|
Description |
Downloads |
Specs |
Ordering |
|
 |
A2514 |
|
|
|
Unbalanced 10K Ohm 2 x RCA to balanced 600 Ohm 3 pin male XLR with level control. -10dB max signal gain. |
 |
A1116 |
|
|
|
This 2x25W RMS amplifier module with Bluetooth receiver sticks to your speaker magnet and connects to a pair of in-ceiling/in-wall speakers. Easy to install and works with Bluetooth enabled devices such as smartphones, tablets and laptops. Includes 15V power supply. |
 |
C0377 |
|
- Polar Pattern: Cardioid unidirectional
- Impedance: 600 Ohm
- Frequency Response: 80Hz-12kHz
- Sensitivity: -70dB ±3dB
- Housing: Powder coated zinc diecast
- Cable: 2m Twin shield
- Weight: 960g
|
|
This desk microphone has a tapered low frequency response for articulate speech reproduction and enhanced clarity. Fitted with a 2 metre lead and terminated with either a 3 pin XLR, 5 pin XLR or 5 pin DIN connector. The 5 pin XLR and 5 pin DIN type conn |
 |
A4860 |
|
- Class-D 2 x 50W amplifier
- Bluetooth 4.2 wireless streaming
- Stereo RCA & 3.5mm jack inputs
- Optical input with high performance DAC
- Automatic signal switching with priority for Bluetooth audio source
- 240V AC operation
|
|
This compact stereo class-D amplifier features Bluetooth 4.2 streaming with in-built optical input for digital audio sources. The amplifier is also fitted with 3.5mm stereo jack and stereo RCA inputs for connection to external audio sources. Bluetooth takes priority over all other inputs, providing easy wireless streaming when you need it. The 2 x |
 |
A4201 |
|
- SPECIFCATIONS:
- Power Output: 50 Watts RMS x 2 into 8 ohm
- Total Harmonic Distortion: <0.01% @30W; <5.0% @50W
- Minimum Speaker Impedance: 6 ohm
- Signal-to-Noise Ratio: 103 dB, A weighted
- Input Impedance: 2k ohm ± 5%
- Frequency response: 20-20,000 Hz
- Channel Separation: 95 dB
- Efficiency: 85%
- Dynamic Range: >100 dB
- Electrical Requirement: 24V DC @ 5A centre pin positive
- Dimensions: 50H x 86W x 143D mm
- Weight: 455g
- BLUETOOTH SPECIFICATIONS:
- Bluetooth version: BT V5.0
- Analog input sensitivity: 1-2V RMS
- Bluetooth range: 30m (line of sight)
- Decoding: SBC, MP3, AAC
- Output: A2DP, AVRCP
|
|
A compact, sturdy 2x50W RMS class-D stereo amplifier with 3.5mm input on the front and RCA input on the back for easy connection. |
 |
A2513 |
|
|
|
Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control. +10dB max signal gain. Steps up input signal by factor of 16, ie 20mV in = 320mV out. |
 |
A4280 |
|
- Multi-stage thermally cued fan cooling
- 2U 19” rack mount (with optional A 4376)
- Tape record out terminals
- Provision for connection to Redback A4660 touchscreen paging console
- MP3 based Alert/Evac tones with MP3 voice over message for emergency tones (built in)
- 3 mic input and 4 auxiliary inputs
- Phantom powering available on all inputs
- Adjustable vox muting on inputs 1 & 2.
- Bass and treble tone controls
- Terminals for 100V line output
- 240V AC or 24V DC power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- Australian designed & assembled
|
|
Similar in functionality to the recently released A 4377/A4387 amplifiers with the addition of four 100V line output zones. |
 |
A4047 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 100W RMS respectively. |
 |
A4903A |
|
- Screw terminals for 100V input
- Microphone or line level balanced outputs (3 pin XLR)
- Line level unbalanced output (2 x RCA)
- Recessed volume control to prevent tampering
- Requires no power
- Minimal loading or signal loss
- Dimensions 133W x 45H x 55D mm.
|
|
This small adaptor receives a 100V signal from one amplifier and reduces the level down to either balanced mic level or auxiliary level to feed into the input of a second amplifier. |
 |
A2548 |
|
- Ultra compact design with USB PC interface
- Windows & Mac OSX compatible
- Powered via USB
- High/low/mid 3 band EQ
- Fader level control
- 48V phantom power button
- Mute buttons
- 3.5mm headphone output and mic input
- Channel -14dB to +40dB gain control
- Signal input and clip indicators
- -20dB pad switch
|
|
A perfect little mixer companion for your PC/laptop for home recording. Measuring only 124mm wide it takes up very little desk space whilst still offering features found on mixers twice the size - such as fader level control, three band EQ and effects. |
 |
A3043 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Microphone pre-amp gain: 40dB
- Min load: 4ohm
- Current draw: 2A max.
- Power: 12V dc
- Dimensions: 92.6L x 73.4W x 26.6H mm
- Weight: 160g
|
|
This compact amplifier is a great way to power a pair of speakers without the bulk of a full size hi-fi receiver. It provides 2x15W RMS output power - enough to power a pair of small ceiling or bookshelf speakers. |
 |
A4580 |
|
- Amplifier 100V level or low level balanced line switching
- Selectable pre and post announcement chimes via A4660 (Internal or MP3/SD card based)
- Selectable BGM for each zone
- Accepts up to 8 paging consoles
- Expandable up to 32 zones with additional A 4580
- Paging consoles connect via Cat 5 cable
- Paging consoles can be up to 200m from control box
- Operates from 24V DC plugpack (supplied)
- All inputs/outputs via pluggable terminals
- Suitable for 1 or 2 amplifier systems
- Evac "All Call" input for emergency tones or telephone paging.
