|
Description |
Downloads |
Specs |
Ordering |
|
 |
A4155 |
|
- Output Power (Stereo 8Ω): 150W + 150W
- TA 1KHz THD≤1% (4Ω): 220W + 220W
- Bridge 8Ω: 440W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <440W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 8.5kg
- Gross Weight: 10.5kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4157 |
|
- Output Power (Stereo 8Ω): 250W + 250W
- TA 1KHz THD≤1% (4Ω): 370W + 370W
- Bridge 8Ω: 740W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <740W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 9kg
- Gross Weight: 10kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4159 |
|
- Output Power (Stereo 8Ω): 350W + 350W
- TA 1KHz THD≤1% (4Ω): 500W + 500W
- Bridge 8Ω: 1000W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <440W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 9.5kg
- Gross Weight: 11.5kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4173 |
|
- Rugged heavy duty construction
- 19” rack mount
- Bridgeable, parallel or two channel stereo operation
- Earth lift switch
- 3 pin XLR and 6.35mm inputs.
- Short circuit protection with indicator
- Overload protection with indicator
- Clipping prevention circuitry with indicator
- Variable speed fan forced cooling
- Muting circuit for switch on/off
|
|
This range is designed to function as a stereo or high power single channel amplifier for use in foreground sound reinforcement ie: pubs, clubs, cinemas and multi-function venues. |
 |
A4173A |
|
- Rugged heavy duty construction
- 19” rack mount
- Bridgeable, parallel or two channel stereo operation
- Earth lift switch
- 3 pin XLR inputs.
- Short circuit protection with indicator
- Overload protection with indicator
- Clipping prevention circuitry with indicator
- Variable speed fan forced cooling
- Muting circuit for switch on/off
|
|
This new series dubbed the "Apple" range have been completely redesigned by Biema to offer vastly improved cooling, efficiency and circuit protection. This range is designed to function as a stereo or high power single channel amplifier for use in foreground sound reinforcement ie: pubs, clubs, cinemas and multi-function venues. |
 |
A4198 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Headphone output: 105mW RMS per channel
- Headphone distortion: 0.05%
- Min load: 4Ω
- Current draw: 9A max.
- Power: 12V dc
- Dimensions: 205W x 108D x 26Hmm
- Weight: 0.5kg
|
|
Excellent for multi-room audio distribution, this 12V powered four zone amplifier produces 30W RMS per zone (15W RMS per channel) - all from a case just 200mm across! One input source may be connected on the front panel via stereo RCA sockets. |
 |
A4199 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Headphone output: 105mW RMS per channel
- Headphone distortion: 0.05%
- Min load: 4Ω
- Current draw: 9A max.
- Power: 12V DC
- Dimensions: 285W x 128D x 43Hmm
- Weight: 0.8kg
|
|
Ideal for small businesses or simple multi-zone home audio systems. Switch between up to 4 different audio sources - connect up to 8 speakers. Toslink digital audio input for TV audio. Great for background music use. Also fitted with 6.35mm microphone connection. |
 |
A4201 |
|
- SPECIFCATIONS:
- Power Output: 50 Watts RMS x 2 into 8 ohm
- Total Harmonic Distortion: <0.01% @30W; <5.0% @50W
- Minimum Speaker Impedance: 6 ohm
- Signal-to-Noise Ratio: 103 dB, A weighted
- Input Impedance: 2k ohm ± 5%
- Frequency response: 20-20,000 Hz
- Channel Separation: 95 dB
- Efficiency: 85%
- Dynamic Range: >100 dB
- Electrical Requirement: 24V DC @ 5A centre pin positive
- Dimensions: 50H x 86W x 143D mm
- Weight: 455g
- BLUETOOTH SPECIFICATIONS:
- Bluetooth version: BT V5.0
- Analog input sensitivity: 1-2V RMS
- Bluetooth range: 30m (line of sight)
- Decoding: SBC, MP3, AAC
- Output: A2DP, AVRCP
|
|
A compact, sturdy 2x50W RMS class-D stereo amplifier with 3.5mm input on the front and RCA input on the back for easy connection. |
 |
A4205 |
|
- Designed to meet AS60118.4-2007
- Suits small booths 2-3 square metres
- XLR mic input
- Compatible with single loop designs
- Aux input via stereo RCA
- 10 year warranty
- Australian designed & assembled
- Short circuit proof
- Compressor circuitry
|
|
This compact hearing loop amplifier is designed for use in information kiosks, ticketing booths, help desks etc. Anywhere a small loop system is required to aid the hearing impaired. Engineered to meet AS60118.4-2007. A balanced mic input and stereo line auxiliary input is provided. Compact half rack 1RU case. 24V DC operation. |
 |
A4209 |
|
|
|
Pack of 5 indicator labels to inform patrons that there is a hearing aid induction loop installed. 140H x 100W mm |
 |
A4210 |
|
- Designed to meet AS60118.4-2007
- Coverage up to 180m2
- XLR line & mic inputs
- Aux input via stereo RCA
- EWIS signal connection (RCA)
- Short circuit proof
- Compressor for added speech intelligibility
- Adjustable VOX sensitivity
- Compatible with single loop designs
|
|
Hearing induction loop amplifiers are installed to greatly enhance the listening experience of people using hearing aids. They are commonly installed in public areas which are generally noisy, making it difficult for hearing impaired users to hear clearly. |
 |
A4212 |
|
- Designed to meet AS60118.4-2007
- Coverage up to 650m2
- XLR line & mic inputs
- Aux input via stereo RCA
- EWIS signal connection (RCA)
- Short circuit proof
- Compressor for added speech intelligibility
- Adjustable VOX sensitivity
- Compatible with single loop designs
|
|
Hearing induction loop amplifiers are installed to greatly enhance the listening experience of people using hearing aids. They are commonly installed in public areas which are generally noisy, making it difficult for hearing impaired users to hear clearly. |
 |
A4230A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- Phantom power
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V ac / 24V dc operation
- Australian designed & manufactured
|
|
Utilising only 1RU of rack space, this range of Redback power amplifiers is available in three power ratings of 30W, 60W and 100W RMS. They lend themselves perfectly for installations requiring individual zone amplifiers. |
 |
A4235 |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- Overload limiting
- Over voltage limiting
- On demand fan cooling
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V ac / 24V dc operation
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation.
