved.
12VDC @ 3A.
|
 |
D0882A |
|
- Line interactive smart AVR
- Three UPS backup / Surge protected Australian outlets
- Three Surge protected Australian outlets
- Full time power surge / spike protection
- USB communications with sophisticated PowerShield NetGuard software
- Modern, stylish steel enclosure
- Ultra reliable
|
|
Designed to support multiple computers and peripherals, networked PC's and point of sale systems. In the event of a power outage the UPS will allow continued operation of the PC so that work can be saved and the system can be shutdown safely. Generally, |
 |
M8932B |
|
- Australian standards compliant
- Suitable for a range of electronic devices
- Compatible with Australian mains power point
|
|
12V DC Switchmode Plugpack Supplied with fixed positive to tip 2.1mm DC jack. Compact design with high current regulated output. Energy authority approved. MEPS approved.
12VDC @ 1A. |
 |
D0881 |
|
- Stylish and informative LCD display
- Surge Protection, Best in it’s Class
- Excellent microprocessor control guarantees high reliability
- Australian outlet sockets for UPS and Surge protection
- Buck and boost AVR for voltage stabilization
- User replaceable batteries
- Silent operation (no fans included)
- Auto restart when AC returns
- Off-mode charging
- Cold start function
- USB communication with sophisticated NetGuard® software
- Free download software included
|
|
The Powershield Defender PSD 650VA Uninterruptible Power Supply (UPS) is designed to support multiple computers and peripherals, networked PC''s and point of sale systems. |
 |
N2097 |
|
- Suitable for any 12VDC system up to 8A direct current loads like motors, lamps, heaters & LEDs (with current limiting resistors).
- Electric motor can start smoothly at low speed with this PWM controller.
- Replaces the resistor circuit for control of the speed of DC motors
- Frequently used as light dimmer.
- Energy efficient with zero to full speed control
- Light dimmer capable of smooth control
- The whole PCBA is potted in epoxy and with the special splash proof tuning potentiometer making this controller weather proof.
|
|
This 12VDC 8A pulse width modulator (PWM) is a general purpose DC output power control. |
 |
D0883 |
|
- Line interactive smart AVR
- Three UPS backup / Surge protected Australian outlets
- Three Surge protected Australian outlets
- Full time power surge / spike protection
- USB communications with sophisticated PowerShield NetGuard software
- Modern, stylish steel enclosure
- Ultra reliable
|
|
Designed to support multiple computers and peripherals, networked PC's and point of sale systems. In the event of a power outage the UPS will allow continued operation of the PC so that work can be saved and the system can be shutdown safely. Generally, |
 |
N2099A |
|
- Receive notification alerts when Bluetooth in range
- Check vehicle cranking system automatically while engine starting
- Check charging system (alternator)
- List driving periods
- Alert smartphone if abnormalities occur.
- Short-circuit and reverse connection protection
- Data stored in battery monitor for up to 31 days
- Automatic synchronisation when in Bluetooth range
- Compatible with all 12V vehicle batteries
- Graphical historical data display
- Engine starting detection automatically
- Free BM2 app for both iOS and Android devices
|
|
This handy 12V bluetooth battery monitor allows you to get live performance stats on your phone. Provides live feedback on your vehicle or auxiliary battery, plus long term stats. Suits lead acid batteries. |
 |
D0873 |
|
- Automatic Voltage Regulation (Buck and Boost)
- Light-weight compact and elegantly designed
- Intelligent microprocessor control
- Monitoring and shutdown software included
- Fax/modem/LAN surge suppression port
- Overload protection and alarm
- Output short circuit protection
- Start on battery function (cold start)
- USB communication
- Easy user replaceable battery
- Australian/New Zealand approved sockets
- Wall mountable
- Fast charging – 90% in 4 hours
|
|
The Office model is perfect for a home/office solution. It includes three battery backup and surge protected Australian sockets, three dedicated Australian outlets with surge protection and RJ45 phone line surge protection. Provides modified sinew |
 |
M6014 |
|
|
|
Typically used for garden lighting and water feature pumps these power supplies are ideal for outdoor use. |
 |
P0455 ROHS
|
|
|
|
Battery snap clip to suit 9V batteries. These can also be used to connect to some of our battery holders which include an integral battery snap. |
 |
M8181 |
|
- Input: 230V AC 50Hz.