- Maximum 500W power handling over 16 zones
- 1U 19” rack mount
|
|
This unit is a very versatile cost effective public address/background music control system which provides audio to up to 16 zones. Backgound music which can be selected to play through any zone is muted when general paging occurs or when an evacuation input overrides the system. |
 |
A1717 |
|
- Electrical
- Output line: Stereo RCA 500mV nominal
- Power supply: 24VDC
- MP3 sample rate: 44kHz
- SD card size: 256MB to 8GB
- Trigger activation: Closing contact
- Switched output: 12-30V DC out (supply voltage dependant)
- MP3 specification
- Length/size: Limited only by card size (16GB max)
- Bit rate: All standard MP3 rates (128kbps recommended)
- Sample rate: All standard MP3 rates (44.1kHz recommended)
- Channels: Stereo or mono
- Mechanical
- Dimensions: 105W x 81D x 25H mm
- Weight: ≈0.5kg
|
|
The A 1717 is an MP3 based message player, housed in a compact flange mount aluminium enclosure and offers playback of four MP3 tracks. 4 Message |
 |
C8884 |
|
- Multilevel high and mid frequency narrowband filters
- Advanced noise detection and control
- Tone key linked identity to reduce interference
- Operating frequencies 520 / 524 MHz
- RF signal presence indicator LEDs for channels A and B
- Range of up to 60m in ideal conditions open air
- 6.35mm unbalanced line mix output
- 3-pin balanced XLR mic output for channels A and B
- Screen shows parameters for both channels
- Plug pack included
- 4 x AA batteries included
|
|
For systems requiring the freedom of two independent wireless microphones at an economical price. The sturdy 1/2 rack mount cabinet is fitted with 2 channel fixed frequency wireless receiver. |
 |
A4480B |
|
- 8 Stereo RCA line inputs (internally mono mixed).
- 2 Microphone XLR inputs with phantom power option.
- Adjustable line input sensitivity 0.3/0.7V.
- Individual bass, treble and volume controls of all line inputs.
- 8 Balanced 3 pin XLR line outputs.
- Individual volume controls of all 8 outputs.
- Alert/evacuation/pre chime tone generator included (alert/evac tones comply to AS1670.4) .
- Emergency balanced input with selectable phantom power and input sensitivity.
- Programmable labelling of input sources and output zones via USB keyboard.
- Programme isolate function.
- Four programmable presets.
- Tampering lockout feature.
- Power fail trigger.
- 240V AC or 24V DC operation.
- 19” Rack Mount (2 unit).
|
|
Designed to meet the demands of todays complex audio installations. This very versatile, cost effective, PA/BGM control system is suitable for clubs, pubs, gyms etc. It is ideally suited as a central controller for all audio inputs and outputs in a multiz |
 |
A4861 |
|
- 200W into 4 ohms
- Stereo RCA input
- Speaker level input and outputs
- Adjustable phase and crossover frequency
- Volume level control
- 240V AC operation
|
|
A compact dedicated subwoofer amplifier providing up to 200W into 4 ohms. Ideally paired with the A 4860 and C 1065 ceiling subwoofer, but is also suitable for any passive subwoofer. Ideal for integration with commercial systems in fashion boutiques, shopping centres, gymnasiums etc. Front panel provides level control, phase adjustment and crossov |
 |
A4270 |
|
- Multi-stage thermally cued fan cooling
- 2U 19” rack mount (with optional A 4376)
- Tape record out terminals
- Provision for connection to Redback A4660 touchscreen paging console
- MP3 based Alert/Evac tones with MP3 voice over message for emergency tones (built in)
- 3 mic input and 4 auxiliary inputs
- Phantom powering available on all inputs
- Adjustable vox muting on inputs 1 & 2.
- Bass and treble tone controls
- Terminals for 100V line output
- 240V AC or 24V DC power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- Australian designed & assembled
|
|
Similar in functionality to the recently released A 4377/A4387 amplifiers with the addition of four 100V line output zones. |
 |
A2710 |
|
- Accepts USB stick, SD an CF memory FAT32 format up to 32Gb
- Supports MP3 folder hierarchy structure ie: will browse music inside folders on stick
- Compact size
- Line level volume adjustment
- Simple plug and play operation
- Box flange allows mounting to any surface
- Automatic playback looping
- Starts playback immediately once USB is plugged in
- If power is lost, playback will play from the start of the last played track.
|
|
Designed for BGM systems in commercial installations requiring audio playback from a USB memory stick. Alternatively it can be used to add MP3 playback to any domestic audio system. Simply connects to an amplifiers RCA input and provides typical CD player. |
 |
A2651 |
|
- All inputs top mounted for easy access
- Dual 6.35mm TRS outputs
- LED VU meters
- USB/SD card MP3 playback with transport controls
- Repeat and delay effects
- External effects send & return
- Phones/monitor output & level
- Selectable phantom power
- Gain, monitor, effect, pan, high, mid & low levels controls on all channels
- Record RCA output
- LCD readout for USB playback
|
|
This compact high performance desk mixer is ideal for live/stage sound mixing in small applications such as theatre, bands, function centres and venues. It offers added flexibility for audio playback with a USB and SD card input on the rear panel. Playba |
 |
A4905 |
|
- XLR Mic input
- RCA Aux input
- XLR balanced output.
- Phantom power to Mic Input (15V DC).
- Controls for AUX, MIC and master volume.
- DIP Switch selectable AUX input sensitivity.
- 24VDC operation via 2.1mm DC power jack.
|
|
This line pre-amp will accept either a microphone or auxiliary input and convert it to a balanced high level signal suitable for distribution up to 500M without interference with up to 3V of output level available. Volume controls are provided for both inputs plus a master volume control. The microphone is a balanced XLR input whilst the auxiliary |
 |
A4043 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 100W RMS respectively. |
 |
A4017 |
|
- To mount any of the Redback half rack products into a 19" wide racking system, the H 4990 bracket is required. If a single product is mounted into the H 4990, then a metal (H 4992) or plastic (H 4993) infill panel can be fitted for a neater finish.
|
|
Super compact with surprising performance specifications, intended for smaller PA system applications. Our engineering team based the design around a National TDA1519 monolithic IC achieving virtually "destruction proof" operation under quite severe misuse |
 |
A2517 |
|
|
|
Unbalanced stereo 2 x RCA to unbalanced stereo 2 x RCA. |
 |
P8167 |
|
- Overload protection
- Both IEC and Australian Sockets
- Rack ear mounting
- Power cord located at the rear
- High surge protection
- 240V a.c. 10A
|
|
The neat solution to supplying mains power to your mounted equipment. |
 |
A4336 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 80W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A2776C |
|
- Bluetooth compatible for wireless music streaming This AV receiver is equipped with Bluetooth functionality to let you enjoy easy wireless music playback from smartphones and other devices. Yamaha Compressed Music Enhancer is now optimised for Bluetooth audio transmission to ensure that your music will have vivid, lively sound quality even during wireless playback.