All models include a choice of |
 |
A4235A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- Overload limiting
- Over voltage limiting
- On demand fan cooling
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V ac / 24V dc operation
|
|
This compact 30W 1RU rack mount amplifiers is suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. Operates on 240V ac or 24V dc for battery backup operation. |
 |
A4240A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- Phantom power
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V AC / 24V DC operation
- Australian designed & manufactured
|
|
These compact 1RU rack mount ampliers are suitable for both stand alone PA system use, or as zone ampliers in
larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation. |
 |
A4245A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- 3.5mm Jack Input (Front Mounted)
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V AC / 24V DC operation
- Australian designed & manufactured
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation. |
 |
A4250A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- Phantom power
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V AC / 24V DC operation
- Australian designed & manufactured
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation. |
 |
A4255A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- 3.5mm Jack Input (Front Mounted)
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V AC / 24V DC operation
- Australian designed & manufactured
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation. |
 |
A4260B NEW
|
|
- Mixer amplifier with in-built SD/USB/FM tuner/Bluetooth music source
- 85% efficient class-D power performance
- Low power consumption & heat generation
- Compact 1RU case
- Bass & treble control
- Front panel mic input
- Protection circuitry
- LED indicators for signal, peak, protection and power
- Selectable 100V line/4-16Ω output
- Mic/Line/Phantom Power options on Mic 1-4
- 24V DC battery backup power input
- Emergency priority input (Mic 1)
- Adjustable VOX muting
|
|
This compact Class-D design amplifier offers multi source mixing plus USB/SD card/FM tuner audio playback and Bluetooth streaming functionality. |
 |
A4262B NEW
|
|
- Mixer amplifier with in-built SD/USB/FM tuner/Bluetooth music source
- 85% efficient class-D power performance
- Low power consumption & heat generation
- Compact 1RU case
- Bass & treble control
- Front panel mic input
- Protection circuitry
- LED indicators for signal, peak, protection and power
- Selectable 100V line/4-16Ω output
- Mic/Line/Phantom Power options on Mic 1-4
- 24V DC battery backup power input
- Emergency priority input (Mic 1)
- Adjustable VOX muting
|
|
These compact Class-D design amplifiers offer multi source mixing plus USB/SD card/FM tuner audio playback and Bluetooth streaming functionality. |
 |
A4270 |
|
- Multi-stage thermally cued fan cooling
- 2U 19” rack mount (with optional A 4376)
- Tape record out terminals
- Provision for connection to Redback A4660 touchscreen paging console
- MP3 based Alert/Evac tones with MP3 voice over message for emergency tones (built in)
- 3 mic input and 4 auxiliary inputs
- Phantom powering available on all inputs
- Adjustable vox muting on inputs 1 & 2.
- Bass and treble tone controls
- Terminals for 100V line output
- 240V AC or 24V DC power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- Australian designed & assembled
|
|
Similar in functionality to the recently released A 4377/A4387 amplifiers with the addition of four 100V line output zones. |
 |
A4275C |
|
- Very low noise and distortion
- Thermal overload protection
- Thermally cued forced fan cooling
- Protect Mode
- 4 levels of priority/Vox muting
- LCD display of amplifier status
- Minimum and Maximum Master Volume Over-ride
- Minimum and Maximum Remote Volume Over-ride
- USB keyboard interface for labelling of inputs and installer contact details. • 6 inputs configurable as balanced microphone or line
- Music Input on front panel
- Adjustable line level sensitivity
- 70V, 100V and 4-16ohm outputs
- 240V AC or 24V DC operation
- 300mA Backup Battery charging
- Phantom power (on microphone inputs)
- Tape out (Dual RCA)
- Pre-amp send and return connections (RCA)
- Balanced line output (3 pin male XLR)
- Remote Volume option
- 24V switched output via PTT microphone (not supplied)
- 19” Rack Mount (2 unit).
- Optional Alert/Evac tones with voice-over message (via A 4573 module)
- Optional MP3 input with remote control (via A 2711 module)
|
|
Engineered for professional PA installations, the A 4275C conservatively delivers 125W RMS power. Including three levels of input priority, bass and treble controls and phantom powering capability enable unparalleled flexibility for a wide scope of applications such as schools, shopping centres, workshops, mine sites and office buildings. |
 |
A4280 |
|
- Multi-stage thermally cued fan cooling
- 2U 19” rack mount (with optional A 4376)
- Tape record out terminals
- Provision for connection to Redback A4660 touchscreen paging console
- MP3 based Alert/Evac tones with MP3 voice over message for emergency tones (built in)
- 3 mic input and 4 auxiliary inputs
- Phantom powering available on all inputs
- Adjustable vox muting on inputs 1 & 2.
- Bass and treble tone controls
- Terminals for 100V line output
- 240V AC or 24V DC power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- Australian designed & assembled
|
|
Similar in functionality to the recently released A 4377/A4387 amplifiers with the addition of four 100V line output zones. |
 |
A4285C |
|
- VU meter on LCD screen
- Output peak limited
- Multi-stage thermally cued fan cooling
- 2U 19" rack mount
- Tape record out terminals
- Remote volume facility
- Optional alert, evac & chime tone generator (A 4573)
- Vox activated 24V dc output
- 6 inputs with 3 pin XLR or 2 x RCA sockets
- Phantom powering available on all inputs
- Three levels of priority
- Option for mic/line to operate vox muting on inputs 1 to 3
- Push to talk (PTT) terminals on rear panel
- Bass and treble tone controls
- Power amp line out connector
- Terminals for 100V line, 70V line and 4 - 16Ω loads
- 240V ac or 24V dc power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- 300mA trickle charge facility for 24V dc batteries
- Master volume can be configured as pre or post line out
|
|
Engineered for professional PA installations, the A 4285B conservatively delivers 250W RMS power. Including three levels of input priority, bass and treble controls and phantom powering capability enable unparalleled flexibility for a wide scope of applications such as schools, shopping centres, workshops, mine sites and office buildings. |
 |
A4310 |
|
- 85% efficient class-D power performance.