- Output: 110V AC 75W.
- Cable: 1.8m.
- Continuous usage must be below 65VA on M8181
|
|
Converts 220V-240V to 110V for using US appliances on Australian mains voltages. Fitted with US mains socket. |
 |
M8821 |
|
- Output
- Output voltage: +5.1V DC
- Minimum load current: 0A
- Nominal load current: 3.0A
- Maximum power: 15.3W
- Load regulation: ±5%
- Line regulation: ±2%
- Ripple & noise: 120mVp-p
- Rise time: 100ms maximum to regulation limits for DC outputs
- Turn-on delay: 3000ms maximum at nominal input AC voltage and full load
- Protection: Short circuit protection, Overcurrent protection, Over temperature protection
- Efficiency: 81% minimum (output current from 100%, 75%, 50%, 25%), 72% minimum at 10% load
- Output cable: 1.5m 18AWG
- Output connector: USB Type-C
- Input
- Voltage range: 100-240Vac (rated), 96-264Vac (operating)
- Frequency: 50/60Hz ±3Hz
- Current: 0.5A maximum
- Power consumption (no load): 0.075W maximum
- Inrush current: No damage shall occur and the input fuse shall not blow
|
|
Official Raspberry Pi power supply, ideal for use with the Raspberry Pi 4 Model B board. This power supply comes with USB Type C lead and AU mains plug. It supports up to 3A of current to power devices through four USB ports on the board. |
 |
S4532 |
|
- General
- Dimensions: 90L x 70W x 107H mm (including tabs)
- Weight: 1.45kg
- Capacity
- 20 Hour Rate (10.5V): 4.5Ah
- 10 hour Rate (10.5V): 4.2Ah
- 1 Hour Rate (9.60V): 2.95Ah
- Capacity Affected by Temperature
- 40°C: 102%
- 25°C: 100%
- 0°C: 85%
- -15°C: 65%
- Charging
- Internal Resistance: Approximately 45MΩ
- Float Charging Voltage: 13.6 - 13.8V @ 25°C (temperature compensation: -18mV/°C)
- Cyclic Charging Voltage: 14.50 - 15V @ 25°C (temperature compensation: -30mV/°C)
- Maximum Charging Current: 1.35A
- Maximum Discharging Current: 67.5A (5 sec.)
- Designed Floating Life: 5 years.
|
|
This 12V 4.5Ah sealed lead acid (SLA) battery is a compact battery for powering 12V equipment. |
 |
SL4578A
|
|
|
|
This 12.8V 120Ah lithium battery (LiFePO4) is compatible in size with traditional 90-130Ah SLA batteries (check dimensions), but with all the benefits of cutting edge lithium technology. |
 |
M8195B
|
|
- Compact design with 20000mAh internal battery pack
- 2500A peak current output for jumpstarting 4, 6 and 8 cylinder vehicles (inc diesels).
- Includes DC output with cigarette lighter socket lead for powering car fridge, lighting, and other portable 12V appliances.
- Includes heavy duty battery clamps, USB type C charging cable and DC to Car Accessory socket adapter
- Supplied with hard wearing zip up carry case.
- Dual USB charging outputs (5V/3A each)
- 1W LED torch
|
|
This lithium battery pack is suitable for jump starting 12V battery equipped vehicles such as cars, 4WDs and agricultural equipment. |
 |
A0289A |
|
- Charges 2 cells at once
- Charging / Fully charged indication
- Powered by any USB charger at home or in the car
- Compatible with Lithium-Ion, NiMH and NiCd cells
- Over-charge protection
- Short-circuit protection
- Reverse polarity protection
- 0V activation function to charge the Li-ion cells with Protection PCB design
|
|
This compact USB battery charger gives you the flexibility of charging both lithium ion (Li-Ion), nickel metal hydride (Ni-MH) and nickel cadmium (Ni-Cd) cells. USB charging allows it to be connected to any mains or car charger. |
 |
M8305 |
|
- Input voltage: a.c. 220-240V @ 50Hz
- Output voltage: 0 - 30V d.c.