- 4K Ultra HD full support with 4K60p, HDCP2.2 This AV receiver completely supports with the latest HDMI standards. Thanks to transmission of 4K video at 60 frames per second pass-through, you can fully enjoy the high definition video quality of 4K without degradation. It also adheres to the HDCP2.2 copyright protection standard for 4K video transmission.
- HDMI with 3D and Audio Return Channel 3D means the receiver can handle 3D signal data. The Audio Return Channel function enables data to be sent and received via the same HDMI cable, so you can hear the sound from the TV via a single HDMI cable, with no need for an extra optical cable.
- Discrete amp configuration for high sound quality This AV receiver was designed with a strong focus on achieving exceptionally high sound clarity. It employs a discrete amp configuration and a low jitter PLL circuit, which contribute to its excellent audio performance.
- AV setup guide app makes system setup easier AV Setup Guide is an app that makes it much easier to perform receiver setup, and also assists you with cable connections between the AV receiver and source devices. It guides you through various settings such as speaker connections, TV and source device connections and power amp assignment. System illustrations and actual AV receiver images help you understand how to make the connections between devices, for much quicker system setup. It is available in multiple languages. Designed for iOS and Android tablet.
- SCENE for one-touch start Pressing a SCENE button powers on the AV Receiver and selects the input source and DSP mode. You can re-set the buttons for different sources by selecting a source and DSP mode, then pressing a SCENE button for more than three seconds.
- HDMI CEC for easy operation Another benefit of HDMI is the availability of CEC functionality. When the unit is connected to a CEC compatible TV, it will turn on and off together with the TV, and you can use the TV remote to control the volume. CEC also provides advanced functionality with other components. For example, you can use the receiver’s remote unit to control player functions like Skip and Stop. NOTE: All connected devices must be HDMI CEC compatible. Some CEC compatible TVs / players may not work.
- YPAO sound optimisation for automatic speaker setup YPAO analyses the room acoustics and adjusts various audio parameters for optimum sound in just a few minutes. It’s like having a professional installer calibrate your system.
- HD audio with CINEMA DSP Yamaha’s exclusive CINEMA DSP technology supports playback of HD Audio (Dolby TrueHD, DTS-HD Master Audio, etc.), providing natural and expansive sound imaging.
- Virtual CINEMA FRONT provides irtual 5-channel surround sound with high quality and resolution Even when it is impossible to install surround speakers behind the listening position, Virtual CINEMA DSP reproduces virtual 5-channel surround sound filled with realism, with only two front speakers. With Virtual CINEMA FRONT, you will enjoy virtual 5-channel surround sound with higher quality and resolution by installing surround speakers at the front. You get more flexibility to arrange your speakers inside the room, along with easy enjoyment of high quality surround sound.
- Extra Bass provides rich bass reproduction, even with small speakers Yamaha’ s exclusive low-range enhancement technology delivers richer bass than you expect from the speaker size while maintaining good localisation and sound balance even with compact front speakers. When a subwoofer is used, it improves the volume of the entire low range of the speaker system, not only the front speakers, but also enhancing the bass from the subwoofer. You'll enjoy video and music with sound that has exceptional power and presence.
- Compressed Music Enhancer When music is encoded into a digitally compressed format like MP3, the frequency response suffers. Yamaha’s Compressed Music Enhancer employs sophisticated digital signal processing using exclusive algorithms to restore what was lost, so the music always sounds the way it should.
- Subwoofer Trim for improved sound imaging The Subwoofer Trim control enhances the low frequencies by avoiding overlap with the front speaker output. This will result in a cleaner, more focused sound stage while providing a seamless frequency response. When subwoofer frequency overlap occurs in conventional systems, the overall sound is “pushed” toward the subwoofer. Subwoofer Trim takes care of this by separating the low subwoofer frequencies cleanly, thus stabilising the front stage while providing a well-balanced enhanced bass sound.
- ECO mode lowers power consumption by 20%* Yamaha’s new ECO mode reduces power consumption by about 20%. It can be set from the top of the GUI menu. NOTE: Compared to power consumption when ECO mode is off (Yamaha measurement).
- Selectable auto power standby Auto Power Standby lets you save energy by selecting to turn off the power after 20 minutes, 2, 4, 8 or 12 hours.
|
|
The all-new RX-V385 model is wireless-enabled, with streaming from Bluetooth devices at the touch of a button. Movie watchers are also catered for with 4K Ultra HD as well as HDMI 2.0, BT.2020 compatibility and HDCP 2.2, HDR video. 70W RMS per channel. Four HDMI inputs. AM/FM analog tuner. |
 |
A4157 |
|
- Output Power (Stereo 8Ω): 250W + 250W
- TA 1KHz THD≤1% (4Ω): 370W + 370W
- Bridge 8Ω: 740W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <740W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 9kg
- Gross Weight: 10kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4199 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Headphone output: 105mW RMS per channel
- Headphone distortion: 0.05%
- Min load: 4Ω
- Current draw: 9A max.
- Power: 12V DC
- Dimensions: 285W x 128D x 43Hmm
- Weight: 0.8kg
|
|
Ideal for small businesses or simple multi-zone home audio systems. Switch between up to 4 different audio sources - connect up to 8 speakers. Toslink digital audio input for TV audio. Great for background music use. Also fitted with 6.35mm microphone connection. |
 |
C8881B |
|
- Operating frequencies 520 / 524.30MHz
- 19” 1RU rack mount case
- Steel enclosure construction
- Removable aerials
- Individual 3 pin XLR outputs
- Mixed 6.35mm jack output (1m cable included)
- Front panel level controls
- Tone squelch circuit for noise reduction
- RF, AF & peak signal LEDs
- Range up to 50m in ideal conditions
|
|
For systems requiring the freedom of two independent wireless microphones at an economical price. The sturdy 19" rack mount cabinet is fitted with two fixed frequency wireless receivers. The miniaturised SMD construction and unique shielding technique, pl |
 |
A4155 |
|
- Output Power (Stereo 8Ω): 150W + 150W
- TA 1KHz THD≤1% (4Ω): 220W + 220W
- Bridge 8Ω: 440W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <440W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 8.5kg
- Gross Weight: 10.5kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4380A |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 70V, 100V and 4-16Ω outputs
- 240V AC or 24V DC operation
- 24V DC @ 1 Amp output for external devices
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
This range of booster amplifiers are ideal for installations requiring high power zone amplifiers. Simply choose a power rating according to the wattage required for each zone. |
 |
C8890D |
|
- 700 Channels in 520-550MHz UHF Band
- LCD screen shows channel, frequency, RF/AF signal strength
- 1RU half rack metal desk mount case
- True diversity
- Tone squelch circuit
- Range over 100m in ideal conditions
- 6.35mm line output
- 3 pin balanced XLR mic output
- Up to 12 systems can operate side-by-side on different channels.