- Low power consumption & heat generation.
- Compact 1RU case housing four individual amplifiers.
- Individual dedicated protection circuitry.
- Individual cooling systems for each channel.
- LED indicators for signal, peak, protection and power.
- Constant 100V floating output per channel (ie no reference to earth).
- Compatible with Altronics line monitoring equipment.
- 24V DC battery backup power.
- 240V AC operation.
- Remote control on/off switching function.
- In-built bandpass filter for 80Hz and 16KHz signals.
- Built-in short circuit, overload, high temperature protection.
- 2 year warranty
|
|
Excellent for multizone public address paging and background music systems! Engineered to meet the growing demands of venues such as RSL clubs, taverns, hotels, conference & function centres enabling individual program sources to play to different rooms |
 |
A4312 |
|
- 85% efficient class-D power performance.
- Low power consumption & heat generation.
- Compact 1RU case housing two individual amplifiers.
- Individual dedicated protection circuitry.
- Individual cooling systems for each channel.
- LED indicators for signal, peak, protection and power.
- Constant 100V floating output per channel (ie no reference to earth).
- Compatible with Altronics line monitoring equipment.
- 24V DC battery backup power (per channel).
- 240V AC operation.
- Remote control on/off switching function.
- In-built bandpass filter for 80Hz and 16KHz signals.
- Built-in short circuit, overload, high temperature protection.
- 2 year warranty
|
|
Excellent for multizone public address paging and background music systems! Engineered to meet the growing demands of venues such as RSL clubs, taverns, hotels, conference & function centres enabling individual program sources to play to different rooms |
 |
A4314 |
|
- 85% efficient class-D power performance.
- Low power consumption & heat generation.
- Compact 1RU case housing four individual amplifiers.
- Individual dedicated protection circuitry.
- Individual cooling systems for each channel.
- LED indicators for signal, peak, protection and power.
- Constant 100V floating output per channel (ie no reference to earth).
- Compatible with Altronics line monitoring equipment.
- 24V DC battery backup power (per channel).
- 240V AC operation.
- In-built bandpass filter for 80Hz and 16KHz signals.
- Built-in short circuit, overload, high temperature protection.
- 2 year warranty
|
|
Excellent for multizone public address paging and background music systems! Engineered to meet the growing demands of venues such as RSL clubs, taverns, hotels, conference & function centres enabling individual program sources to play to different rooms |
 |
A4316A |
|
- 85% efficient class-D power performance
- Low power consumption & heat generation
- Compact 1RU case housing two or four individual amplifiers
- Individual dedicated protection circuitry
- Individual cooling systems for each channel
- XLR cascade output (per channel)
- LED indicators for signal, peak, protection and power
- Constant 100V output per channel for PA system use
- 240V AC operation
- In-built bandpass filter for 80Hz and 16KHz signals
- Built-in short circuit, overload, high temperature protection
- 2 year warranty
|
|
This compact two channel Class-H design amplifier provides independent power amplifiers built into a single 1RU 19" rack mount chassis. It is ideal for use in environments where individual program sources are required in different building zones. Ideal for use in hotels, function centres, shopping malls and commercial offices. |
 |
A4320 |
|
- 5 inputs
- 4 output zones
- 70V or 100V output
- 4Ω or 8Ω output
- 24V DC operation
- Over temperature, over current and short circuit protection
- LED VU meter
- 2 year warranty
- Telephone paging input
- Chime and siren
|
|
An economical solution for smaller installations including offices, workshops, smaller shopping arcades, schools etc. |
 |
A4322 |
|
- 5 inputs
- 4 output zones
- 70V or 100V output
- 4Ω or 8Ω output
- 24V DC operation
- Over temperature, over current and short circuit protection
- LED VU meter
- 2 year warranty
- Telephone paging input
- Chime and siren
|
|
An economical solution for smaller installations including offices, workshops, smaller shopping arcades, schools etc. |
 |
A4324 |
|
- 5 inputs
- 4 output zones
- 70V or 100V output
- 4Ω or 8Ω output
- 24V DC operation
- Over temperature, over current and short circuit protection
- LED VU meter
- 2 year warranty
- Telephone paging input
- Chime and siren
|
|
An economical solution for smaller installations including offices, workshops, smaller shopping arcades, schools etc. |
 |
A4330 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 20W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A4332 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 40W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A4336 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 80W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A4344A |
|
- Digital AM/FM RDS tuner with 24 presets 18 x FM and 6 x AM
- USB File player with Autoplay and Autosearch functions
|
|
A plug-in AM/FM tuner module to suit all JDM public address amplifiers. |
 |
A4352 |
|
|
|
The optional A 4352 control PCB and A 4353 paging console allows remote paging to the 120, 240 and 480W JDM public address amplifiers. |
 |
A4353 |
|
|
|
The optional A 4352 control PCB and A 4353 paging console allows remote paging to the 120, 240 and 480W JDM public address amplifiers. |
 |
A4370 |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 70V, 100V and 4-16Ω outputs
- 240V AC or 24V DC operation
- 24V DC @ 1 Amp output for external devices
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
This range of booster amplifiers are ideal for installations requiring high power zone amplifiers. Simply choose a power rating according to the wattage required for each zone. |
 |
A4370A |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 70V, 100V and 4-16Ω outputs
- 240V AC or 24V DC operation
- 24V DC @ 1 Amp output for external devices
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
This range of booster amplifiers are ideal for installations requiring high power zone amplifiers. Simply choose a power rating according to the wattage required for each zone. |
 |
A4372 |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V outputs
- 240V AC or 24V DC operation