- Output current max: 5A
- Supply regulation: CV≤1%+10mV
- Load regulation: CV≤1%+5mV
- Ripple: 200mVp-p
- Protection: Current limiting
- Voltmeter: LCD ±1% +2 digits
- Ammeter: LCD ±1% +2 digits
- Temperature: 0ºC-40ºC
- Humidity: Less than RH80%
- Operating time: 8hrs
- Dimensions: 85 x 160 x 205mm
|
|
A compact, efficient bench top power supply for use in servicing, repair and design of electronics. The low noise switchmode design offers excellent regulation for low current requirements. |
 |
S4538 |
|
- General
- Dimensions: 151L x 65W x 102H mm (including tabs)
- Weight: 2kg
- Charging
- 20 Hour Rate (10.5V): 7Ah
- Cell Per Unit: 6
- Nominal Voltage: 12V
- Internal Resistance: Approximately 28MΩ
- Max Discharge Current: 70A (5s)
- Battery Life: 3-5 years (standby)
- Terminal Type: 4.8mm/F1
- Container Material: ABS
- Max Charge Current: 2.1A
- Charge Voltage: 14.4V to 15V
- Standby (float) Charge Voltage: 13.5V to 13.8V
- Ambient Temperature
- Charge: 0°C to 40°C
- Discharge: -15°C to 50°C
- Storage: -15°C to 40°C
|
|
Premium grade, long life, maintenance free sealed lead acid batteries. Cells are fully sealed to prevent leakage of electrolyte. |
 |
S4543 |
|
- General
- 151L x 65W x 100H mm (including tabs)
- Weight: 2.65kg
- Charging
- 20 Hour Rate (10.5V): 9Ah
- Cell Per Unit: 6
- Nominal Voltage: 12V
- Internal Resistance: Approximately 18MΩ
- Max Discharge Current: 135A (5s)
- Battery Life: 3-5 years (standby)
- Terminal Type: 6.3mm/F2
- Container Material: ABS
- Max Charge Current: 2.52A
- Charge Voltage: 14.4V to 15V
- Standby (float) Charge Voltage: 13.5V to 13.8V
- Ambient Temperature
- Charge: 0°C to 40°C
- Discharge: -15°C to 50°C
- Storage: -15°C to 40°C
|
|
This 12V 9Ah sealed lead acid (SLA) battery is a compact battery for powering 12V equipment. |
 |
SL4541A
|
|
|
|
This 8Ah LiFEPO4 replacement battery is compatible in size with traditional 7Ah/9Ah SLA batteries, but with all the benefits of cutting edge lithium technology. |
 |
S4540 |
|
- General
- Dimensions: 151L x 65W x 100H mm (including tabs)
- Weight: 2.2kg
- Capacity
- 20 Hour Rate (10.5V): 7.2Ah
- 10 Hour Rate (10.5V): 6.7Ah
- 1 Hour Rate (9.6V): 4.67Ah
- Capacity Affected by Temperature
- 40°C: 102%
- 25°C: 100%
- 0°C: 85%
- -15°C: 65%
- Charging
- Internal Resistance: <25mΩ
- Float Charging Voltage: 13.6 - 13.8V @ 25°C (temperature compensation: -18mV/°C)
- Cyclic Charging Voltage: 14.50 - 15V @ 25°C (temperature compensation: -30mV/°C)
- Maximum Charging Current: 2.16A
- Maximum Discharging Current: 108A (5 sec.)
- Designed Floating Life: 5 years.
|
|
This 12V 7.2Ah sealed lead acid (SLA) battery is perhaps the most common size SLA battery in use. |
 |
P8420A |
|
- Fitted with IEC C14 Plug and 3 pin mains appliance connectors.
- 30cm length.
- 3 x 1mm2 conductors
- Electrical authority approved.