|
|
The Redback 700 channel UHF 520-550MHz radio microphone system is a professional system incorporating true diversity reception. This ensures a consistent and clear microphone signal with minimal dropout and noise interference. |
 |
A4387A |
|
- 3 Balanced microphone inputs / 3 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
This 250 Watt 4 channel mixer amplifier is specifically designed for applications requiring up to three microphone inputs, without compromising output power and overall performance. The amplifier feature three inputs which can be configured for either microphone or line level operation. |
 |
A4198 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Headphone output: 105mW RMS per channel
- Headphone distortion: 0.05%
- Min load: 4Ω
- Current draw: 9A max.
- Power: 12V dc
- Dimensions: 205W x 108D x 26Hmm
- Weight: 0.5kg
|
|
Excellent for multi-room audio distribution, this 12V powered four zone amplifier produces 30W RMS per zone (15W RMS per channel) - all from a case just 200mm across! One input source may be connected on the front panel via stereo RCA sockets. |
 |
H5351 |
|
|
|
Heavy duty rack shelf to suit all standard 19 inch racking systems. All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, amplifiers, digital video recorders, monitors, etc. Maximum load 20kg. |
 |
A1709 |
|
- Powered by 24V DC
- 50 event times
- 4 outputs
- Manual override
- LCD readout
- Switching time between 1 second and 24 hours
- Stylish 1RU half rack case
- Includes Power Supply
|
|
A versatile timer which has four switched 24V outputs and four closing contacts which activate simultaneously. It permits a total of 50 event switching times. Each can be set to turn on any single day of the week or on multiple days for up to 24 hours. |
 |
A4037 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 40W RMS respectively. |
 |
H5170 |
|
- Dimensions in mm.
|
|
Pre-punched with either 12(1U) or 24(2U). Tough black powdercoated finish. H 5170 & H 5172 suit the following connectors:
P 0804 XLR 3 Pin Female
P 0824 XLR 5 Pin Female
P 0904 Amphenol XLR 3 Pin Female
P 0924 Amphenol XLR 5 Pin Female
Note: Thi |
 |
A4376 |
|
|
|
1 Pair of bolt on rack ears to allow installation of amplifiers into a 19" rack system. Designed to fit the following Redback models:
A 4375, A 4385, A 4375A, A 4385A, A 4377, A 4387, A 4210, A 4212. |
 |
A3164 |
|
- Dante Interface for Audio Input.
- RCA output Jacks on front panel.
- Converts Dante Audio Signal to Unbalanced Line Level.
- Selectable Dante Sample Rates: 44.1 kHz ~ 96 kHz.
- High Resolution Digital to Analog Conversion
- Power over Ethernet (PoE).
- Excellent Audio quality
|
|
This device is designed to receive two channels audio signal from the Dante network, and converts to analogue RCA outputs. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to receive the low latency of signal from other devices which already connected on the same Dante network. |
 |
C0370 |
|
- Impedance: 600Ω ± 30% balanced, dynamic
- Sensitivity: -73dB ±3dB
- Frequency Response: 100Hz-12kHz
- Length: 450mm
- Connector: 3 pin XLR Type Jack
- Directivity: Unidirectional
|
|
This microphone features speech tailored frequency response with excellent noise isolation and feedback rejection. Complete with flexible gooseneck and built in 3 pin male XLR connector, this is ideal for lecterns, custom paging consoles, church pulpits a |
 |
A4911 |
|
- 2 inputs to 1 output
- Suitable for mic or line signals
- Input 1 vox mutes input 2
- Separate controls for volume and vox sensitivity
- Vox operated 24V dc output for control of external devices
- Compact design
- 24V dc operation via 2.1mm dc jack (power supply sold separately)
- Dimensions: 25H x 105W x 81D mm
|
|
This compact 2 input mixer which accepts either a line level signal or balanced microphone signal for each input. The output signal is suitable for feeding an amplifier with either a line level input or balanced microphone input. Input one will vox mute i |
 |
A4500C |
|
- MP3 bell, prebell & music timing outputs.
- Emergency tones conform to AS 1670.4.
- Random play for prebell and music.
- Easy PC based timing event setup.
- Remote triggering of alert, evac and bell.
- Provision for connection to A4660 touchscreen paging console.
- Switched 24VDC out for bell, alert/evac.
- Pluggable screw terminal connections.
- Auxiliary level output.
- Battery backup of current time.
- 24V DC operation.
- Standard 1U 19” rack mount case.
- Suitable for any amp with an aux input.
- 10 Year Warranty
- Australian Designed and Manufactured
- Includes Power Supply
|
|
A weekly timer and evacuation controller all housed in a convenient 1RU rack mount chassis. A total of 200 “event” switching times are available through the timing functions. Each event can be set to turn on from 1 sec up to 24 hours. |
 |
A2620 |
|
- 4 x unbalanced 6.35mm inputs
- 1 x unbalanced 6.35mm outputs
- 24dB total gain
- Frequency response: 10-100KHz
- THD: less than 0.05%
- Signal to noise ratio: >80dB
- Dimensions: 152 x 84 x 52mm
- Input impedance: 30K Ohm
- Output impedance: 600/5K Ohm unbalanced, 1.2K/10K Ohm unbalanced
- Max unbalanced output level: +16dB
- 9V battery power (20 hour battery life)
- 9-12V DC plugpack input
|
|
This compact mono mixer allows 4 channels of audio to be mixed via 6.35mm unbalanced connections. It features 4 x 6.35mm unbalanced inputs, 1 x 6.35mm balanced master output, master volume control.