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
Consists of 2 x 125 Watt amplifiers in a single chassis. Ideal for multi-zone 100V PA requirements. Manufactured in Australia to stringent engineering criteria, the Phase 5 amplifier series exhibit quite remarkable performance and outstanding reliability. |
 |
A4373 |
|
- Maximum volume setting
- Minimum volume setting
- Australian designed and assembled
|
|
When fitted and used in conjunction with A 2280B wallplate to provide remote volume level adjustment. Ideal for situations where the amplifier is located in a remote rack. Plugs into the amplifier internally on the main board. |
 |
A4376 |
|
|
|
1 Pair of bolt on rack ears to allow installation of amplifiers into a 19" rack system. Designed to fit the following Redback models:
A 4375, A 4385, A 4375A, A 4385A, A 4377, A 4387, A 4210, A 4212. |
 |
A4377A |
|
- 3 Balanced microphone inputs / 3 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
This 125 Watt 4 channel mixer amplifier is specifically designed for applications requiring up to three microphone inputs, without compromising output power and overall performance. The amplifier feature three inputs which can be configured for either microphone or line level operation. |
 |
A4379 |
|
- 6 Balanced microphone inputs / 6 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
Designed for applications requiring up to six microphone inputs, without compromising output power and overall performance. Each model features inputs which can be configured for either microphone or line level operation. |
 |
A4380A |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 70V, 100V and 4-16Ω outputs
- 240V AC or 24V DC operation
- 24V DC @ 1 Amp output for external devices
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
This range of booster amplifiers are ideal for installations requiring high power zone amplifiers. Simply choose a power rating according to the wattage required for each zone. |
 |
A4387A |
|
- 3 Balanced microphone inputs / 3 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
This 250 Watt 4 channel mixer amplifier is specifically designed for applications requiring up to three microphone inputs, without compromising output power and overall performance. The amplifier feature three inputs which can be configured for either microphone or line level operation. |
 |
A4389 |
|
- 6 Balanced microphone inputs / 6 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
Designed for applications requiring up to six microphone inputs, without compromising output power and overall performance. Each model features inputs which can be configured for either microphone or line level operation. |
 |
A4390A |
|
- Multi-stage thermally cued fan cooling
- Input signal presence indicator
- Output peak limited
- 2U 19" rack mount (ears included)
- 3 pin XLR input, 3 pin XLR loop out
- Level control rear mounted
- 100V, 70V and 4 - 16Ω outputs
- Thermal and overload protection
- 240V AC, or 24V DC operation
- 300mA 24V battery trickle charge
|
|
This booster is ideal for installations requiring a high power zone amplifier. Ideal for use in shopping centres, pedestrian precincts, public transport facilities and convention centres. |
 |
A4395A |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 70V, 100V and 4-16Ω outputs
- 240V AC or 24V DC operation
- 24V DC @ 1 Amp output for external devices
- 300mA battery trickle charge
- Adjustable input level sensitivities
- Bass and Treble controls
- Phantom power on microphone input (XLR Input 1)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
The Redback A 4395 is a 500 Watt Mixer amplifier for installations requiring a high power zone amplifier. Ideally suited for use in shopping centres, pedestrian precincts, public transport facilities and convention centres. |
 |
A4411 |
|
- 2 microphone inputs
- Phantom power on MIc inputs (15V DC)
- 2 line inputs
- Separate tone controls for line and microphones
- Stereo outputs
- 1RU 19” rack mount case
- Master volume on rear panel
- Adjustable line muting
- Front panel mount microphone and line input
- Subwoofer output
- LED VU meter
- VOX active indicator
- Signal Present indicator
- 24V DC input
- 24V DC battery back up terminals
- 10 Year Warranty
- Australian designed & assembled
|
|
This 4 Channel Stereo Mixer has been designed to meet the growing demands of PA systems utilising high power stereo amplifiers, it features 2 balanced microphone and 2 auxiliary inputs. Perfect for aerobics use, bars, bistros, sporting clubs. |
 |
A4414 NEW
|
|
- Balanced input and outputs
- 3 pin XLR connections
- Mic or line level operation for individual input/outputs
- Loop output for connection to multiple distributors
- Compact half rack 1RU cabinet
- 24V DC operation
- Australian designed and manufactured
|
|
This compact half rack distributor comprises of a single 3 pin balanced XLR input to four 3 pin balanced XLR outputs. Great for splitting a single audio source out to multiple zones without interference between channels. |
 |
A4420C NEW
|
|
- 6 microphone and 2 line inputs
- All mic inputs are 3 pin XLR balanced
- Line inputs via twin RCA sockets
- Separate bass and treble tone controls
- Individual input and master volume controls
- Optional VOX muting of line inputs
- Optional phantom power for each mic input
- Microphone bass cut internally selectable
- Mic inputs routed via tone controls or bypassed
- 24VDC input
|
|
This 8 channel mixer incorporates a variety of practical features ensuring suitability for a wide scope of PA and sound reinforcement applications. |
 |
A4422 |
|
- To mount any of the Redback half rack products into a 19" wide racking system, the H 4990 bracket is required. If a single product is mounted into the H 4990, then a metal (H 4992) or plastic (H 4993) infill panel can be fitted for a neater finish.
|
|
The Redback® A 4422 4 channel mixer has been designed to meet the requirements of professional public address installations. It is ideally suited for use in shopping centres, gymnasiums, places of worship, court rooms etc. |
 |
A4424 NEW
|
|
- Six mic / line input channels.
- Two outputs via XLR/RCA 1V balanced.
- Level, bass and treble control on all inputs.
- Adjustable input sensitivity.
- Phantom power selection on each input.
- Route signals to each output or both outputs.
- Includes power supply
- 1RU 19” rack mount case.