- AS/NZS standards compliant for connectors & cable.
|
|
This 10A IEC C14 to 3 pin Australian mains socket power cord is commonly used on UPS back up systems and PDUs. |
 |
M8182 |
|
- Input: 230V AC 50Hz.
- Output: 110V AC 100W.
- Cable: 1.8m.
- Continuous usage must be below 70VA
|
|
Converts 240V to 120V for using US appliances on Australian mains voltages. Fitted with US mains socket. |
 |
S4975
|
|
|
|
Long life lithium battery in 14250 half AA size. |
 |
M8610 |
|
|
|
Supplied pre-terminated in a 30cm loop with mating SAE bullet connectors on each end. 18AWG cable 7.5A rated. |
 |
SL4576W
|
|
|
|
These slimline lithium (LiFePO4) batteries are for situations where space is at a premium these compact mountable batteries measure just 65mm high and weigh just 20kg. |
 |
S4984
|
|
- Typical Capacity: 720mAh @ 0.2C discharge
- Minimum Capacity: 700mAh @ 0.2C discharge
- Nominal voltage: 3.7V
- Standard Charge: CC/CV, 0.2C5A, 4.20V
- Standard Discharge: CC, 0.2C5A, 3.00V
- End-of-Charge Voltage: 4.20V
- End-of-Charge Current: 0.02C5A (At CV Mode)
- Charging Time: 8 hours (standard charging)
- Quick Charge Current: 700mA (1.0C5 rate) 1C
- Quick Discharge Current: 1400mA (2.0C5 rate) 2C
- Max Discharge Current: 2100mA (3.0C5 rate) 3C
- Initial Impedance: 75mΩ max.
- Weight: 17g
- Charging Operating Temperature: 0°C to 45°C
- Discharging Operating Temperature: -20°C to 60°C
- Storage Temperature: -5°C to 35°C
- Storage Humidity: Less than 75% RH
- Standard Environmental Conditions: 25°C @ 45-75% RH, 86-106KPA.
|
|
These high performance RCR123A lithium ion 3.7V batteries offer high performance and long life from a compact package. This model has in-built protection features to ensure safe operation at all times. These include over charge, over discharge, short circuit and over current protection. |
 |
A0712 |
|
- Operating voltage: 12V battery
- Maximum switching current: 20A with cooling, 10A no cooling
- Switching voltage: 10.4V - 13.3V
- Reset voltage: 0.8V±0.3V above switching voltage
- Cutoff device: powerMOS transistor in the negative line
- Device current consumption: <0.7mA in OFF condition, <1.6mA in ON condition (LED lights)
- Dimensions: 87W x 60D x 33Hmm including mounting flanges
|
|
This battery saver protects your 12V car battery from discharge by disconnecting loads to prevent voltage dropping below a preset limit (10.4 to 13.3V). The module automatically reconnects the loads once the battery recharges, typically 0.8V above cut-off |
 |
A0346 |
|
- Kit includes 1 RF remote + 1 outlets
- RF Remote control means line-of-sight is not necessary
- Outlets work hidden behind equipment and cabinets!