Can be operated by 9V battery or 12V plugpack. Sold se |
 |
C0335 |
|
|
|
Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord 2m (including switch pair). Suitable for CB''''s, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz |
 |
A4411 |
|
- 2 microphone inputs
- Phantom power on MIc inputs (15V DC)
- 2 line inputs
- Separate tone controls for line and microphones
- Stereo outputs
- 1RU 19” rack mount case
- Master volume on rear panel
- Adjustable line muting
- Front panel mount microphone and line input
- Subwoofer output
- LED VU meter
- VOX active indicator
- Signal Present indicator
- 24V DC input
- 24V DC battery back up terminals
- 10 Year Warranty
- Australian designed & assembled
|
|
This 4 Channel Stereo Mixer has been designed to meet the growing demands of PA systems utilising high power stereo amplifiers, it features 2 balanced microphone and 2 auxiliary inputs. Perfect for aerobics use, bars, bistros, sporting clubs. |
 |
HD5506
|
|
- IP20 rated protection.
- RAL9004/5 black colour.
- SPCC cold rolled steel construction with 1.5mm steel mounting posts and back panel, 1.2mm frame.
- Designed to comply with 19" international standard.
- Complies with ANSI/EIA RS-310-D, IEC297- 2,DIN41491 - PART1, DIN41494 - PART7, GB/3047.2-92 standard.
- Adjustable mounting post to suit different depth equipment.
- Tempered glass front door with 180 deg. rotatable lock.
- Removable side and rear panels for easy installation and adjustment of equipment.
- Ventilation in all doors.
- Cable entry on the top cover.
- Adjustable cable entries in the bottom with panels.
- Adjustable feet included.
- Includes screws and cage nuts.
- Cooling fan holes in top cover.
- Supplied flat pack - assembles quickly.
|
|
Constructed from 1.5mm black powdercoated steel, these 19" racks are ideal for communications, public address and IT server rooms. The design offers both the option of wall mounting or floor standing as desired. |
 |
A4159 |
|
- Output Power (Stereo 8Ω): 350W + 350W
- TA 1KHz THD≤1% (4Ω): 500W + 500W
- Bridge 8Ω: 1000W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <440W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 9.5kg
- Gross Weight: 11.5kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
C0446A |
|
 Designed & manufactured in Australia.
- Since 1976 Redback public address products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
3pin XLR microphone connector mounted horizontally on a dual face wall plate. "One-Shot" version with screw terminal connections for quick and easy connection on site. |
 |
A3042 |
|
- Connections: Input and output RCA
- Frequency response: 20Hz to 20kHz
- Gain control: 0 to 15dB
- Maximum input level: 9V p-p@0dB, 1.5Vp-p @15dB
- Input impedance: 47kΩ
- Output impedance: 100Ω
- Total Harmonic Distortion: <0.002%
- Signal to Noise Ratio: >85dB
- Power Source: 12V DC
- Dimensions: 109L x 73W x 43H mm
- Weight: 160g
|
|
This compact stereo pre-amplifier is a great way to boost the output from your mobile devices and anything else with a low output. |
 |
A3196 |
|
- Output impedance: 16Ω minimum
- THD: 0.05% @ 1kHz
- Power: 5V dc (via micro USB or plugpack)
- Dimensions: 97 x 64 x 30mm
|
|
This single channel headphone amplifier is ideal for systems requiring additional audio level due to impedance differences between the audio source and headphone. |
 |
A4332 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 40W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A2339 |
|
|
|
This controller has been designed to install to a double electrical flush box or wall mounting block. Massive 100 watt capacity available. 11 settings plus off. Fitted with a 24V override relay.
2 Year Warranty |
 |
A3051 |
|
|
|
A low noise pre-amplifier with RIAA equalisation circuitry for connecting your turntable up to a standard auxillary input on a mixer or amplifier. Suitable for use with 'Moving Magnet' pickups. powered by a 9V battery. Compact design fits easily behind an |
 |
C7202C |
|
- Dual channel 96 frequency wireless UHF receiver (Can operate with up to 4 wireless microphones with the addition of a second C 7317C dual channel receiver).
- Bluetooth wireless audio streaming in-built
- Truly portable design
- Battery level indicator
- Compact design sets up in just seconds
- Rugged heavy duty ABS cabinet
- ‘Luggage’ type trolley wheels
- In-built extendible handle
- High performance 120W amplifier (80W RMS)
- Built in backup battery
- Provision for additional radio microphone receiver (520-544MHz)
- Suitable for desk or speaker stand mounting
- Optional wireless link for cable free transmission to additional systems
- RCA line input/output
- Two wired microphone inputs
- 240V AC mains or battery operation
|
|
With an output of 120W, this new release from Okayo is an excellent choice for addressing large crowds up to 500 or more. The cabinet is moulded from industrial grade ABS plastic ensuring long life and the ability to absorb day-to-day wear and tear. |
 |
H5340A |
|
|
|
Ideal for mounting computer keyboard or equipment which needs to be readily accessible. Tough black powdercoated finish. Supplied in flat pack format which assembles in minutes. Base size 415W x 350Dmm. Extends 340mm. |
 |
A2365 |
|
- Standard 2 unit (88mm) 19" rack mount dimensions
- Five Zone outputs
- Accepts 1 to 5 inputs
- Each zone has 10 positions plus off
- 500W total load capacity (100W per zone)
- Easy to terminate screw terminals
- Unit is supplied with an engraving strip which can be fitted with double sided tape (supplied)
- Includes 24V DC override relay for bypassing volume controller settings.
|
|
These controllers can be configured as either five single inputs to five outputs or one input to five outputs. Each zone has a capacity of 100W and total load capacity of 500W. |
 |
A3044 |
|
- Input: 6.35mm Dynamic microphone
- Input impedance: 600Ω
- Pre-amplifier Gain: 50dB
- Signal to Noise Ratio: 80dB
- Power Source: 12V DC
- Discreet Mode: MIC 1 (Left) to RCA Left only; MIC 2 (Right) to RCA Right only.
- Mixed mode: Mixed Mono (not stereo) output (MIC 1 + MIC 2 to RCA (L+R)).
- RCA output: Line level 1Vpp~3Vpp (according to MIC Input Level).
- Microphone 6.35mm TRS mono inputs: Not suitable for connection of line level output devices like iPods etc. Mics only.
|
|
Dual microphone preamplifiers that can be mixed in stereo or operated separately. Dual inputs, Dual outputs. Includes 12V power supply. |
 |
A4322 |
|
- 5 inputs
- 4 output zones
- 70V or 100V output
- 4Ω or 8Ω output
- 24V DC operation
- Over temperature, over current and short circuit protection
- LED VU meter
- 2 year warranty
- Telephone paging input
- Chime and siren
|
|
An economical solution for smaller installations including offices, workshops, smaller shopping arcades, schools etc. |
 |
A4906 |
|
- Mic, line or 100V input level.