- Australian designed & assembled
|
|
New to the Redback mixer stable, this model incorporates six inputs which can be routed to 1 of 2 outputs or both as the installation requires. Inputs can be configured for either RCA line level signals or 3 pin XLR balanced mic signals. |
 |
A4427 |
|
- Eight input channels
- Micro SD card message player for audio announcements
- Individual level, bass and treble control on all inputs
- Six levels of VOX priority
- Adjustable VOX sensitivity
- 3.5mm music input
- Adjustable input sensitivity on line inputs
- 24V DC battery back up terminals
- In built Alert/Evac/Chime functionality
- 24V DC output
- MP3 active indicator
- LED VU meter
- 10 Year Warranty
- Australian Designed and Manufactured
|
|
This unique Redback PA mixer features four input channels which are user selectable for either balanced mic, line or auxiliary use. In addition it incorporates a four channel SD card based message player making it an excellent choice for retail, supermarkets, hardware stores and more. |
 |
A4432 |
|
- Four Mic/ Line Input channels (Inputs 1-4)
- Four switched RCA AUX Input channels
- Remote AUX source selection, volume and Local input source volume control via optional A 4433 and A 4931 wall plates
- PTT Input and 24V PTT output (limited to 120mA) on inputs 1-4
- Micro SD card based Alert/Evac/Chime/Voice-over module (In built)
- Individual level, bass and treble control on all inputs
- 3.5mm music input overrides AUX 4
- Three levels of priority
- Adjustable Vox sensitivity on inputs 1-4
- Adjustable input sensitivity 1V/100mV on inputs 1-4 and Aux inputs 1-4
- Phantom Power on inputs 1-4
- Tape out (Dual RCA)
- Balanced Output (XLR male)
- Five sets of closing contacts for message triggering (Alert/Evac/Ch1/Ch2/Cancel)
- 24V DC switched output (Limited to 120mA)
- MP3 active indicator
- Signal Present indicator
- LED VU Meter
- 24V DC operation (Plugpack Supplied)
- 24V DC battery back up terminals
|
|
Designed in conjunction with pro-sound contractors, the A 4432 is a stand alone mixer which provides a flexible way to bring multiple audio sources together. It combines many of the best features from our popular mixer and signal processing range into one compact unit. |
 |
A4433 |
|
- Connects to A4432 mixer and A4931/32 local input
- Provides input selection options for four sources.
- Local volume level control.
- Selected source level control.
- Fits standard electrical wall box.
- Easy connection to A4432 via Cat5e/6 UTP data cabling.
- Powered over ethernet.
- Australian designed & assembled
|
|
A touchscreen control wallplate to suit the A 4432 Redback mixer. Allows quick and easy source selection, muting, level control for programming, plus local input level control (when used with A 4931/ A 4932). |
 |
A4435A |
|
- Four input channels
- SD card message player for audio announcements
- Individual level, bass and treble control on all inputs
- 3.5mm music input
- Adjustable input sensitivity on mic or line
- 24V DC battery back up terminals
- Four sets of closing contacts for message triggering
- 24V DC switched output
- Message active indicators
- Adjustable Vox sensitivity
|
|
This unique mixer features four input channels which are user selectable for either balanced mic, line or auxiliary use. It incorporates a four channel SD card based message player making it an excellent choice for retail, supermarkets and hardware stores. |
 |
A4450 |
|
- 4 mic/line inputs to 4 zones
- Operates as a matrix mixer or source switcher
- Touchscreen & iOS/Android app control
- RS-485 control via rear panel serial adapter connection
- Adjustable aux level 100mV/1V
- Adjustable balanced mic/line level 3mV/0.7V
- LCD for easy selection of sources to zones
- System cabling via Cat5e UTP.
- Zone and input custom labelling
- Adjustable volume for each input to output selection
- Master & zone source selection wallplates
- 24V DC operation
|
|
This Redback 4x4 audio source matrix system is feature packed yet simple to set up and use it features 4 inputs, selectable to up to 4 zones making it ideally suited to gyms, cafes, restaurants, small clubs and function centres. |
 |
A4460 |
|
- 4 in, 8 out stereo
- Touchscreen & iOS/Android app control
- Four external MP3 triggers
- Six wallplate activated triggers (master only)
- Remote wallplate control
- Global function to send to all zones
- System cabling via Cat5e UTP.
- Suits all size power amps
- Local Bluetooth inputs
- Master plate can control & set up all zones
- 24V DC operation
|
|
Designed to distribute 4 stereo audio input sources to 8 stereo output zones, this system is ideal for use in function centres, hotels, meeting rooms and domestic homes etc. It sends audio sources from one room to another with total ease. |
 |
A4461 |
|
- Simple touchscreen control selection of zone inputs and level control.
- Changes in selections are reflected on the relevant zone wall plates & main Redback units.
- Adjust custom labelling of zones and inputs on screen.
- Choose button colour theme.
- Fits standard double gang electrical wall box with mounting plate included.
- All glass front bezel for a stylish finish for any room.
- Adjustable screen sleep mode.
- Connects via economical Cat5e UTP cabling.
|
|
These 7" touchscreen control wall plates allow for remote source selection and level control in Redback source control systems (currently compatible with A4450, A4460 and A4650 systems). |
 |
A4462 |
|
- Simple touchscreen control selection of zone inputs and level control.
- Changes in selections are reflected on the relevant master wall plates & main Redback units.
- Fits standard single gang electrical wall box with mounting plate included.
- All glass front bezel for a stylish finish for any room.
- Adjustable screen sleep mode.
- Connects via economical Cat5e UTP cabling.
|
|
This 4.3" touchscreen control wall plate allows for remote source selection and level control in Redback source control systems (currently compatible with A4450, A4460 and A4650 systems). |
 |
A4463 NEW
|
|
- Simple touchscreen control selection of zone inputs and level control.
- Changes in selections are reflected on the relevant zone wall plates & main Redback units.
- Adjust custom labelling of zones and inputs on screen.
- Choose button colour theme.