- Outlet's channel is programmable (CH1-4)
- Multiple outlets can share the same channel to be controlled simultaneously
- Saves stand-by power
- Saves from your electricity bill
- Can be used in conjunction with a power board
- Built-in receiver memory stores data for up to 10 years
- Turn individual receivers on or off or a single button to turn all receivers on or off at the same time
|
|
Cut standby 240V power usage around the home and office by switching appliances off at the wall via remote control. Easy inline connection between the GPO and your appliance. |
 |
S4987B
|
|
- GP Code: CR1225
- Capacity (mAh): 125
- Chemistry:Lithium
- Dimensions (mm): 12 x 2.5
- Voltage: 3V
|
|
These High-Grade Lithium 3V "button batteries" are used in many items ranging from watches, calculators to toys and portable hand-held appliances. |
 |
M6010 |
|
|
|
Typically used for garden lighting and water feature pumps these power supplies are ideal for outdoor use. |
 |
D0884 |
|
- Offering the best protection in its class, protecting against damaging surges
- Modern, stylish LCD display indicates voltage in/out, amount of load and remaining capacity
- The AVR automatically bucks/boosts unstable fluctuating utility voltages, bringing them within 10% of nominal voltage range and thereby protecting valuable equipment
- Compact design at just 230mm deep
- Intelligent slot for SNMP communications card
- Battery is easily hot swappable and user replaceable
- Designed to run cool without fans
- After an extended power outage the UPS will turn back on and resume equipment functionality once power has returned
- Allows for orderly shutdown without software
- Free, downloadable NetGuard software provides complete power monitoring
- The plugged in UPS will continue to charge internal batteries whether the unit is on or off
- Comes standard with 6 Australian sockets and 2 IEC outlets. Of the 6 Australian outlets, 4 can be used with plug packs
- The UPS can turn on equipment when it is off, simply by connecting equipment and turning the UPS on
- Plug and play on any computer or NAS drive
|
|
This UPS 800VA Defender Rack Mount expands the successful Defender Range by building the popular features into a Rack Mount
UPS. At 230mm deep, this is the perfect UPS for shallow, wall mounted Comms cabinets.
This versatile UPS uses Automatic Voltage Regulation (AVR) to minimise the effects of fluctuations in input voltage, protecting
your valu |
 |
S4550 |
|
- General
- Dimensions: 181L x 76W x 167H mm (including tabs)
- Weight: 5.4kg
- Charging
- Cell Per Unit: 6
- Nominal Voltage: 12V
- Nominal Capacity: 18Ah @ 20hour rate.FV (1.75/Cell)
- Internal Resistance (1KHz): ≤16mΩ
- Max. Discharge Current: 180A (5s)
- Battery Life: 3-5 years standby
- Terminal Type: M5/F13
- Container Material: ABS
- Ambient Temperature
- Charge: 0°C to 40°C
- Discharge: -15°C to 50°C
- Storage: -15°C to 40°C
- Max Charge Current
- Cycle Use:
- Max Charge Current: 5.4A
- Charge Voltage: 14.4V to 15.0V
- Stand By:
- Charge Voltage: 13.5V to 13.8V
|
|
This 12V 18Ah sealed lead acid (SLA) battery is a compact battery for powering 12V equipment. |
 |
T5098
|
|
- Suits batteries up to 100Ah
- Dual 50A Anderson Plugs
- 12V Cigarette Socket
- 2 x 50A maxi blade fuses in circuit for extra protection.
- Lid with dual side clips for extra secure fit.
- Dual USB Ports with high current output (2 x 2.4A)
- Handy bar graph LED Voltmeter
- Circuit Breaker Switch
|
|
This 12V battery box features all the common connections that would typically be required for outdoor recreation power needs. |
 |
M8911B |
|
- Australian standards compliant
- Suitable for a range of electronic devices
- Compatible with Australian mains power point
|
|
5V DC Switchmode Plugpack Supplied with fixed 2.1mm DC jack. Compact design with high current regulated output. Energy authority approved. MEPS approved.
5VDC @ 4A. |
|
SL4580W
|
|
|
|
These slimline lithium (LiFePO4) batteries are for situations where space is at a premium these compact mountable batteries measure just 65mm high and weigh just 25kg. |
 |
M8538 |
|
- Simple plug and charge operation
- Can be left permanently on charge
- Interchangeable charge leads
- Includes crocodile clip and ring terminal connections
- Two state LED charge indicator
- Ideal for charging back up auxiliary batteries and LiFePO4 battery powered vehicles, scooters etc.
|
|
This compact charger is suitable for charging Lithium Iron Phosphate batteries (LiFePO4 type) from mains power. |
 |
S4724
|
|
- Rated for 2C continuous discharge
- Great energy retention with low self-discharge rates (<8% per month)
- Reliable under extreme conditions
- Standard 2-pin JST-PH connector
|
|
Polymer Lithium Ion batteries offer superior energy density.