- Line level output.
- Phantom power to Mic Input (12V DC).
- Controls for master volume and VOX sensitivity.
- VOX operated relay outputs.
- 24VDC switched output. (120mA Max).
- 24VDC operation via 2.1mm DC power jack.
- Dimensions 133W x 30H x 80D mm.
|
|
The A 4906 is a versatile unit which accepts either a line level signal, balanced microphone signal or 100V input signal.
The output signal is a line level signal suitable for feeding into an amplifier. |
 |
A4432 |
|
- Four Mic/ Line Input channels (Inputs 1-4)
- Four switched RCA AUX Input channels
- Remote AUX source selection, volume and Local input source volume control via optional A 4433 and A 4931 wall plates
- PTT Input and 24V PTT output (limited to 120mA) on inputs 1-4
- Micro SD card based Alert/Evac/Chime/Voice-over module (In built)
- Individual level, bass and treble control on all inputs
- 3.5mm music input overrides AUX 4
- Three levels of priority
- Adjustable Vox sensitivity on inputs 1-4
- Adjustable input sensitivity 1V/100mV on inputs 1-4 and Aux inputs 1-4
- Phantom Power on inputs 1-4
- Tape out (Dual RCA)
- Balanced Output (XLR male)
- Five sets of closing contacts for message triggering (Alert/Evac/Ch1/Ch2/Cancel)
- 24V DC switched output (Limited to 120mA)
- MP3 active indicator
- Signal Present indicator
- LED VU Meter
- 24V DC operation (Plugpack Supplied)
- 24V DC battery back up terminals
|
|
Designed in conjunction with pro-sound contractors, the A 4432 is a stand alone mixer which provides a flexible way to bring multiple audio sources together. It combines many of the best features from our popular mixer and signal processing range into one compact unit. |
 |
C9620A |
|
|
|
This unit will convert speaker level output from a head unit to a low level input suitable for feeding directly into an amplifier input. |
 |
A2081 |
|
|
|
Allows the A 4574, A 4500A and A 4565 units to be activated remotely. Featuring alert, evacuation, chime and cancel buttons with protective “flip up” covers to prevent accidental operation.
|
 |
A1745 |
|
- To mount any of the Redback half rack products into a 19" wide racking system, the H 4990 bracket is required. If a single product is mounted into the H 4990, then a metal (H 4992) or plastic (H 4993) infill panel can be fitted for a neater finish.
|
|
Connects to any RCA input to provide intervalled messages and background music. The included 8GB SD card can be loaded with your choice of background music and custom messages or promotions. Message intervals can be adjusted between 30 seconds and 7.5 minutes. |
 |
C0379 |
|
- Polar Pattern: Cardioid unidirectional
- Impedance: 600 Ohm
- Frequency Response: 80Hz-12kHz
- Sensitivity: -70dB ±3dB
- Housing: Powder coated zinc diecast
- Cable: 2m Twin shield plus muting pair
- Weight: 960g
|
|
This desk microphone has a tapered low frequency response for articulate speech reproduction and enhanced clarity. Fitted with a 2 metre lead and terminated with 5 pin XLR connector. Includes a PTT mute switching pair. |
 |
H5171 |
|
- Dimensions in mm.
|
|
Pre-punched with either 12(1U) or 24(2U). Tough black powdercoated finish. H 5171 & H 5173 suit the following connectors:
P 0881 Plastic 3 Pin Male XLR
P 0883 Plastic 3 Pin Female XLR
P 0833 Neutrik HDMI Chassis D Series Silver.
P 0850 Neutrik 3 Pin |
 |
A4904 |
|
- 1 input to 2 outputs
- Adjustable input and output signals
- Individual volume controls for each output
- Internally selectable phantom power available on XLR input
- 24V dc operation
- Compact design, 25H x 105W x 81D mm
|
|
This compact signal splitter is provided with two input sockets. The 3 pin XLR can be configured for either 3mV or 1V sensitivity, whilst the RCA auxiliary input can be set for either 100mV or 1V sensitivity. |
 |
H5179 |
|
|
|
Provides internal protection for racks from dust and debris whilst still allowing terminated cables to enter for quick connection when you need it. Brush opening size 28H x 388Wmm. |
 |
A2260 |
|
- Designed & manufactured in Australia.
- Since 1976 Redback public address products have been manufactured in Perth, Western Australia by Altronics. With over 45 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
New models supplied with two facia covers to suit your decor.
Designed to control 100V line speaker systems these attenuators are fitted to industry standard wall plates and install into an electrical wall box. They feature 11 position switches |
 |
A4660 NEW
|
|
- Standard Features:
- Touch control paging with pre and post announcement chime options.
- Adjustable microphone automatic gain control (AGC).
- High quality electret microphone with high ambient noise control and feedback rejection.
- Adjustable backlight brightness and dimmed brightness levels with selectable timeout period.
- All glass front bezel for a stylish finish for any room.
- Connects via economical Cat5e UTP cabling.
|
|
This paging console is designed to provide general paging to zones when connected to the Redback A 4450, A 4460 or A 4650 systems. It provides a visual indication of the status of all audio sources and zones within the system at a glance, sharing a common screen with the master wallplates available for use with these systems. |
 |
A2630 |
|
- Input connection: 3.5mm TRS, 6.35mm TRS, stereo RCA
- Input impedance: 22KΩ
- Max input level: +22dB
- Output connection: 6.35mm TRS
- Output impedance: Min 16Ω
- Max gain: 19dB/channel
- Power: 12-18V dc
- Dimensions: 113 x 73 x 40mm
|
|
A compact headphone amplifier featuring four individual channels with volume controls. Ideally suited to monitoring in band and stage environments, it can also be used in educational situations such as language labs. Amplification and individual volume c |
 |
C7217C |
|
- C 7195C Wireless Belt Pack 96 Channel 520-544MHz
- C 7192C Wireless Handheld Microphone 96 Channel 520-544MHz
- C 7193C Wireless Handheld Condenser Microphone 96 Channel 520-544MHz
|
|
With an output of 150W this is an excellent choice for addressing large crowds up to 500 or more. The cabinet is moulded from industrial grade ABS plastic ensuring long life and the ability to absorb day-to-day wear and tear. |
 |
A4427 |
|
- Eight input channels
- Micro SD card message player for audio announcements
- Individual level, bass and treble control on all inputs
- Six levels of VOX priority
- Adjustable VOX sensitivity
- 3.5mm music input
- Adjustable input sensitivity on line inputs
- 24V DC battery back up terminals
- In built Alert/Evac/Chime functionality
- 24V DC output
- MP3 active indicator
- LED VU meter
- 10 Year Warranty
- Australian Designed and Manufactured
|
|
This unique Redback PA mixer features four input channels which are user selectable for either balanced mic, line or auxiliary use. In addition it incorporates a four channel SD card based message player making it an excellent choice for retail, supermarkets, hardware stores and more. |
 |
A2246 |
|
- Designed & manufactured in Australia.