- Fits standard double gang electrical wall box with mounting plate included.
- All glass front bezel for a stylish finish for any room.
- Adjustable screen sleep mode.
- Connects via economical Cat5e UTP cabling.
|
|
These 7" touchscreen control wall plates allow for remote source selection and level control in Redback source control systems (currently compatible with A4450, A4460 and A4650 systems). |
 |
A4464 NEW
|
|
- Simple touchscreen control selection of zone inputs and level control.
- Changes in selections are reflected on the relevant master wall plates & main Redback units.
- Fits standard single gang electrical wall box with mounting plate included.
- All glass front bezel for a stylish finish for any room.
- Adjustable screen sleep mode.
- Connects via economical Cat5e UTP cabling.
|
|
This 4.3" touchscreen control wall plate allows for remote source selection and level control in Redback source control systems (currently compatible with A4450, A4460 and A4650 systems). |
 |
A4469 |
|
-
 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 45 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
 Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
The A4469 zone relay unit may be installed remotely and has been designed to switch either low level inputs or amplifier outputs and interfaces the A4660 paging console with existing PA systems. |
 |
A4476 |
|
- Remote preset selection
- Cat5e connection
- LCD indicates presets available
|
|
The A4476 wallplate is used to provide local access to presets programmed into the A4480B. |
 |
A4480B |
|
- 8 Stereo RCA line inputs (internally mono mixed).
- 2 Microphone XLR inputs with phantom power option.
- Adjustable line input sensitivity 0.3/0.7V.
- Individual bass, treble and volume controls of all line inputs.
- 8 Balanced 3 pin XLR line outputs.
- Individual volume controls of all 8 outputs.
- Alert/evacuation/pre chime tone generator included (alert/evac tones comply to AS1670.4) .
- Emergency balanced input with selectable phantom power and input sensitivity.
- Programmable labelling of input sources and output zones via USB keyboard.
- Programme isolate function.
- Four programmable presets.
- Tampering lockout feature.
- Power fail trigger.
- 240V AC or 24V DC operation.
- 19” Rack Mount (2 unit).
|
|
Designed to meet the demands of todays complex audio installations. This very versatile, cost effective, PA/BGM control system is suitable for clubs, pubs, gyms etc. It is ideally suited as a central controller for all audio inputs and outputs in a multiz |
 |
A4487 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 45 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
Provides a microphone or line level output which can be connected directly to the input of an amplifier. Connection between the A 4660 paging console and this unit is via a Cat5e cable which carries power and the balanced audio output from the microphone. |
 |
A4489A |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 45 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
The A4489A zone relay unit may be installed remotely and has been designed to switch either low level inputs or amplifier outputs and interfaces the A4660 paging console with existing PA systems. Suits for line level or 100V line zone switching. |
 |
A4495 |
|
- Remote selection of input audio source
- Volume control of zone input
- Volume control of local zone input
- Mute function
- Zone Lockout
- Personal Identification Number (PIN) Menu Lockout Function
- 2 stage wall plate functionality Lockout
- Provision for input of local microphone or line level audio via A4931 or A4931V wall plates
- Cat5e connection to A4480B
- Powered from the A4480B
|
|
The A4495 wall plate allows remote selection of the A4480B zone input audio source and volume level (1 plate required per zone). |
 |
A4496 NEW
|
|
- Remote selection of input audio source
- Volume control of zone input
- Volume control of local input
- Mute function
- Zone Lockout
- Personal Identification Number (PIN) Menu Lockout Function
- 2 stage wall plate functionality Lockout
- Provision for input of local microphone or line level audio via A4931 or A4931V wall plates
- Cat5e connection to A4480B
- Powered from the A4480B
|
|
The A4496 wall plate allows remote selection of the A4480B zone input audio source and volume level (1 plate required per zone). |
 |
A4500C |
|
- MP3 bell, prebell & music timing outputs.
- Emergency tones conform to AS 1670.4.
- Random play for prebell and music.
- Easy PC based timing event setup.
- Remote triggering of alert, evac and bell.
- Provision for connection to A4660 touchscreen paging console.
- Switched 24VDC out for bell, alert/evac.
- Pluggable screw terminal connections.
- Auxiliary level output.
- Battery backup of current time.
- 24V DC operation.
- Standard 1U 19” rack mount case.
- Suitable for any amp with an aux input.
- 10 Year Warranty
- Australian Designed and Manufactured
- Includes Power Supply
|
|
A weekly timer and evacuation controller all housed in a convenient 1RU rack mount chassis. A total of 200 “event” switching times are available through the timing functions. Each event can be set to turn on from 1 sec up to 24 hours. |
 |
A4505C |
|
- MP3 for bell, prebell & music timing output.
- Emergency tones conform to AS 1670.4
- Random play of MP3 for prebell and music triggers.
- Easy PC based timing event setup
- Local & remote triggering of lockdown, fire and bell.
- Provision for connection to A4660 touchscreen paging console.
- MP3 voice over message (available in the lockdown and the fire cycle)
- Switched 24VDC outputs
- Pluggable screw terminal connections
- Auxiliary level output
- Battery backup of current time
- 24V DC operation
- 1RU 19” rack case
- Suitable for any amplifier with aux input
- 10 Year Warranty
- Australian Designed and Manufactured
|
|
A timed audio announcement, lockdown and fire alarm controller all housed in a convenient 1RU rack mount chassis. For scheduled announcements a total of 200 “event” switching times are available through the timing functions. |
 |
A4506 |
|
- With mains power failure the connected batteries are relay switched to the load via two 50A terminals. A sensing circuit disconnects the load when the minimum permissible discharge voltage is reached, thus preventing permanent battery damage. This charger is specifically designed for use on sealed lead acid batteries, gel technology batteries and standard vented lead acid batteries.