With a cell voltage of 3.7 Volts, these batteries are perfect for microcontrollers and other low power devices, especially when paired with a good DC/DC regulator for logic level output. |
 |
M8303 |
|
- Input voltage: a.c. 220-240V @ 50Hz
- Output voltage: 0 - 30V d.c.
- Output current max: 3A
- Supply regulation: CV≤1%+10mV
- Load regulation: CV≤1%+5mV
- Ripple: 200mVp-p
- Protection: Current limiting
- Voltmeter: LCD ±1% +2 digits
- Ammeter: LCD ±1% +2 digits
- Temperature: 0ºC-40ºC
- Humidity: Less than RH80%
- Operating time: 8hrs
- Dimensions: 85 x 160 x 205mm
|
|
A compact, efficient bench top power supply for use in servicing, repair and design of electronics. The low noise switchmode design offers excellent regulation for low current requirements. |
 |
S4491 |
|
- Capacity
- 20 Hour Rate (5.25V): 4.5Ah
- 10 Hour Rate (5.25V): 4.2Ah
- 1 Hour Rate (4.8V): 2.95Ah
- Capacity Affected by Temperature
- 40°C: 102%
- 25°C: 100%
- 0°C: 85%
- -15°C: 65%
- Charging
- Internal Resistance: Approximately 25MΩ
- Float Charging Voltage: 6.8 - 6.9V @ 25°C (temperature compensation: -9mV/°C)
- Cyclic Charging Voltage: 7.25 - 7.5V @ 25°C (temperature compensation: -15mV/°C)
- Maximum Charging Current: 1.35A
- Maximum Discharging Current: 67.5A (5 sec.)
- Designed Floating Life: 5 years.
- General
- Dimensions: 70L x 47W x 107H mm (including tabs)
- Weight: 0.75kg
|
|
This 6V 4.5Ah sealed lead acid (SLA) battery is a compact battery for powering 6V equipment. |
 |
D0934 |
|
- Very wide input voltage range
- Excellent output voltage stability
- Includes surge and spike suppression
- Extremely fast response
- Provides over-voltage & under-voltage protection
- Provides over-temperature and overload protection
- Stylish enclosure with Australian outlet sockets
|
|
The PowerShield VoltGuard AVR automatically maintains a constant voltage level to protect sensitive electronics from brownouts and over voltages.
|
 |
M8169 |
|
- High efficiency: 95.5%
- Input reversing polarity protection
- Input transient absorption protection
- Support -40°C environment
- 100% full load burn in test
- IP65 rating
- Over current, over temperature and short circuit protection
- Non-isolated module
|
|
This converter provides a regulated 12V d.c. output at a maximum of 30A from a typical 24V battery. Dimensions: 110x70x23mm |
 |
D0885A |
|
- Pure Sine Wave Output
- Output Power Factor 0.9
- Free, programmable Power Management
- Ultra Modern, Informative LCD – Shows Battery Time Remaining
- ECO Mode
- Smart AVR
- Emergency Power Off Function
- Multiple Communication Available with faster SNMP Card
|
|
D 0885A 2000VA The Commander series provide mains like pure sine wave for powering devices with less heat generation and high efficiency. Perfect for servers, motor driven equipment and sensitive equipment requiring a perfect sinewave to operate cor |
 |
M8254 |
|
- Up to 20A output
- Fixed 13.8V voltage
- High efficiency switchmode design
- Low noise and ripple <100mV
- 2% voltage regulation
- Short circuit protected output
- Fused input
|
|
A fixed voltage output power supply designed for powering automotive, marine and comms equipment. |
 |
SL4581A
|
|
|
|
This 12V 150Ah LiFEPO4 replacement battery is compatible in size with traditional 150Ah SLA batteries, but with all the benefits of cutting edge lithium technology. |
 |
M8968C |
|
- Australian standards compliant
- Suitable for a range of electronic devices
- Compatible with Australian mains power point
|
|
24V DC Switchmode Plugpack Supplied with fixed 2.1mm DC tip (tip positive). Compact design with high current regulated output. Energy authority approved. MEPS approved.
24VDC @ 1A. |
This product poses a serious health hazard if swallowed. If swallowed you must go to emergency immediately.