- Since 1976 Redback public address products have been manufactured in Perth, Western Australia by Altronics. With over 45 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
Designed to control 100V line speaker systems these attenuators are fitted to industry standard wall plates and install into an electrical wall box. They feature 11 position switches |
 |
P8166 NEW
|
|
- 240V AC 10A outputs.
- 7 x Australian Sockets (AS/NZS 3112:2017 conforming).
- Electrical authority outlet device approved (AS/NZS 3105:2014 conforming).
- High surge protection.
- Overload protection.
- Power cord located at the rear for less interference.
- 19” rack ear mounting.
|
|
The neat solution to supplying mains power to your mounted equipment. |
 |
A4324 |
|
- 5 inputs
- 4 output zones
- 70V or 100V output
- 4Ω or 8Ω output
- 24V DC operation
- Over temperature, over current and short circuit protection
- LED VU meter
- 2 year warranty
- Telephone paging input
- Chime and siren
|
|
An economical solution for smaller installations including offices, workshops, smaller shopping arcades, schools etc. |
 |
A4310 |
|
- 85% efficient class-D power performance.
- Low power consumption & heat generation.
- Compact 1RU case housing four individual amplifiers.
- Individual dedicated protection circuitry.
- Individual cooling systems for each channel.
- LED indicators for signal, peak, protection and power.
- Constant 100V floating output per channel (ie no reference to earth).
- Compatible with Altronics line monitoring equipment.
- 24V DC battery backup power.
- 240V AC operation.
- Remote control on/off switching function.
- In-built bandpass filter for 80Hz and 16KHz signals.
- Built-in short circuit, overload, high temperature protection.
- 2 year warranty
|
|
Excellent for multizone public address paging and background music systems! Engineered to meet the growing demands of venues such as RSL clubs, taverns, hotels, conference & function centres enabling individual program sources to play to different rooms |
 |
A4390A |
|
- Multi-stage thermally cued fan cooling
- Input signal presence indicator
- Output peak limited
- 2U 19" rack mount (ears included)
- 3 pin XLR input, 3 pin XLR loop out
- Level control rear mounted
- 100V, 70V and 4 - 16Ω outputs
- Thermal and overload protection
- 240V AC, or 24V DC operation
- 300mA 24V battery trickle charge
|
|
This booster is ideal for installations requiring a high power zone amplifier. Ideal for use in shopping centres, pedestrian precincts, public transport facilities and convention centres. |
 |
H5509A |
|
|
|
These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. |
 |
A4330 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 20W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
C8882B |
|
- Operating frequencies 520 / 524.30MHz
- 19” 1RU rack mount case
- Steel enclosure construction
- Removable aerials
- Individual 3 pin XLR outputs
- Mixed 6.35mm jack output (1m cable included)
- Front panel level controls
- Tone squelch circuit for noise reduction
- RF, AF & peak signal LEDs
- Range up to 50m in ideal conditions
|
|
For systems requiring the freedom of two independent wireless microphones at an economical price. The sturdy 19" rack mount cabinet is fitted with two fixed frequency wireless receivers. The miniaturised SMD construction and unique shielding technique, pl |
 |
C8867C |
|
- 16 Channels in 520 - 550MHz UHF Band
- RF and AF signal presence LEDs
- Tone squelch circuit for noise reduction
- Range up to 70m in ideal conditions
- 6.35mm unbalanced line/mic output
- 3 pin balanced XLR mic output
- Microphone transmitters require 2 x AA batteries (not included).
|
|
The perfect entry level 16 channel UHF wireless microphone system for clubs, restaurants, function centres, wedding ceremonies etc. It produces a clear, crisp vocal reproduction, whilst allowing freedom of movement. Supplied as a complete "ready to go" system with a handheld microphone transmitter. |
|
H5412A |
|
|
|
These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. |
 |
C0383 ROHS
|
|
- Polar Pattern: Unidirectional
- Housing Material: Zinc Diecast
- Impedance: 600 Ohm
- Sensitivity: -72dB ±3dB
- Frequency Response: 50Hz - 15kHz
|
|
This balanced microphone has a specially designed grill that can withstand a drop impact without losing its shape. The tough zinc diecast housing has an inbuilt 3 pin XLR male connector and on/off switch. It is supplied complete with 5m twin shielded bala |
 |
A4450 |
|
- 4 mic/line inputs to 4 zones
- Operates as a matrix mixer or source switcher
- Touchscreen & iOS/Android app control
- RS-485 control via rear panel serial adapter connection
- Adjustable aux level 100mV/1V
- Adjustable balanced mic/line level 3mV/0.7V
- LCD for easy selection of sources to zones
- System cabling via Cat5e UTP.
- Zone and input custom labelling
- Adjustable volume for each input to output selection
- Master & zone source selection wallplates
- 24V DC operation
|
|
This Redback 4x4 audio source matrix system is feature packed yet simple to set up and use it features 4 inputs, selectable to up to 4 zones making it ideally suited to gyms, cafes, restaurants, small clubs and function centres. |
 |
A4573 |
|
- Designed & manufactured in Australia.
- Since 1976 Redback public address products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
Optional Plugin Board to suit the Phase 4 range of Redback Amplifiers. It generates pre chime, bell, alert and evacuation tones. The alert tone can function continuously, or switch to evac tone after a preset time delay (adjustable 30 seconds to 4.5 minu |
 |
A2078B |
|
-
- 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
 Backed by an industry leading 10 Year Manufacturer Warranty.