|
|
Ideal for PA systems & other applications requiring battery backup. This all new model incorporates a highly efficient, intelligent, multi stage switchmode battery charger ensuring optimum battery charging and performance. |
 |
A4510B NEW
|
|
- MP3 audio format for Bell, Prebell and Music timing outputs
- Random play of audio files for Prebell and Music activations
- Easy Windows based software timing event setup
- Daylight savings mode
- Local push button operation of Bell
- Switched 24VDC output for Bell, Prebell, Music and relay only (No audio) output activations
- Bell trigger for remote activation of the bell
- Pluggable screw terminal connections
- Auxiliary level output
- Battery backup of current time
- 24V DC operation
- Standard 2U 19” rack mount case
- Suitable for any amplifier with an auxiliary input
- 10 Year Warranty
- Australian Designed and Manufactured
|
|
The A 4510B is an incredibly versatile, and easily programmed yearly timer housed in a convenient 2RU rack or desk mount chassis. The unit can be programmed for virtually limitless* timing events for each day of the year. |
 |
A4512 |
|
- Mains failure battery backup operation: With mains power failure the connected batteries are relay switched to the load via two 50A terminals. A sensing circuit disconnects the load when the minimum permissible discharge voltage is reached, thus preventing permanent battery damage. This charger is specifically designed for use on sealed lead acid batteries, gel technology batteries and standard vented lead acid batteries.
|
|
Ideal for PA systems & other applications requiring battery backup. This all new model incorporates a highly efficient, intelligent, multi stage switchmode battery charger ensuring optimum battery charging and performance. |
 |
A4565A |
|
- Tones conform to AS 1670.4
- Standard 1U 19” rack mount case
- Interfaces with Fire Indicator Boards
- Remote operation of Alert, Evac, Chime, Fire Test, Fire Alarm & Cancel tones
- MP3 based tone playback (with backup hard coded Alert, Evac and Bell tones)
- 24V DC operation
- Auto/Manual/Isolate keyswitch
- Key switch to 003 standard
- Local operation of Alert, Evac and PA
- MP3 based Voice Over messages for Alert and Evac cycles
- Microphone socket for PA use
- Provision for BGM (back ground music)
- Provision for Auxiliary input with front volume control
- Bell chime facility
- Switched 24V DC output for override relays on volume controls
- Switched 24V DC output for strobe operation for Alert mode
- Switched 24V DC output for strobe operation for Evac mode
- Switched 24VDC output for bell mode
- On-board timer for automatic Alert to Evac switchover, adjustable from 30secs to 7.5min in 30 second increments
- Externally operated inputs are activated by switching to ground
- Auxiliary level output
- Suitable for any amplifier with an auxiliary input
- 10 Year Warranty
- Australian Designed and Manufactured
|
|
This easy to operate building alert & evacuation controller controller is designed around industry standard building requirements. When connected to a paging system amplifier, occupants can be alerted and/or evacuated in the event of an emergency eg: fire, gas leak, bomb scare, earthquake. |
 |
A4566 |
|
- Designed & manufactured in Australia.
- Since 1976 Redback public address products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
A simple in-line connection box fitted with a line monitoring capacitor. Since many 100V speakers do not have 22μF capacitors fitted, this box allows you to easily add it into the circuit for connection to a line monitoring system. |
 |
A4567C |
|
- This unit is designed for “loop in loop out” serial wiring to loudspeakers with a 100kΩ terminating resistor at the end of the line. Star wiring or tee offs are prohibited. Each loudspeaker requires a series connected 22µf bipolar capacitor for correct operation. A delay of 10 seconds is provided before registering a fault to minimise false alarms.
|
|
Specifically designed to monitor the condition of 100V line speaker systems in emergency paging and fire evacuation installations. Many large commercial installations have speaker circuits in excess of 250W. |
 |
A4568 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
Designed to interface the A4567 Line monitoring unit with a fire indicator board. The addition of the A4568 enables you to monitor the status of each individual zone. |
 |
A4573 |
|
- Designed & manufactured in Australia.
- Since 1976 Redback public address products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
Optional Plugin Board to suit the Phase 4 range of Redback Amplifiers. It generates pre chime, bell, alert and evacuation tones. The alert tone can function continuously, or switch to evac tone after a preset time delay (adjustable 30 seconds to 4.5 minu |
 |
A4574A NEW
|
|
- Level controls for alert/evac, bell and voice over
- Front panel alert/evac/bell and cancel switches
- All tones MP3 based
- Alert/Evac Emergency tones can be configured for momentary or continuous operation
- 1U half rack cabinet
- Alert and Evac Tones conform to AS 1670.4 (Library included on Micro SD card)
- Compatible with fire indicator boards & break glass alarms
- Remote operation of alert , evac, bell tones & cancel.
- Local operation of alert, evac and bell
- MP3 based Alert and Evacuation Voice over message facility
- Bell chime facility
- Switched 24V DC outputs for override relays or strobes (outputs limited to 120mA)
- On-board timer for remote alert activation adjustable from 30secs to 7.5min in 30 second increments.
- Switches from alert to evac after preset time.
- Auxiliary level output
- 10 year warranty
- Australian designed and manufactured
|
|
This unit has provision for playback of Alert, Evacuation and chime tones as well as an alert and/or emergency message. When connected to a paging system amplifier, building occupants can be alerted and/or evacuated in the event of an emergency e.g.: fire, gas leak, bomb scare, earthquake. |
 |
A4576 |
|
- Designed & manufactured in Australia.
- Since 1976 Redback public address products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
Designed for both 12V and 24V operation, this wallplate will sound a buzzer and illuminate an LED indicator when activated. A cancel button allows buzzer to be switched off, whilst the LED remains on. Connects with standard figure 8 cable and operates onc |
 |
A4577 |
|
- Six monitored Inputs/triggers.
- 12 to 30V DC powered.
- Audible alert by buzzer.
- Visual alert by LED (individual LED per trigger).
- LEDs stay illuminated until trigger is deactivated.
- Cancel switch to stop audible alert.