- Our Redback products have a long tried and tested history of bulletproof reliability. Altronics offers a 10 Year Warranty on all Australian Made Redback products. Our local in-house service department has all the know how to answer technical queries and provide timely service. Read more about our industry leading warranty.
|
|
Allows the A 4565 or A 4574 alert/evac unit to be activated remotely. Featuring alert, evacuation and cancel buttons with protective “flip up” covers to prevent accidental operation. Connects to main unit via multi core cable (7 core). |
 |
A1715 |
|
- Four MP3 audio messages available
- Micro SD Card storage of MP3 files (supplied)
- Stereo Dual RCA output
- Remote triggering of MP3 playback
- Manual playback of MP3 files
- 24V DC operation
- Supplied with 24V DC plugpack
|
|
The A 1715 is an MP3 based message player, housed in a convenient DIN rail housing. It has four independent contacts for remote triggering
of the four available MP3 audio files. |
 |
A3195A |
|
- Built-in high performance RTOS operating system and
- audio decoder chip; supports DTS/AC-3
- Super fast start time about 3 seconds
- Auto Switch between optical and coaxial channel input
- Auto decode AC-3/DTS (LPCM/PCM/RAW) input signal without any action
- High compatibility
- Small size
- Metal case, Anti-interference
- Headphone port output
- Supports volume adjustment
|
|
This Audio decoder can auto convert optical/coaxial channel (Support LPCM/PCM/RAW) input to 2.0 channel analog audio output, and supports decoding Dolby AC-3/DTS (included 5.1 RAW digital audio streaming). |
 |
A2055A |
|
- Microphone gain: 60 dB
- Mic input sensitivity: 0.7 mV rms
- S/N ratio: 10 mV input -74dB
- Frequency resp.: 150Hz to 20kHz , -3dB
- Line. gain: 14dB
- Line. input sensitivity: 200mV
- Line. S/N ratio: 500mV input -77dB
- Line. freq. resp.: 30Hz to 20kHz, -3dB
|
|
Features two line inputs and one mic input, each with its own level control. The mic input can be configured for either balanced or unbalanced operation. All inputs are mixed to a single line level output. It can be powered from either a single rail po |
 |
C0411 |
|
|
|
Microphone gooseneck incorporating 5/8" thread male to female. Matching bench mount bases C 0420/21. 300mm Black. |
 |
A2312A |
|
- Pluggable terminal connections
- Adjustable impedance selection
- Suis for up to 8 pairs of stereo speakers
- Compatible with all 8 ohm stereo amplifiers
- No power loss
- No heat generation
- No loss of audio quality
|
|
This volume control is rated at 100 watts (50W per channel). It features selectable impedance matching, allowing up to 8 pairs of speakers to be controlled. Includes 11 settings plus Off. Connections are made via a pluggable terminal block. 60mm mounting |
 |
A4116 |
|
- 15W RMS per channel
- 1 music input (3.5mm)
- 1 auxiliary input
- 4-16Ω output
- 240V ac operation
- Includes Power Supply
|
|
Packed with features, this super compact stereo amp is ideally suited to classrooms, boardrooms, boutiques, reception areas or anywhere a small functional stereo system is required. Designed in close consultation with several leading AV installation compa |
 |
A4212 |
|
- Designed to meet AS60118.4-2007
- Coverage up to 650m2
- XLR line & mic inputs
- Aux input via stereo RCA
- EWIS signal connection (RCA)
- Short circuit proof
- Compressor for added speech intelligibility
- Adjustable VOX sensitivity
- Compatible with single loop designs
|
|
Hearing induction loop amplifiers are installed to greatly enhance the listening experience of people using hearing aids. They are commonly installed in public areas which are generally noisy, making it difficult for hearing impaired users to hear clearly. |
 |
A3052 |
|
- For all turntables with moving magnet (MM) cartridges or audio devices with line level (e.g. tape decks)
- External housing, reliably shielded against interference
- Top quality circuit technology and components
- Built-in low-noise phono preamp circuit conforms to the RIAA standard
- Power supply included
|
|
This phono preamp can be used to raise your turntable's output to make it compatible with modern amplifiers. At the same time, it adds standardised equalisation. Users may need this phono preamp because their turntable either doesn't have one, in which case they won't be able to play records without one. |
 |
C0327 |
|
- All metal casing and grille.
- PTT pair for muting auxiliary inputs.
- Heavy duty bare end cord.
- 450mm gooseneck with screw fit base.
- Ideal for supermarkets, fast food restaurants etc.
|
|
This incredibly sturdy all metal microphone is built to survive the rigours of supermarkets & fast food restaurants. |
 |
A2347 |
|
- Power rating: 200W (40W per zone)
- Relay override operation voltage: 24V DC
- Dimensions: 484W x 50D x 88H mm
- Weight: 2.3kg
|
|
May be configured to either five single inputs to five outputs or one input to five outputs. Each zone has a 40W and 100W load capacity respectively, with a total panel capacity of 200W and 500W. Has 11 settings plus 'off'. The input and outputs are conn |
 |
A4173A |
|
- Rugged heavy duty construction
- 19” rack mount
- Bridgeable, parallel or two channel stereo operation
- Earth lift switch
- 3 pin XLR inputs.
- Short circuit protection with indicator
- Overload protection with indicator
- Clipping prevention circuitry with indicator
- Variable speed fan forced cooling
- Muting circuit for switch on/off
|
|
This new series dubbed the "Apple" range have been completely redesigned by Biema to offer vastly improved cooling, efficiency and circuit protection. This range is designed to function as a stereo or high power single channel amplifier for use in foreground sound reinforcement ie: pubs, clubs, cinemas and multi-function venues. |
 |
C0375 |
|
- Impedance: 100Ω
- Sensitivity: -58dB ± 3dB
- Frequency response: 70Hz - 15kHz
- Cable Connection: Mini XLR
- Length: 330mm
- Polar pattern: Cardioid (unidirectional)
- Voltage: 11 - 52 Volts DC
|
|
An elegant, stylish, slimline unobtrusive desk-mount paging microphone equipped with a 3 pin balanced XLR lead. Features switchable flat or rolloff response to eliminate low frequency pickup. May also be switched to operate as push to talk or push to lock |
 |
C7192C |
|
- Exceptional performance
- Textured body
- Requires 2 x AA batteries, either alkaline (14 hour use) or rechargeable (11 hours use).
|
|
Handheld transmitter. 520-544MHz. Please ensure your system is compatible with this frequency before making your purchase. |