- Pluggable terminal block for Triggers and DC in.
|
|
Designed to operate on 12 to 30VDC. This six input wall plate will sound a buzzer and
illuminate a specific LED when an input is activated/triggered by a closing contact. A
Cancel button allows the buzzer to be switched off whilst the LED indicator rema |
 |
A4578 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
Allows the A4565A alert/evac unit to be activated remotely. Featuring alert, evacuation and cancel buttons with protective "flip up" covers to prevent accidental operation. |
 |
A4579 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
Designed for use with the A 4500B Timer and A 4505B Lockdown Timer |
 |
A4580 |
|
- Amplifier 100V level or low level balanced line switching
- Selectable pre and post announcement chimes via A4660 (Internal or MP3/SD card based)
- Selectable BGM for each zone
- Accepts up to 8 paging consoles
- Expandable up to 32 zones with additional A 4580
- Paging consoles connect via Cat 5 cable
- Paging consoles can be up to 200m from control box
- Operates from 24V DC plugpack (supplied)
- All inputs/outputs via pluggable terminals
- Suitable for 1 or 2 amplifier systems
- Evac "All Call" input for emergency tones or telephone paging.
- Maximum 500W power handling over 16 zones
- 1U 19” rack mount
|
|
This unit is a very versatile cost effective public address/background music control system which provides audio to up to 16 zones. Backgound music which can be selected to play through any zone is muted when general paging occurs or when an evacuation input overrides the system. |
 |
A4581 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
Allows the A4565A & A4500B alert/evac units to be activated remotely. Featuring alert, evacuation and cancel buttons with protective "flip up" covers to prevent accidental operation. |
 |
A4581V |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
The A4581V wall plate allows remote triggering of the Alert, Evacuation and Bell tones and the cancel function of the A4565A Alert/Evacuation Controller. |
 |
A4582 |
|
- 2U 19" rack mount
- Monitors up to 10 100V line amplifiers
- Analogue VU output level display
- No power required
- Built in monitor speaker
- Speaker volume control
- Minimal circuitry for low noise
|
|
A handy aid to test and adjust 100V line PA amplifier output levels. Capable of monitoring 10 individual amplifiers (electrically isolated from each other to prevent cross talk). Audible and visual monitoring is available from the built in speaker and VU |
 |
A4595A |
|
- 1U 19” rack mount
- Interfaces with A 4565 for a complete fire/evac & lockdown system
- 24V DC operation (plugpack included)
- Period bell, standby, lock down and all clear controls with remote contacts
- Connects to lockdown wallplate and/or paging console via Cat5e UTP cabling
- MP3 SD card tone & audio announcement playback
- RCA audio output
- Up to 4 paging consoles and 16 remote wallplates per system
- Flip up switch covers to prevent accidental triggering
- Adjustable rear mounted level control
- Switched 24V outputs for all conditions (all clear, standby, lockdown, bell, pre-bell, emergency & common contacts).
|
|
This lockdown controller complements the A 4565 Alert/Evac controller and is primarily aimed at schools which require a lockdown warning facility. |
 |
A4597 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
This remote wallplate interfaces with a building fire evacuation control board to offer simple fire alarm test triggering. |
 |
A4598 |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
The remote wall plates provide the same functionality as the buttons on the front of the A 4595A. All switches have safety covers to prevent accidental triggering. If a tone is triggered by the main unit or a paging console the corresponding switch on the wall plate will illuminate. |
 |
A4598V |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
- Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
The remote wall plates provide the same functionality as the buttons on the front of the A4595A. |
 |
A4599 |
|
- Allows remote activation of the A4505 Controller.
- Connection is made via Cat5e cable up to a maximum range of 300m.
- Protective “flip up” covers. to prevent accidental operation.
- Dual Facia covers included.
- Fits standard electrical wall boxes.
|
|
Redback WallPlate allows the A 4505 Lockdown Timer to be controlled remotely. Featuring Lockdown, Fire, Chime and Cancel buttons, the plate can be located up to 100m away from the main unit. |
 |
A4599V |
|
- Allows remote activation of the A4505 Controller.
- Connection is made via Cat5e cable up to a maximum range of 300m.
- Protective “flip up” covers. to prevent accidental operation.
- Dual Facia covers included.
- Fits standard electrical wall boxes.
|
|
Redback WallPlate allows the A 4505 Lockdown Timer to be controlled remotely. Featuring Lockdown, Fire, Chime and Cancel buttons, the plate can be located up to 100m away from the main unit. |
 |
A4658 NEW
|
|
- Simple in-line connection
- Provides additional power for long cable runs
- Aluminium case
- 24V DC power input (power supply included)
- Australian designed and manufactured
|
|
Designed to provide external power injection to the new A 4660 Redback Paging Console. |
 |
A4660 NEW
|
|
- Standard Features:
- Touch control paging with pre and post announcement chime options.
- Adjustable microphone automatic gain control (AGC).
- High quality electret microphone with high ambient noise control and feedback rejection.
- Adjustable backlight brightness and dimmed brightness levels with selectable timeout period.
- All glass front bezel for a stylish finish for any room.
- Connects via economical Cat5e UTP cabling.
|
|
This paging console is designed to provide general paging to zones when connected to the Redback A 4450, A 4460 or A 4650 systems. It provides a visual indication of the status of all audio sources and zones within the system at a glance, sharing a common screen with the master wallplates available for use with these systems. |
 |
A4661 NEW
|
|
- Standard Features:
- Touch control paging with pre and post announcement chime options.
- Adjustable microphone automatic gain control (AGC).
- High quality electret microphone with high ambient noise control and feedback rejection.
- Adjustable backlight brightness and dimmed brightness levels with selectable timeout period.
- All glass front bezel for a stylish finish for any room.
- Connects via economical Cat5e UTP cabling.
|
|
This paging console is designed to provide general paging to zones when connected to the Redback A 4450, A 4460 or A 4650 systems. It provides a visual indication of the status of all audio sources and zones within the system at a glance, sharing a common screen with the master wallplates available for use with these systems. |
